new file mode 100644
@@ -0,0 +1,51 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/mediatek/mediatek,cec.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Mediatek HDMI CEC Controller Device Tree Bindings
+
+maintainers:
+ - CK Hu <ck.hu@mediatek.com>
+ - Jitao shi <jitao.shi@mediatek.com>
+
+description: |
+ The HDMI CEC controller handles hotplug detection and CEC communication.
+
+properties:
+ compatible:
+ enum:
+ - mediatek,mt7623-hdmi
+ - mediatek,mt8173-hdmi
+
+ reg:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ clocks:
+ maxItems: 1
+
+required:
+ - compatible
+ - reg
+ - interrupts
+ - clocks
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/clock/mt8173-clk.h>
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ #include <dt-bindings/interrupt-controller/irq.h>
+ cec: cec@10013000 {
+ compatible = "mediatek,mt8173-cec";
+ reg = <0x10013000 0xbc>;
+ interrupts = <GIC_SPI 167 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&infracfg CLK_INFRA_CEC>;
+ };
+
+...
new file mode 100644
@@ -0,0 +1,57 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/mediatek/mediatek,hdmi-ddc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Mediatek HDMI DDC Device Tree Bindings
+
+maintainers:
+ - CK Hu <ck.hu@mediatek.com>
+ - Jitao shi <jitao.shi@mediatek.com>
+
+description: |
+ The HDMI DDC i2c controller is used to interface with the HDMI DDC pins.
+
+properties:
+ compatible:
+ enum:
+ - mediatek,mt7623-hdmi
+ - mediatek,mt8173-hdmi
+
+ reg:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ clocks:
+ maxItems: 1
+
+ clock-names:
+ items:
+ - const: ddc-i2c
+
+required:
+ - compatible
+ - reg
+ - interrupts
+ - clocks
+ - clock-names
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/clock/mt8173-clk.h>
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ #include <dt-bindings/interrupt-controller/irq.h>
+ hdmi_ddc0: i2c@11012000 {
+ compatible = "mediatek,mt8173-hdmi-ddc";
+ reg = <0x11012000 0x1c>;
+ interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&pericfg CLK_PERI_I2C5>;
+ clock-names = "ddc-i2c";
+ };
+
+...
deleted file mode 100644
@@ -1,136 +0,0 @@
-Mediatek HDMI Encoder
-=====================
-
-The Mediatek HDMI encoder can generate HDMI 1.4a or MHL 2.0 signals from
-its parallel input.
-
-Required properties:
-- compatible: Should be "mediatek,<chip>-hdmi".
-- the supported chips are mt2701, mt7623 and mt8173
-- reg: Physical base address and length of the controller's registers
-- interrupts: The interrupt signal from the function block.
-- clocks: device clocks
- See Documentation/devicetree/bindings/clock/clock-bindings.txt for details.
-- clock-names: must contain "pixel", "pll", "bclk", and "spdif".
-- phys: phandle link to the HDMI PHY node.
- See Documentation/devicetree/bindings/phy/phy-bindings.txt for details.
-- phy-names: must contain "hdmi"
-- mediatek,syscon-hdmi: phandle link and register offset to the system
- configuration registers. For mt8173 this must be offset 0x900 into the
- MMSYS_CONFIG region: <&mmsys 0x900>.
-- ports: A node containing input and output port nodes with endpoint
- definitions as documented in Documentation/devicetree/bindings/graph.txt.
-- port@0: The input port in the ports node should be connected to a DPI output
- port.
-- port@1: The output port in the ports node should be connected to the input
- port of a connector node that contains a ddc-i2c-bus property, or to the
- input port of an attached bridge chip, such as a SlimPort transmitter.
-
-HDMI CEC
-========
-
-The HDMI CEC controller handles hotplug detection and CEC communication.
-
-Required properties:
-- compatible: Should be "mediatek,<chip>-cec"
-- the supported chips are mt7623 and mt8173
-- reg: Physical base address and length of the controller's registers
-- interrupts: The interrupt signal from the function block.
-- clocks: device clock
-
-HDMI DDC
-========
-
-The HDMI DDC i2c controller is used to interface with the HDMI DDC pins.
-The Mediatek's I2C controller is used to interface with I2C devices.
-
-Required properties:
-- compatible: Should be "mediatek,<chip>-hdmi-ddc"
-- the supported chips are mt7623 and mt8173
-- reg: Physical base address and length of the controller's registers
-- clocks: device clock
-- clock-names: Should be "ddc-i2c".
-
-HDMI PHY
-========
-See phy/mediatek,hdmi-phy.yaml
-
-Example:
-
-cec: cec@10013000 {
- compatible = "mediatek,mt8173-cec";
- reg = <0 0x10013000 0 0xbc>;
- interrupts = <GIC_SPI 167 IRQ_TYPE_LEVEL_LOW>;
- clocks = <&infracfg CLK_INFRA_CEC>;
-};
-
-hdmi_phy: hdmi-phy@10209100 {
- compatible = "mediatek,mt8173-hdmi-phy";
- reg = <0 0x10209100 0 0x24>;
- clocks = <&apmixedsys CLK_APMIXED_HDMI_REF>;
- clock-names = "pll_ref";
- clock-output-names = "hdmitx_dig_cts";
- mediatek,ibias = <0xa>;
- mediatek,ibias_up = <0x1c>;
- #clock-cells = <0>;
- #phy-cells = <0>;
-};
-
-hdmi_ddc0: i2c@11012000 {
- compatible = "mediatek,mt8173-hdmi-ddc";
- reg = <0 0x11012000 0 0x1c>;
- interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_LOW>;
- clocks = <&pericfg CLK_PERI_I2C5>;
- clock-names = "ddc-i2c";
-};
-
-hdmi0: hdmi@14025000 {
- compatible = "mediatek,mt8173-hdmi";
- reg = <0 0x14025000 0 0x400>;
- interrupts = <GIC_SPI 206 IRQ_TYPE_LEVEL_LOW>;
- clocks = <&mmsys CLK_MM_HDMI_PIXEL>,
- <&mmsys CLK_MM_HDMI_PLLCK>,
- <&mmsys CLK_MM_HDMI_AUDIO>,
- <&mmsys CLK_MM_HDMI_SPDIF>;
- clock-names = "pixel", "pll", "bclk", "spdif";
- pinctrl-names = "default";
- pinctrl-0 = <&hdmi_pin>;
- phys = <&hdmi_phy>;
- phy-names = "hdmi";
- mediatek,syscon-hdmi = <&mmsys 0x900>;
- assigned-clocks = <&topckgen CLK_TOP_HDMI_SEL>;
- assigned-clock-parents = <&hdmi_phy>;
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- reg = <0>;
-
- hdmi0_in: endpoint {
- remote-endpoint = <&dpi0_out>;
- };
- };
-
- port@1 {
- reg = <1>;
-
- hdmi0_out: endpoint {
- remote-endpoint = <&hdmi_con_in>;
- };
- };
- };
-};
-
-connector {
- compatible = "hdmi-connector";
- type = "a";
- ddc-i2c-bus = <&hdmiddc0>;
-
- port {
- hdmi_con_in: endpoint {
- remote-endpoint = <&hdmi0_out>;
- };
- };
-};
new file mode 100644
@@ -0,0 +1,131 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/mediatek/mediatek,hdmi.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Mediatek HDMI Encoder Device Tree Bindings
+
+maintainers:
+ - CK Hu <ck.hu@mediatek.com>
+ - Jitao shi <jitao.shi@mediatek.com>
+
+description: |
+ The Mediatek HDMI encoder can generate HDMI 1.4a or MHL 2.0 signals from
+ its parallel input.
+
+properties:
+ compatible:
+ enum:
+ - mediatek,mt2701-hdmi
+ - mediatek,mt7623-hdmi
+ - mediatek,mt8173-hdmi
+
+ reg:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ clocks:
+ items:
+ - description: Pixel Clock
+ - description: HDMI PLL
+ - description: Bit Clock
+ - description: S/PDIF Clock
+
+ clock-names:
+ items:
+ - const: pixel
+ - const: pll
+ - const: bclk
+ - const: spdif
+
+ phys:
+ maxItems: 1
+
+ phy-names:
+ items:
+ - const: hdmi
+
+ mediatek,syscon-hdmi:
+ $ref: '/schemas/types.yaml#/definitions/phandle'
+ minItems: 2
+ description: |
+ phandle link and register offset to the system configuration registers.
+
+ ports:
+ $ref: /schemas/graph.yaml#/properties/ports
+
+ properties:
+ port@0:
+ $ref: /schemas/graph.yaml#/properties/port
+ description: |
+ Input port node. This port should be connected to a DPI output port.
+
+ port@1:
+ $ref: /schemas/graph.yaml#/properties/port
+ description: |
+ Output port node. This port should be connected to the input port of a connector
+ node that contains a ddc-i2c-bus property, or to the input port of an attached
+ bridge chip, such as a SlimPort transmitter.
+
+ required:
+ - port@0
+ - port@1
+
+required:
+ - compatible
+ - reg
+ - interrupts
+ - clocks
+ - clock-names
+ - phys
+ - phy-names
+ - mediatek,syscon-hdmi
+ - ports
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/clock/mt8173-clk.h>
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ #include <dt-bindings/interrupt-controller/irq.h>
+ hdmi0: hdmi@14025000 {
+ reg = <0x14025000 0x400>;
+ interrupts = <GIC_SPI 206 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&mmsys CLK_MM_HDMI_PIXEL>,
+ <&mmsys CLK_MM_HDMI_PLLCK>,
+ <&mmsys CLK_MM_HDMI_AUDIO>,
+ <&mmsys CLK_MM_HDMI_SPDIF>;
+ clock-names = "pixel", "pll", "bclk", "spdif";
+ pinctrl-names = "default";
+ pinctrl-0 = <&hdmi_pin>;
+ phys = <&hdmi_phy>;
+ phy-names = "hdmi";
+ mediatek,syscon-hdmi = <&mmsys 0x900>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ hdmi0_in: endpoint {
+ remote-endpoint = <&dpi0_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ hdmi0_out: endpoint {
+ remote-endpoint = <&hdmi_con_in>;
+ };
+ };
+ };
+ };
+
+...
Update the mediatek,dpi binding to use the graph schema. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> --- .../display/mediatek/mediatek,cec.yaml | 51 +++++++ .../display/mediatek/mediatek,hdmi-ddc.yaml | 57 ++++++++ .../display/mediatek/mediatek,hdmi.txt | 136 ------------------ .../display/mediatek/mediatek,hdmi.yaml | 131 +++++++++++++++++ 4 files changed, 239 insertions(+), 136 deletions(-) create mode 100644 Documentation/devicetree/bindings/display/mediatek/mediatek,cec.yaml create mode 100644 Documentation/devicetree/bindings/display/mediatek/mediatek,hdmi-ddc.yaml delete mode 100644 Documentation/devicetree/bindings/display/mediatek/mediatek,hdmi.txt create mode 100644 Documentation/devicetree/bindings/display/mediatek/mediatek,hdmi.yaml