deleted file mode 100644
@@ -1,107 +0,0 @@
-Device-Tree bindings for Samsung SoC display controller (FIMD)
-
-FIMD (Fully Interactive Mobile Display) is the Display Controller for the
-Samsung series of SoCs which transfers the image data from a video memory
-buffer to an external LCD interface.
-
-Required properties:
-- compatible: value should be one of the following
- "samsung,s3c2443-fimd"; /* for S3C24XX SoCs */
- "samsung,s3c6400-fimd"; /* for S3C64XX SoCs */
- "samsung,s5pv210-fimd"; /* for S5PV210 SoC */
- "samsung,exynos3250-fimd"; /* for Exynos3250/3472 SoCs */
- "samsung,exynos4210-fimd"; /* for Exynos4 SoCs */
- "samsung,exynos5250-fimd"; /* for Exynos5250 SoCs */
- "samsung,exynos5420-fimd"; /* for Exynos5420/5422/5800 SoCs */
-
-- reg: physical base address and length of the FIMD registers set.
-
-- interrupts: should contain a list of all FIMD IP block interrupts in the
- order: FIFO Level, VSYNC, LCD_SYSTEM. The interrupt specifier
- format depends on the interrupt controller used.
-
-- interrupt-names: should contain the interrupt names: "fifo", "vsync",
- "lcd_sys", in the same order as they were listed in the interrupts
- property.
-
-- pinctrl-0: pin control group to be used for this controller.
-
-- pinctrl-names: must contain a "default" entry.
-
-- clocks: must include clock specifiers corresponding to entries in the
- clock-names property.
-
-- clock-names: list of clock names sorted in the same order as the clocks
- property. Must contain "sclk_fimd" and "fimd".
-
-Optional Properties:
-- power-domains: a phandle to FIMD power domain node.
-- samsung,invert-vden: video enable signal is inverted
-- samsung,invert-vclk: video clock signal is inverted
-- display-timings: timing settings for FIMD, as described in document [1].
- Can be used in case timings cannot be provided otherwise
- or to override timings provided by the panel.
-- samsung,sysreg: handle to syscon used to control the system registers
-- i80-if-timings: timing configuration for lcd i80 interface support.
- - cs-setup: clock cycles for the active period of address signal is enabled
- until chip select is enabled.
- If not specified, the default value(0) will be used.
- - wr-setup: clock cycles for the active period of CS signal is enabled until
- write signal is enabled.
- If not specified, the default value(0) will be used.
- - wr-active: clock cycles for the active period of CS is enabled.
- If not specified, the default value(1) will be used.
- - wr-hold: clock cycles for the active period of CS is disabled until write
- signal is disabled.
- If not specified, the default value(0) will be used.
-
- The parameters are defined as:
-
- VCLK(internal) __|??????|_____|??????|_____|??????|_____|??????|_____|??
- : : : : :
- Address Output --:<XXXXXXXXXXX:XXXXXXXXXXXX:XXXXXXXXXXXX:XXXXXXXXXXXX:XX
- | cs-setup+1 | : : :
- |<---------->| : : :
- Chip Select ???????????????|____________:____________:____________|??
- | wr-setup+1 | | wr-hold+1 |
- |<---------->| |<---------->|
- Write Enable ????????????????????????????|____________|???????????????
- | wr-active+1|
- |<---------->|
- Video Data ----------------------------<XXXXXXXXXXXXXXXXXXXXXXXXX>--
-
-The device node can contain 'port' child nodes according to the bindings defined
-in [2]. The following are properties specific to those nodes:
-- reg: (required) port index, can be:
- 0 - for CAMIF0 input,
- 1 - for CAMIF1 input,
- 2 - for CAMIF2 input,
- 3 - for parallel output,
- 4 - for write-back interface
-
-[1]: Documentation/devicetree/bindings/display/panel/display-timing.txt
-[2]: Documentation/devicetree/bindings/media/video-interfaces.txt
-
-Example:
-
-SoC specific DT entry:
-
- fimd@11c00000 {
- compatible = "samsung,exynos4210-fimd";
- interrupt-parent = <&combiner>;
- reg = <0x11c00000 0x20000>;
- interrupt-names = "fifo", "vsync", "lcd_sys";
- interrupts = <11 0>, <11 1>, <11 2>;
- clocks = <&clock 140>, <&clock 283>;
- clock-names = "sclk_fimd", "fimd";
- power-domains = <&pd_lcd0>;
- status = "disabled";
- };
-
-Board specific DT entry:
-
- fimd@11c00000 {
- pinctrl-0 = <&lcd_clk &lcd_data24 &pwm1_out>;
- pinctrl-names = "default";
- status = "okay";
- };
new file mode 100644
@@ -0,0 +1,198 @@
+# SPDX-License-Identifier: GPL-2.0-only
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/samsung/samsung,fimd.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Samsung S3C/S5P/Exynos SoC Fully Interactive Mobile Display (FIMD)
+
+maintainers:
+ - Inki Dae <inki.dae@samsung.com>
+ - Joonyoung Shim <jy0922.shim@samsung.com>
+ - Seung-Woo Kim <sw0312.kim@samsung.com>
+ - Kyungmin Park <kyungmin.park@samsung.com>
+ - Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
+
+properties:
+ compatible:
+ enum:
+ - samsung,s3c2443-fimd
+ - samsung,s3c6400-fimd
+ - samsung,s5pv210-fimd
+ - samsung,exynos3250-fimd
+ - samsung,exynos4210-fimd
+ - samsung,exynos5250-fimd
+ - samsung,exynos5420-fimd
+
+ '#address-cells':
+ const: 1
+
+ clocks:
+ minItems: 2
+ maxItems: 2
+
+ clock-names:
+ items:
+ - const: sclk_fimd
+ - const: fimd
+
+ display-timings:
+ $ref: ../panel/display-timings.yaml#
+
+ i80-if-timings:
+ type: object
+ description: |
+ Timing configuration for lcd i80 interface support.
+ The parameters are defined as::
+ VCLK(internal) __|??????|_____|??????|_____|??????|_____|??????|_____|??
+ : : : : :
+ Address Output --:<XXXXXXXXXXX:XXXXXXXXXXXX:XXXXXXXXXXXX:XXXXXXXXXXXX:XX
+ | cs-setup+1 | : : :
+ |<---------->| : : :
+ Chip Select ???????????????|____________:____________:____________|??
+ | wr-setup+1 | | wr-hold+1 |
+ |<---------->| |<---------->|
+ Write Enable ????????????????????????????|____________|???????????????
+ | wr-active+1|
+ |<---------->|
+ Video Data ----------------------------<XXXXXXXXXXXXXXXXXXXXXXXXX>--
+
+ properties:
+ cs-setup:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ Clock cycles for the active period of address signal is enabled until
+ chip select is enabled.
+ default: 0
+
+ wr-active:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ Clock cycles for the active period of CS is enabled.
+ default: 1
+
+ wr-hold:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ Clock cycles for the active period of CS is disabled until write
+ signal is disabled.
+ default: 0
+
+ wr-setup:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ Clock cycles for the active period of CS signal is enabled until
+ write signal is enabled.
+ default: 0
+
+ iommus:
+ minItems: 1
+ maxItems: 2
+
+ iommu-names:
+ items:
+ - const: m0
+ - const: m1
+
+ interrupts:
+ items:
+ - description: FIFO level
+ - description: VSYNC
+ - description: LCD system
+
+ interrupt-names:
+ items:
+ - const: fifo
+ - const: vsync
+ - const: lcd_sys
+
+ power-domains:
+ maxItems: 1
+
+ reg:
+ maxItems: 1
+
+ samsung,invert-vden:
+ type: boolean
+ description:
+ Video enable signal is inverted.
+
+ samsung,invert-vclk:
+ type: boolean
+ description:
+ Video clock signal is inverted.
+
+ samsung,sysreg:
+ $ref: /schemas/types.yaml#/definitions/phandle
+ description:
+ Phandle to System Register syscon.
+
+ '#size-cells':
+ const: 0
+
+patternProperties:
+ "^port@[0-4]+$":
+ $ref: /schemas/graph.yaml#/properties/port
+ description: |
+ Contains ports with port with index::
+ 0 - for CAMIF0 input,
+ 1 - for CAMIF1 input,
+ 2 - for CAMIF2 input,
+ 3 - for parallel output,
+ 4 - for write-back interface
+
+required:
+ - compatible
+ - clocks
+ - clock-names
+ - interrupts
+ - interrupt-names
+ - reg
+
+allOf:
+ - if:
+ properties:
+ compatible:
+ contains:
+ const: samsung,exynos5420-fimd
+ then:
+ properties:
+ iommus:
+ minItems: 2
+ maxItems: 2
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/clock/exynos4.h>
+
+ fimd@11c00000 {
+ compatible = "samsung,exynos4210-fimd";
+ interrupt-parent = <&combiner>;
+ reg = <0x11c00000 0x20000>;
+ interrupt-names = "fifo", "vsync", "lcd_sys";
+ interrupts = <11 0>, <11 1>, <11 2>;
+ clocks = <&clock CLK_SCLK_FIMD0>, <&clock CLK_FIMD0>;
+ clock-names = "sclk_fimd", "fimd";
+ power-domains = <&pd_lcd0>;
+ iommus = <&sysmmu_fimd0>;
+ samsung,sysreg = <&sys_reg>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ samsung,invert-vden;
+ samsung,invert-vclk;
+
+ pinctrl-0 = <&lcd_clk>, <&lcd_data24>;
+ pinctrl-names = "default";
+
+ port@3 {
+ reg = <3>;
+
+ fimd_dpi_ep: endpoint {
+ remote-endpoint = <&lcd_ep>;
+ };
+ };
+ };
Convert the S3C/S5P/Exynos FIMD bindings to DT schema format. The conversion includes also updates to the bindings, matching the current DTS and Linux driver: adding optional iommus and power-domains. Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> --- .../bindings/display/exynos/samsung-fimd.txt | 107 ---------- .../display/samsung/samsung,fimd.yaml | 198 ++++++++++++++++++ 2 files changed, 198 insertions(+), 107 deletions(-) delete mode 100644 Documentation/devicetree/bindings/display/exynos/samsung-fimd.txt create mode 100644 Documentation/devicetree/bindings/display/samsung/samsung,fimd.yaml