| Message ID | 20221212093315.11390-3-konrad.dybcio@linaro.org (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | [1/3] dt-bindings: display/msm: Add SM8150 MDSS & DPU | expand |
On 2022-12-12 10:33:14, Konrad Dybcio wrote: > Add required nodes for MDSS and hook up provided clocks in DISPCC. > This setup is almost identical to 8[23]50. > > Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org> Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org> On Sony Xperia 5: Tested-by: Marijn Suijten <marijn.suijten@somainline.org> Note that this device uses a command-mode panel which requires (since DPU 5.0.0) the TE functionality to be moved from the PP into the INTF block. I will send patches for this shortly, to enable proper vsyncing and presentation _without_ tearing. Note^2: We are also working to correct Display Stream Compression to work on the Sony Xperia 1 (bigger brother of Xperia 5 with a 4k display) and newer Sony devices on newer (sm8[234]50) SoCs! - Marijn
On Mon, Dec 12, 2022 at 10:33:14AM +0100, Konrad Dybcio wrote: > Add required nodes for MDSS and hook up provided clocks in DISPCC. > This setup is almost identical to 8[23]50. > > Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org> > --- > arch/arm64/boot/dts/qcom/sm8150.dtsi | 271 ++++++++++++++++++++++++++- > 1 file changed, 267 insertions(+), 4 deletions(-) > > diff --git a/arch/arm64/boot/dts/qcom/sm8150.dtsi b/arch/arm64/boot/dts/qcom/sm8150.dtsi > index ff04397777f4..c0c1e781eb43 100644 > --- a/arch/arm64/boot/dts/qcom/sm8150.dtsi > +++ b/arch/arm64/boot/dts/qcom/sm8150.dtsi > @@ -9,6 +9,7 @@ > #include <dt-bindings/power/qcom-rpmpd.h> > #include <dt-bindings/soc/qcom,rpmh-rsc.h> > #include <dt-bindings/clock/qcom,rpmh.h> > +#include <dt-bindings/clock/qcom,dispcc-sm8150.h> > #include <dt-bindings/clock/qcom,gcc-sm8150.h> > #include <dt-bindings/clock/qcom,gpucc-sm8150.h> > #include <dt-bindings/interconnect/qcom,osm-l3.h> > @@ -3579,14 +3580,276 @@ camnoc_virt: interconnect@ac00000 { > qcom,bcm-voters = <&apps_bcm_voter>; > }; > > + mdss: mdss@ae00000 { As you're fixing up the dispcc patch, "display-subsystem@" seems nicer. Regards, Bjorn > + compatible = "qcom,sm8150-mdss"; > + reg = <0 0x0ae00000 0 0x1000>; > + reg-names = "mdss"; > + > + interconnects = <&mmss_noc MASTER_MDP_PORT0 &mc_virt SLAVE_EBI_CH0>, > + <&mmss_noc MASTER_MDP_PORT1 &mc_virt SLAVE_EBI_CH0>; > + interconnect-names = "mdp0-mem", "mdp1-mem"; > + > + power-domains = <&dispcc MDSS_GDSC>; > + > + clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>, > + <&gcc GCC_DISP_HF_AXI_CLK>, > + <&gcc GCC_DISP_SF_AXI_CLK>, > + <&dispcc DISP_CC_MDSS_MDP_CLK>; > + clock-names = "iface", "bus", "nrt_bus", "core"; > + > + interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>; > + interrupt-controller; > + #interrupt-cells = <1>; > + > + iommus = <&apps_smmu 0x800 0x420>; > + > + status = "disabled"; > + > + #address-cells = <2>; > + #size-cells = <2>; > + ranges; > + > + mdss_mdp: display-controller@ae01000 { > + compatible = "qcom,sm8150-dpu"; > + reg = <0 0x0ae01000 0 0x8f000>, > + <0 0x0aeb0000 0 0x2008>; > + reg-names = "mdp", "vbif"; > + > + clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>, > + <&gcc GCC_DISP_HF_AXI_CLK>, > + <&dispcc DISP_CC_MDSS_MDP_CLK>, > + <&dispcc DISP_CC_MDSS_VSYNC_CLK>; > + clock-names = "iface", "bus", "core", "vsync"; > + > + assigned-clocks = <&dispcc DISP_CC_MDSS_VSYNC_CLK>; > + assigned-clock-rates = <19200000>; > + > + operating-points-v2 = <&mdp_opp_table>; > + power-domains = <&rpmhpd SM8150_MMCX>; > + > + interrupt-parent = <&mdss>; > + interrupts = <0>; > + > + ports { > + #address-cells = <1>; > + #size-cells = <0>; > + > + port@0 { > + reg = <0>; > + dpu_intf1_out: endpoint { > + remote-endpoint = <&mdss_dsi0_in>; > + }; > + }; > + > + port@1 { > + reg = <1>; > + dpu_intf2_out: endpoint { > + remote-endpoint = <&mdss_dsi1_in>; > + }; > + }; > + }; > + > + mdp_opp_table: opp-table { > + compatible = "operating-points-v2"; > + > + opp-171428571 { > + opp-hz = /bits/ 64 <171428571>; > + required-opps = <&rpmhpd_opp_low_svs>; > + }; > + > + opp-300000000 { > + opp-hz = /bits/ 64 <300000000>; > + required-opps = <&rpmhpd_opp_svs>; > + }; > + > + opp-345000000 { > + opp-hz = /bits/ 64 <345000000>; > + required-opps = <&rpmhpd_opp_svs_l1>; > + }; > + > + opp-460000000 { > + opp-hz = /bits/ 64 <460000000>; > + required-opps = <&rpmhpd_opp_nom>; > + }; > + }; > + }; > + > + mdss_dsi0: dsi@ae94000 { > + compatible = "qcom,mdss-dsi-ctrl"; > + reg = <0 0x0ae94000 0 0x400>; > + reg-names = "dsi_ctrl"; > + > + interrupt-parent = <&mdss>; > + interrupts = <4>; > + > + clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK>, > + <&dispcc DISP_CC_MDSS_BYTE0_INTF_CLK>, > + <&dispcc DISP_CC_MDSS_PCLK0_CLK>, > + <&dispcc DISP_CC_MDSS_ESC0_CLK>, > + <&dispcc DISP_CC_MDSS_AHB_CLK>, > + <&gcc GCC_DISP_HF_AXI_CLK>; > + clock-names = "byte", > + "byte_intf", > + "pixel", > + "core", > + "iface", > + "bus"; > + > + assigned-clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK_SRC>, > + <&dispcc DISP_CC_MDSS_PCLK0_CLK_SRC>; > + assigned-clock-parents = <&mdss_dsi0_phy 0>, > + <&mdss_dsi0_phy 1>; > + > + operating-points-v2 = <&dsi_opp_table>; > + power-domains = <&rpmhpd SM8150_MMCX>; > + > + phys = <&mdss_dsi0_phy>; > + > + status = "disabled"; > + > + #address-cells = <1>; > + #size-cells = <0>; > + > + ports { > + #address-cells = <1>; > + #size-cells = <0>; > + > + port@0 { > + reg = <0>; > + mdss_dsi0_in: endpoint { > + remote-endpoint = <&dpu_intf1_out>; > + }; > + }; > + > + port@1 { > + reg = <1>; > + mdss_dsi0_out: endpoint { > + }; > + }; > + }; > + > + dsi_opp_table: opp-table { > + compatible = "operating-points-v2"; > + > + opp-187500000 { > + opp-hz = /bits/ 64 <187500000>; > + required-opps = <&rpmhpd_opp_low_svs>; > + }; > + > + opp-300000000 { > + opp-hz = /bits/ 64 <300000000>; > + required-opps = <&rpmhpd_opp_svs>; > + }; > + > + opp-358000000 { > + opp-hz = /bits/ 64 <358000000>; > + required-opps = <&rpmhpd_opp_svs_l1>; > + }; > + }; > + }; > + > + mdss_dsi0_phy: phy@ae94400 { > + compatible = "qcom,dsi-phy-7nm"; > + reg = <0 0x0ae94400 0 0x200>, > + <0 0x0ae94600 0 0x280>, > + <0 0x0ae94900 0 0x260>; > + reg-names = "dsi_phy", > + "dsi_phy_lane", > + "dsi_pll"; > + > + #clock-cells = <1>; > + #phy-cells = <0>; > + > + clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>, > + <&rpmhcc RPMH_CXO_CLK>; > + clock-names = "iface", "ref"; > + > + status = "disabled"; > + }; > + > + mdss_dsi1: dsi@ae96000 { > + compatible = "qcom,mdss-dsi-ctrl"; > + reg = <0 0x0ae96000 0 0x400>; > + reg-names = "dsi_ctrl"; > + > + interrupt-parent = <&mdss>; > + interrupts = <5>; > + > + clocks = <&dispcc DISP_CC_MDSS_BYTE1_CLK>, > + <&dispcc DISP_CC_MDSS_BYTE1_INTF_CLK>, > + <&dispcc DISP_CC_MDSS_PCLK1_CLK>, > + <&dispcc DISP_CC_MDSS_ESC1_CLK>, > + <&dispcc DISP_CC_MDSS_AHB_CLK>, > + <&gcc GCC_DISP_HF_AXI_CLK>; > + clock-names = "byte", > + "byte_intf", > + "pixel", > + "core", > + "iface", > + "bus"; > + > + assigned-clocks = <&dispcc DISP_CC_MDSS_BYTE1_CLK_SRC>, > + <&dispcc DISP_CC_MDSS_PCLK1_CLK_SRC>; > + assigned-clock-parents = <&mdss_dsi1_phy 0>, > + <&mdss_dsi1_phy 1>; > + > + operating-points-v2 = <&dsi_opp_table>; > + power-domains = <&rpmhpd SM8150_MMCX>; > + > + phys = <&mdss_dsi1_phy>; > + > + status = "disabled"; > + > + #address-cells = <1>; > + #size-cells = <0>; > + > + ports { > + #address-cells = <1>; > + #size-cells = <0>; > + > + port@0 { > + reg = <0>; > + mdss_dsi1_in: endpoint { > + remote-endpoint = <&dpu_intf2_out>; > + }; > + }; > + > + port@1 { > + reg = <1>; > + mdss_dsi1_out: endpoint { > + }; > + }; > + }; > + }; > + > + mdss_dsi1_phy: phy@ae96400 { > + compatible = "qcom,dsi-phy-7nm"; > + reg = <0 0x0ae96400 0 0x200>, > + <0 0x0ae96600 0 0x280>, > + <0 0x0ae96900 0 0x260>; > + reg-names = "dsi_phy", > + "dsi_phy_lane", > + "dsi_pll"; > + > + #clock-cells = <1>; > + #phy-cells = <0>; > + > + clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>, > + <&rpmhcc RPMH_CXO_CLK>; > + clock-names = "iface", "ref"; > + > + status = "disabled"; > + }; > + }; > + > dispcc: clock-controller@af00000 { > compatible = "qcom,sm8150-dispcc"; > reg = <0 0x0af00000 0 0x10000>; > clocks = <&rpmhcc RPMH_CXO_CLK>, > - <0>, > - <0>, > - <0>, > - <0>, > + <&mdss_dsi0_phy 0>, > + <&mdss_dsi0_phy 1>, > + <&mdss_dsi1_phy 0>, > + <&mdss_dsi1_phy 1>, > <0>, > <0>; > clock-names = "bi_tcxo", > -- > 2.38.1 >
diff --git a/arch/arm64/boot/dts/qcom/sm8150.dtsi b/arch/arm64/boot/dts/qcom/sm8150.dtsi index ff04397777f4..c0c1e781eb43 100644 --- a/arch/arm64/boot/dts/qcom/sm8150.dtsi +++ b/arch/arm64/boot/dts/qcom/sm8150.dtsi @@ -9,6 +9,7 @@ #include <dt-bindings/power/qcom-rpmpd.h> #include <dt-bindings/soc/qcom,rpmh-rsc.h> #include <dt-bindings/clock/qcom,rpmh.h> +#include <dt-bindings/clock/qcom,dispcc-sm8150.h> #include <dt-bindings/clock/qcom,gcc-sm8150.h> #include <dt-bindings/clock/qcom,gpucc-sm8150.h> #include <dt-bindings/interconnect/qcom,osm-l3.h> @@ -3579,14 +3580,276 @@ camnoc_virt: interconnect@ac00000 { qcom,bcm-voters = <&apps_bcm_voter>; }; + mdss: mdss@ae00000 { + compatible = "qcom,sm8150-mdss"; + reg = <0 0x0ae00000 0 0x1000>; + reg-names = "mdss"; + + interconnects = <&mmss_noc MASTER_MDP_PORT0 &mc_virt SLAVE_EBI_CH0>, + <&mmss_noc MASTER_MDP_PORT1 &mc_virt SLAVE_EBI_CH0>; + interconnect-names = "mdp0-mem", "mdp1-mem"; + + power-domains = <&dispcc MDSS_GDSC>; + + clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>, + <&gcc GCC_DISP_HF_AXI_CLK>, + <&gcc GCC_DISP_SF_AXI_CLK>, + <&dispcc DISP_CC_MDSS_MDP_CLK>; + clock-names = "iface", "bus", "nrt_bus", "core"; + + interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>; + interrupt-controller; + #interrupt-cells = <1>; + + iommus = <&apps_smmu 0x800 0x420>; + + status = "disabled"; + + #address-cells = <2>; + #size-cells = <2>; + ranges; + + mdss_mdp: display-controller@ae01000 { + compatible = "qcom,sm8150-dpu"; + reg = <0 0x0ae01000 0 0x8f000>, + <0 0x0aeb0000 0 0x2008>; + reg-names = "mdp", "vbif"; + + clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>, + <&gcc GCC_DISP_HF_AXI_CLK>, + <&dispcc DISP_CC_MDSS_MDP_CLK>, + <&dispcc DISP_CC_MDSS_VSYNC_CLK>; + clock-names = "iface", "bus", "core", "vsync"; + + assigned-clocks = <&dispcc DISP_CC_MDSS_VSYNC_CLK>; + assigned-clock-rates = <19200000>; + + operating-points-v2 = <&mdp_opp_table>; + power-domains = <&rpmhpd SM8150_MMCX>; + + interrupt-parent = <&mdss>; + interrupts = <0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + dpu_intf1_out: endpoint { + remote-endpoint = <&mdss_dsi0_in>; + }; + }; + + port@1 { + reg = <1>; + dpu_intf2_out: endpoint { + remote-endpoint = <&mdss_dsi1_in>; + }; + }; + }; + + mdp_opp_table: opp-table { + compatible = "operating-points-v2"; + + opp-171428571 { + opp-hz = /bits/ 64 <171428571>; + required-opps = <&rpmhpd_opp_low_svs>; + }; + + opp-300000000 { + opp-hz = /bits/ 64 <300000000>; + required-opps = <&rpmhpd_opp_svs>; + }; + + opp-345000000 { + opp-hz = /bits/ 64 <345000000>; + required-opps = <&rpmhpd_opp_svs_l1>; + }; + + opp-460000000 { + opp-hz = /bits/ 64 <460000000>; + required-opps = <&rpmhpd_opp_nom>; + }; + }; + }; + + mdss_dsi0: dsi@ae94000 { + compatible = "qcom,mdss-dsi-ctrl"; + reg = <0 0x0ae94000 0 0x400>; + reg-names = "dsi_ctrl"; + + interrupt-parent = <&mdss>; + interrupts = <4>; + + clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK>, + <&dispcc DISP_CC_MDSS_BYTE0_INTF_CLK>, + <&dispcc DISP_CC_MDSS_PCLK0_CLK>, + <&dispcc DISP_CC_MDSS_ESC0_CLK>, + <&dispcc DISP_CC_MDSS_AHB_CLK>, + <&gcc GCC_DISP_HF_AXI_CLK>; + clock-names = "byte", + "byte_intf", + "pixel", + "core", + "iface", + "bus"; + + assigned-clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK_SRC>, + <&dispcc DISP_CC_MDSS_PCLK0_CLK_SRC>; + assigned-clock-parents = <&mdss_dsi0_phy 0>, + <&mdss_dsi0_phy 1>; + + operating-points-v2 = <&dsi_opp_table>; + power-domains = <&rpmhpd SM8150_MMCX>; + + phys = <&mdss_dsi0_phy>; + + status = "disabled"; + + #address-cells = <1>; + #size-cells = <0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + mdss_dsi0_in: endpoint { + remote-endpoint = <&dpu_intf1_out>; + }; + }; + + port@1 { + reg = <1>; + mdss_dsi0_out: endpoint { + }; + }; + }; + + dsi_opp_table: opp-table { + compatible = "operating-points-v2"; + + opp-187500000 { + opp-hz = /bits/ 64 <187500000>; + required-opps = <&rpmhpd_opp_low_svs>; + }; + + opp-300000000 { + opp-hz = /bits/ 64 <300000000>; + required-opps = <&rpmhpd_opp_svs>; + }; + + opp-358000000 { + opp-hz = /bits/ 64 <358000000>; + required-opps = <&rpmhpd_opp_svs_l1>; + }; + }; + }; + + mdss_dsi0_phy: phy@ae94400 { + compatible = "qcom,dsi-phy-7nm"; + reg = <0 0x0ae94400 0 0x200>, + <0 0x0ae94600 0 0x280>, + <0 0x0ae94900 0 0x260>; + reg-names = "dsi_phy", + "dsi_phy_lane", + "dsi_pll"; + + #clock-cells = <1>; + #phy-cells = <0>; + + clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>, + <&rpmhcc RPMH_CXO_CLK>; + clock-names = "iface", "ref"; + + status = "disabled"; + }; + + mdss_dsi1: dsi@ae96000 { + compatible = "qcom,mdss-dsi-ctrl"; + reg = <0 0x0ae96000 0 0x400>; + reg-names = "dsi_ctrl"; + + interrupt-parent = <&mdss>; + interrupts = <5>; + + clocks = <&dispcc DISP_CC_MDSS_BYTE1_CLK>, + <&dispcc DISP_CC_MDSS_BYTE1_INTF_CLK>, + <&dispcc DISP_CC_MDSS_PCLK1_CLK>, + <&dispcc DISP_CC_MDSS_ESC1_CLK>, + <&dispcc DISP_CC_MDSS_AHB_CLK>, + <&gcc GCC_DISP_HF_AXI_CLK>; + clock-names = "byte", + "byte_intf", + "pixel", + "core", + "iface", + "bus"; + + assigned-clocks = <&dispcc DISP_CC_MDSS_BYTE1_CLK_SRC>, + <&dispcc DISP_CC_MDSS_PCLK1_CLK_SRC>; + assigned-clock-parents = <&mdss_dsi1_phy 0>, + <&mdss_dsi1_phy 1>; + + operating-points-v2 = <&dsi_opp_table>; + power-domains = <&rpmhpd SM8150_MMCX>; + + phys = <&mdss_dsi1_phy>; + + status = "disabled"; + + #address-cells = <1>; + #size-cells = <0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + mdss_dsi1_in: endpoint { + remote-endpoint = <&dpu_intf2_out>; + }; + }; + + port@1 { + reg = <1>; + mdss_dsi1_out: endpoint { + }; + }; + }; + }; + + mdss_dsi1_phy: phy@ae96400 { + compatible = "qcom,dsi-phy-7nm"; + reg = <0 0x0ae96400 0 0x200>, + <0 0x0ae96600 0 0x280>, + <0 0x0ae96900 0 0x260>; + reg-names = "dsi_phy", + "dsi_phy_lane", + "dsi_pll"; + + #clock-cells = <1>; + #phy-cells = <0>; + + clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>, + <&rpmhcc RPMH_CXO_CLK>; + clock-names = "iface", "ref"; + + status = "disabled"; + }; + }; + dispcc: clock-controller@af00000 { compatible = "qcom,sm8150-dispcc"; reg = <0 0x0af00000 0 0x10000>; clocks = <&rpmhcc RPMH_CXO_CLK>, - <0>, - <0>, - <0>, - <0>, + <&mdss_dsi0_phy 0>, + <&mdss_dsi0_phy 1>, + <&mdss_dsi1_phy 0>, + <&mdss_dsi1_phy 1>, <0>, <0>; clock-names = "bi_tcxo",
Add required nodes for MDSS and hook up provided clocks in DISPCC. This setup is almost identical to 8[23]50. Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org> --- arch/arm64/boot/dts/qcom/sm8150.dtsi | 271 ++++++++++++++++++++++++++- 1 file changed, 267 insertions(+), 4 deletions(-)