| Message ID | 20240403-msm-drm-dsc-dsi-video-upstream-v1-1-db5036443545@linaro.org (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | Add DSC support to DSI video panel | expand |
On Wed, 3 Apr 2024 at 12:11, Jun Nie <jun.nie@linaro.org> wrote: > > From: Jonathan Marek <jonathan@marek.ca> > > Add necessary DPU timing and control changes for DSC to work with DSI > video mode. > > Signed-off-by: Jonathan Marek <jonathan@marek.ca> > Signed-off-by: Jun Nie <jun.nie@linaro.org> > --- > drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c | 9 +++++++++ > drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c | 8 ++++++++ > 2 files changed, 17 insertions(+) > > diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c > index d9e7dbf0499c..c7b009a60b63 100644 > --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c > +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c > @@ -115,6 +115,15 @@ static void drm_mode_to_intf_timing_params( > timing->h_front_porch = timing->h_front_porch >> 1; > timing->hsync_pulse_width = timing->hsync_pulse_width >> 1; > } > + > + /* > + * for DSI, if compression is enabled, then divide the horizonal active > + * timing parameters by compression ratio. > + */ > + if (phys_enc->hw_intf->cap->type != INTF_DP && timing->compression_en) { > + timing->width = timing->width / 3; /* XXX: don't assume 3:1 compression ratio */ > + timing->xres = timing->width; > + } > } > > static u32 get_horizontal_total(const struct dpu_hw_intf_timing_params *timing) > diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c > index 965692ef7892..079efb48db05 100644 > --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c > +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c > @@ -167,6 +167,14 @@ static void dpu_hw_intf_setup_timing_engine(struct dpu_hw_intf *ctx, > intf_cfg2 |= INTF_CFG2_DATABUS_WIDEN; > > data_width = p->width; > + if (p->wide_bus_en && !dp_intf) > + data_width = p->width >> 1; How is wide_bus relevant to the DSC case? Is there a need for the Fixes tag? > + > + if (p->compression_en) > + intf_cfg2 |= INTF_CFG2_DCE_DATA_COMPRESS; > + > + if (p->compression_en && dp_intf) > + DPU_ERROR("missing adjustments for DSC+DP\n"); > > hsync_data_start_x = hsync_start_x; > hsync_data_end_x = hsync_start_x + data_width - 1; > > -- > 2.34.1 >
Dmitry Baryshkov <dmitry.baryshkov@linaro.org> 于2024年4月3日周三 17:57写道： > > On Wed, 3 Apr 2024 at 12:11, Jun Nie <jun.nie@linaro.org> wrote: > > > > From: Jonathan Marek <jonathan@marek.ca> > > > > Add necessary DPU timing and control changes for DSC to work with DSI > > video mode. > > > > Signed-off-by: Jonathan Marek <jonathan@marek.ca> > > Signed-off-by: Jun Nie <jun.nie@linaro.org> > > --- > > drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c | 9 +++++++++ > > drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c | 8 ++++++++ > > 2 files changed, 17 insertions(+) > > > > diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c > > index d9e7dbf0499c..c7b009a60b63 100644 > > --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c > > +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c > > @@ -115,6 +115,15 @@ static void drm_mode_to_intf_timing_params( > > timing->h_front_porch = timing->h_front_porch >> 1; > > timing->hsync_pulse_width = timing->hsync_pulse_width >> 1; > > } > > + > > + /* > > + * for DSI, if compression is enabled, then divide the horizonal active > > + * timing parameters by compression ratio. > > + */ > > + if (phys_enc->hw_intf->cap->type != INTF_DP && timing->compression_en) { > > + timing->width = timing->width / 3; /* XXX: don't assume 3:1 compression ratio */ > > + timing->xres = timing->width; > > + } > > } > > > > static u32 get_horizontal_total(const struct dpu_hw_intf_timing_params *timing) > > diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c > > index 965692ef7892..079efb48db05 100644 > > --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c > > +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c > > @@ -167,6 +167,14 @@ static void dpu_hw_intf_setup_timing_engine(struct dpu_hw_intf *ctx, > > intf_cfg2 |= INTF_CFG2_DATABUS_WIDEN; > > > > data_width = p->width; > > + if (p->wide_bus_en && !dp_intf) > > + data_width = p->width >> 1; > > How is wide_bus relevant to the DSC case? > Is there a need for the Fixes tag? 48bit bus width should be used when DSC is enabled. Without the widebus configuration, a lot dsi error happens as below in DSC case. [ 206.275992] dsi_err_worker: status=4 For the Fixes tag, the previous patch mentioned to enable the widebus mode for any DSC case. So it is fair to add the tag. > > > + > > + if (p->compression_en) > > + intf_cfg2 |= INTF_CFG2_DCE_DATA_COMPRESS; > > + > > + if (p->compression_en && dp_intf) > > + DPU_ERROR("missing adjustments for DSC+DP\n"); > > > > hsync_data_start_x = hsync_start_x; > > hsync_data_end_x = hsync_start_x + data_width - 1; > > > > -- > > 2.34.1 > > > > > -- > With best wishes > Dmitry
On Wed, 3 Apr 2024 at 17:44, Jun Nie <jun.nie@linaro.org> wrote: > > Dmitry Baryshkov <dmitry.baryshkov@linaro.org> 于2024年4月3日周三 17:57写道： > > > > On Wed, 3 Apr 2024 at 12:11, Jun Nie <jun.nie@linaro.org> wrote: > > > > > > From: Jonathan Marek <jonathan@marek.ca> > > > > > > Add necessary DPU timing and control changes for DSC to work with DSI > > > video mode. > > > > > > Signed-off-by: Jonathan Marek <jonathan@marek.ca> > > > Signed-off-by: Jun Nie <jun.nie@linaro.org> > > > --- > > > drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c | 9 +++++++++ > > > drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c | 8 ++++++++ > > > 2 files changed, 17 insertions(+) > > > > > > diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c > > > index d9e7dbf0499c..c7b009a60b63 100644 > > > --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c > > > +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c > > > @@ -115,6 +115,15 @@ static void drm_mode_to_intf_timing_params( > > > timing->h_front_porch = timing->h_front_porch >> 1; > > > timing->hsync_pulse_width = timing->hsync_pulse_width >> 1; > > > } > > > + > > > + /* > > > + * for DSI, if compression is enabled, then divide the horizonal active > > > + * timing parameters by compression ratio. > > > + */ > > > + if (phys_enc->hw_intf->cap->type != INTF_DP && timing->compression_en) { > > > + timing->width = timing->width / 3; /* XXX: don't assume 3:1 compression ratio */ > > > + timing->xres = timing->width; > > > + } > > > } > > > > > > static u32 get_horizontal_total(const struct dpu_hw_intf_timing_params *timing) > > > diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c > > > index 965692ef7892..079efb48db05 100644 > > > --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c > > > +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c > > > @@ -167,6 +167,14 @@ static void dpu_hw_intf_setup_timing_engine(struct dpu_hw_intf *ctx, > > > intf_cfg2 |= INTF_CFG2_DATABUS_WIDEN; > > > > > > data_width = p->width; > > > + if (p->wide_bus_en && !dp_intf) > > > + data_width = p->width >> 1; > > > > How is wide_bus relevant to the DSC case? > > Is there a need for the Fixes tag? > > 48bit bus width should be used when DSC is enabled. Without the > widebus configuration, > a lot dsi error happens as below in DSC case. > [ 206.275992] dsi_err_worker: status=4 Still, separate patch please. > > For the Fixes tag, the previous patch mentioned to enable the widebus > mode for any DSC case. So it is fair to add the tag. Yes, please. > > > > > + > > > + if (p->compression_en) > > > + intf_cfg2 |= INTF_CFG2_DCE_DATA_COMPRESS; > > > + > > > + if (p->compression_en && dp_intf) > > > + DPU_ERROR("missing adjustments for DSC+DP\n"); > > > > > > hsync_data_start_x = hsync_start_x; > > > hsync_data_end_x = hsync_start_x + data_width - 1; > > > > > > -- > > > 2.34.1 > > > > > > > > > -- > > With best wishes > > Dmitry
diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c index d9e7dbf0499c..c7b009a60b63 100644 --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c @@ -115,6 +115,15 @@ static void drm_mode_to_intf_timing_params( timing->h_front_porch = timing->h_front_porch >> 1; timing->hsync_pulse_width = timing->hsync_pulse_width >> 1; } + + /* + * for DSI, if compression is enabled, then divide the horizonal active + * timing parameters by compression ratio. + */ + if (phys_enc->hw_intf->cap->type != INTF_DP && timing->compression_en) { + timing->width = timing->width / 3; /* XXX: don't assume 3:1 compression ratio */ + timing->xres = timing->width; + } } static u32 get_horizontal_total(const struct dpu_hw_intf_timing_params *timing) diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c index 965692ef7892..079efb48db05 100644 --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c @@ -167,6 +167,14 @@ static void dpu_hw_intf_setup_timing_engine(struct dpu_hw_intf *ctx, intf_cfg2 |= INTF_CFG2_DATABUS_WIDEN; data_width = p->width; + if (p->wide_bus_en && !dp_intf) + data_width = p->width >> 1; + + if (p->compression_en) + intf_cfg2 |= INTF_CFG2_DCE_DATA_COMPRESS; + + if (p->compression_en && dp_intf) + DPU_ERROR("missing adjustments for DSC+DP\n"); hsync_data_start_x = hsync_start_x; hsync_data_end_x = hsync_start_x + data_width - 1;