@@ -279,6 +279,7 @@ struct zynqmp_dp_config {
* @dpsub: Display subsystem
* @iomem: device I/O memory for register access
* @reset: reset controller
+ * @lock: Mutex protecting this struct and register access (but not AUX)
* @irq: irq
* @bridge: DRM bridge for the DP encoder
* @next_bridge: The downstream bridge
@@ -293,11 +294,16 @@ struct zynqmp_dp_config {
* @link_config: common link configuration between IP core and sink device
* @mode: current mode between IP core and sink device
* @train_set: set of training data
+ *
+ * @lock covers the link configuration in this struct and the device's
+ * registers. It does not cover @aux. It is not strictly required for any of
+ * the members which are only modified at probe/remove time (e.g. @dev).
*/
struct zynqmp_dp {
struct drm_dp_aux aux;
struct drm_bridge bridge;
struct work_struct hpd_work;
+ struct mutex lock;
struct drm_bridge *next_bridge;
struct device *dev;
@@ -1371,8 +1377,10 @@ zynqmp_dp_bridge_mode_valid(struct drm_bridge *bridge,
}
/* Check with link rate and lane count */
+ mutex_lock(&dp->lock);
rate = zynqmp_dp_max_rate(dp->link_config.max_rate,
dp->link_config.max_lanes, dp->config.bpp);
+ mutex_unlock(&dp->lock);
if (mode->clock > rate) {
dev_dbg(dp->dev, "filtered mode %s for high pixel rate\n",
mode->name);
@@ -1399,6 +1407,7 @@ static void zynqmp_dp_bridge_atomic_enable(struct drm_bridge *bridge,
pm_runtime_get_sync(dp->dev);
+ mutex_lock(&dp->lock);
zynqmp_dp_disp_enable(dp, old_bridge_state);
/*
@@ -1459,6 +1468,7 @@ static void zynqmp_dp_bridge_atomic_enable(struct drm_bridge *bridge,
zynqmp_dp_write(dp, ZYNQMP_DP_SOFTWARE_RESET,
ZYNQMP_DP_SOFTWARE_RESET_ALL);
zynqmp_dp_write(dp, ZYNQMP_DP_MAIN_STREAM_ENABLE, 1);
+ mutex_unlock(&dp->lock);
}
static void zynqmp_dp_bridge_atomic_disable(struct drm_bridge *bridge,
@@ -1466,6 +1476,7 @@ static void zynqmp_dp_bridge_atomic_disable(struct drm_bridge *bridge,
{
struct zynqmp_dp *dp = bridge_to_dp(bridge);
+ mutex_lock(&dp->lock);
dp->enabled = false;
cancel_work(&dp->hpd_work);
zynqmp_dp_write(dp, ZYNQMP_DP_MAIN_STREAM_ENABLE, 0);
@@ -1476,6 +1487,7 @@ static void zynqmp_dp_bridge_atomic_disable(struct drm_bridge *bridge,
zynqmp_dp_write(dp, ZYNQMP_DP_TX_AUDIO_CONTROL, 0);
zynqmp_dp_disp_disable(dp, old_bridge_state);
+ mutex_unlock(&dp->lock);
pm_runtime_put_sync(dp->dev);
}
@@ -1518,6 +1530,8 @@ static enum drm_connector_status zynqmp_dp_bridge_detect(struct drm_bridge *brid
u32 state, i;
int ret;
+ mutex_lock(&dp->lock);
+
/*
* This is from heuristic. It takes some delay (ex, 100 ~ 500 msec) to
* get the HPD signal with some monitors.
@@ -1545,11 +1559,13 @@ static enum drm_connector_status zynqmp_dp_bridge_detect(struct drm_bridge *brid
dp->num_lanes);
dp->status = connector_status_connected;
+ mutex_unlock(&dp->lock);
return connector_status_connected;
}
disconnected:
dp->status = connector_status_disconnected;
+ mutex_unlock(&dp->lock);
return connector_status_disconnected;
}
@@ -1680,6 +1696,7 @@ int zynqmp_dp_probe(struct zynqmp_dpsub *dpsub)
dp->dev = &pdev->dev;
dp->dpsub = dpsub;
dp->status = connector_status_disconnected;
+ mutex_init(&dp->lock);
INIT_WORK(&dp->hpd_work, zynqmp_dp_hpd_work_func);
@@ -1793,4 +1810,5 @@ void zynqmp_dp_remove(struct zynqmp_dpsub *dpsub)
zynqmp_dp_phy_exit(dp);
zynqmp_dp_reset(dp, true);
+ mutex_destroy(&dp->lock);
}
Add some locking to prevent the IRQ/workers/bridge API calls from stepping on each other's toes. This lock protects: - Non-atomic registers configuring the link. That is, everything but the IRQ registers (since these are accessed in an atomic fashion), and the DP AUX registers (since these don't affect the link). We also access AUX while holding this lock, so it would be very tricky to support. - Link configuration. This is effectively everything in zynqmp_dp which isn't read-only after probe time. So from next_bridge onward. This lock is designed to protect configuration changes so we don't have to do anything tricky. Configuration should never be in the hot path, so I'm not worried about performance. Signed-off-by: Sean Anderson <sean.anderson@linux.dev> --- (no changes since v2) Changes in v2: - Split off the HPD IRQ work into another commit - Expand the commit message drivers/gpu/drm/xlnx/zynqmp_dp.c | 18 ++++++++++++++++++ 1 file changed, 18 insertions(+)