| Message ID | d23737053c54d4c6f9a05da12e807264298a3063.1623725300.git.xji@analogixsemi.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | Add MIPI rx DPI support | expand |
On 16/06/2021 09:50, Xin Ji wrote: > The basic anx7625 driver only support MIPI DSI rx signal input. > This patch add MIPI DPI rx input configuration support, after apply > this patch, the driver can support DSI rx or DPI rx by adding > 'bus-type' in DT. > > Reviewed-by: Robert Foss <robert.foss@linaro.org> > Signed-off-by: Xin Ji <xji@analogixsemi.com> > --- > drivers/gpu/drm/bridge/analogix/anx7625.c | 245 ++++++++++++++++------ > drivers/gpu/drm/bridge/analogix/anx7625.h | 18 +- > 2 files changed, 203 insertions(+), 60 deletions(-) > > diff --git a/drivers/gpu/drm/bridge/analogix/anx7625.c b/drivers/gpu/drm/bridge/analogix/anx7625.c > index 048080e75016..fb2301a92704 100644 > --- a/drivers/gpu/drm/bridge/analogix/anx7625.c > +++ b/drivers/gpu/drm/bridge/analogix/anx7625.c > @@ -152,18 +152,18 @@ static int anx7625_write_and(struct anx7625_data *ctx, > return anx7625_reg_write(ctx, client, offset, (val & (mask))); > } > > -static int anx7625_write_and_or(struct anx7625_data *ctx, > - struct i2c_client *client, > - u8 offset, u8 and_mask, u8 or_mask) > +static int anx7625_config_bit_matrix(struct anx7625_data *ctx) > { > - int val; > + int i, ret; > > - val = anx7625_reg_read(ctx, client, offset); > - if (val < 0) > - return val; > + ret = anx7625_write_or(ctx, ctx->i2c.tx_p2_client, > + AUDIO_CONTROL_REGISTER, 0x80); > + for (i = 0; i < 13; i++) > + ret |= anx7625_reg_write(ctx, ctx->i2c.tx_p2_client, > + VIDEO_BIT_MATRIX_12 + i, > + 0x18 + i); > > - return anx7625_reg_write(ctx, client, > - offset, (val & and_mask) | (or_mask)); > + return ret; > } > > static int anx7625_read_ctrl_status_p0(struct anx7625_data *ctx) > @@ -221,38 +221,6 @@ static int anx7625_video_mute_control(struct anx7625_data *ctx, > return ret; > } > > -static int anx7625_config_audio_input(struct anx7625_data *ctx) > -{ > - struct device *dev = &ctx->client->dev; > - int ret; > - > - /* Channel num */ > - ret = anx7625_reg_write(ctx, ctx->i2c.tx_p2_client, > - AUDIO_CHANNEL_STATUS_6, I2S_CH_2 << 5); > - > - /* FS */ > - ret |= anx7625_write_and_or(ctx, ctx->i2c.tx_p2_client, > - AUDIO_CHANNEL_STATUS_4, > - 0xf0, AUDIO_FS_48K); > - /* Word length */ > - ret |= anx7625_write_and_or(ctx, ctx->i2c.tx_p2_client, > - AUDIO_CHANNEL_STATUS_5, > - 0xf0, AUDIO_W_LEN_24_24MAX); > - /* I2S */ > - ret |= anx7625_write_or(ctx, ctx->i2c.tx_p2_client, > - AUDIO_CHANNEL_STATUS_6, I2S_SLAVE_MODE); > - ret |= anx7625_write_and(ctx, ctx->i2c.tx_p2_client, > - AUDIO_CONTROL_REGISTER, ~TDM_TIMING_MODE); > - /* Audio change flag */ > - ret |= anx7625_write_or(ctx, ctx->i2c.rx_p0_client, > - AP_AV_STATUS, AP_AUDIO_CHG); > - > - if (ret < 0) > - DRM_DEV_ERROR(dev, "fail to config audio.\n"); > - > - return ret; > -} > - > /* Reduction of fraction a/b */ > static void anx7625_reduction_of_a_fraction(unsigned long *a, unsigned long *b) > { > @@ -412,7 +380,7 @@ static int anx7625_dsi_video_timing_config(struct anx7625_data *ctx) > ret |= anx7625_write_and(ctx, ctx->i2c.rx_p1_client, > MIPI_LANE_CTRL_0, 0xfc); > ret |= anx7625_write_or(ctx, ctx->i2c.rx_p1_client, > - MIPI_LANE_CTRL_0, 3); > + MIPI_LANE_CTRL_0, ctx->pdata.mipi_lanes - 1); > > /* Htotal */ > htotal = ctx->dt.hactive.min + ctx->dt.hfront_porch.min + > @@ -597,6 +565,76 @@ static int anx7625_dsi_config(struct anx7625_data *ctx) > return ret; > } > > +static int anx7625_api_dpi_config(struct anx7625_data *ctx) > +{ > + struct device *dev = &ctx->client->dev; > + u16 freq = ctx->dt.pixelclock.min / 1000; > + int ret; > + > + /* configure pixel clock */ > + ret = anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, > + PIXEL_CLOCK_L, freq & 0xFF); > + ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, > + PIXEL_CLOCK_H, (freq >> 8)); > + > + /* set DPI mode */ > + /* set to DPI PLL module sel */ > + ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client, > + MIPI_DIGITAL_PLL_9, 0x20); > + /* power down MIPI */ > + ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client, > + MIPI_LANE_CTRL_10, 0x08); > + /* enable DPI mode */ > + ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client, > + MIPI_DIGITAL_PLL_18, 0x1C); > + /* set first edge */ > + ret |= anx7625_reg_write(ctx, ctx->i2c.tx_p2_client, > + VIDEO_CONTROL_0, 0x06); > + if (ret < 0) > + DRM_DEV_ERROR(dev, "IO error : dpi phy set failed.\n"); > + > + return ret; > +} > + > +static int anx7625_dpi_config(struct anx7625_data *ctx) > +{ > + struct device *dev = &ctx->client->dev; > + int ret; > + > + DRM_DEV_DEBUG_DRIVER(dev, "config dpi\n"); > + > + /* DSC disable */ > + ret = anx7625_write_and(ctx, ctx->i2c.rx_p0_client, > + R_DSC_CTRL_0, ~DSC_EN); > + if (ret < 0) { > + DRM_DEV_ERROR(dev, "IO error : disable dsc failed.\n"); > + return ret; > + } > + > + ret = anx7625_config_bit_matrix(ctx); > + if (ret < 0) { > + DRM_DEV_ERROR(dev, "config bit matrix failed.\n"); > + return ret; > + } > + > + ret = anx7625_api_dpi_config(ctx); > + if (ret < 0) { > + DRM_DEV_ERROR(dev, "mipi phy(dpi) setup failed.\n"); > + return ret; > + } > + > + /* set MIPI RX EN */ > + ret = anx7625_write_or(ctx, ctx->i2c.rx_p0_client, > + AP_AV_STATUS, AP_MIPI_RX_EN); > + /* clear mute flag */ > + ret |= anx7625_write_and(ctx, ctx->i2c.rx_p0_client, > + AP_AV_STATUS, (u8)~AP_MIPI_MUTE); > + if (ret < 0) > + DRM_DEV_ERROR(dev, "IO error : enable mipi rx failed.\n"); > + > + return ret; > +} > + > static void anx7625_dp_start(struct anx7625_data *ctx) > { > int ret; > @@ -607,9 +645,10 @@ static void anx7625_dp_start(struct anx7625_data *ctx) > return; > } > > - anx7625_config_audio_input(ctx); > - > - ret = anx7625_dsi_config(ctx); > + if (ctx->pdata.is_dpi) > + ret = anx7625_dpi_config(ctx); > + else > + ret = anx7625_dsi_config(ctx); > > if (ret < 0) > DRM_DEV_ERROR(dev, "MIPI phy setup error.\n"); > @@ -1047,6 +1086,7 @@ static void anx7625_start_dp_work(struct anx7625_data *ctx) > return; > } > > + ctx->hpd_status = 1; > ctx->hpd_high_cnt++; > > /* Not support HDCP */ > @@ -1056,8 +1096,10 @@ static void anx7625_start_dp_work(struct anx7625_data *ctx) > ret |= anx7625_write_or(ctx, ctx->i2c.rx_p1_client, 0xec, 0x10); > /* Interrupt for DRM */ > ret |= anx7625_write_or(ctx, ctx->i2c.rx_p1_client, 0xff, 0x01); > - if (ret < 0) > + if (ret < 0) { > + DRM_DEV_ERROR(dev, "fail to setting HDCP/auth\n"); > return; > + } > > ret = anx7625_reg_read(ctx, ctx->i2c.rx_p1_client, 0x86); > if (ret < 0) > @@ -1076,6 +1118,10 @@ static void anx7625_hpd_polling(struct anx7625_data *ctx) > int ret, val; > struct device *dev = &ctx->client->dev; > > + /* Interrupt mode, no need poll HPD status, just return */ > + if (ctx->pdata.intp_irq) > + return; > + > ret = readx_poll_timeout(anx7625_read_hpd_status_p0, > ctx, val, > ((val & HPD_STATUS) || (val < 0)), > @@ -1103,6 +1149,21 @@ static void anx7625_remove_edid(struct anx7625_data *ctx) > ctx->slimport_edid_p.edid_block_num = -1; > } > > +static void anx7625_dp_adjust_swing(struct anx7625_data *ctx) > +{ > + int i; > + > + for (i = 0; i < ctx->pdata.dp_lane0_swing_reg_cnt; i++) > + anx7625_reg_write(ctx, ctx->i2c.tx_p1_client, > + DP_TX_LANE0_SWING_REG0 + i, > + ctx->pdata.lane0_reg_data[i] & 0xFF); > + > + for (i = 0; i < ctx->pdata.dp_lane1_swing_reg_cnt; i++) > + anx7625_reg_write(ctx, ctx->i2c.tx_p1_client, > + DP_TX_LANE1_SWING_REG0 + i, > + ctx->pdata.lane1_reg_data[i] & 0xFF); > +} > + > static void dp_hpd_change_handler(struct anx7625_data *ctx, bool on) > { > struct device *dev = &ctx->client->dev; > @@ -1118,9 +1179,8 @@ static void dp_hpd_change_handler(struct anx7625_data *ctx, bool on) > } else { > DRM_DEV_DEBUG_DRIVER(dev, " HPD high\n"); > anx7625_start_dp_work(ctx); > + anx7625_dp_adjust_swing(ctx); > } > - > - ctx->hpd_status = 1; > } > > static int anx7625_hpd_change_detect(struct anx7625_data *ctx) > @@ -1197,20 +1257,72 @@ static irqreturn_t anx7625_intr_hpd_isr(int irq, void *data) > return IRQ_HANDLED; > } > > +static int anx7625_get_swing_setting(struct device *dev, > + struct anx7625_platform_data *pdata) > +{ > + int num_regs; > + > + if (of_get_property(dev->of_node, > + "analogix,lane0-swing", &num_regs)) { > + if (num_regs > DP_TX_SWING_REG_CNT) > + num_regs = DP_TX_SWING_REG_CNT; > + > + pdata->dp_lane0_swing_reg_cnt = num_regs; > + of_property_read_u32_array(dev->of_node, "analogix,lane0-swing", > + pdata->lane0_reg_data, num_regs); > + } > + > + if (of_get_property(dev->of_node, > + "analogix,lane1-swing", &num_regs)) { > + if (num_regs > DP_TX_SWING_REG_CNT) > + num_regs = DP_TX_SWING_REG_CNT; > + > + pdata->dp_lane1_swing_reg_cnt = num_regs; > + of_property_read_u32_array(dev->of_node, "analogix,lane1-swing", > + pdata->lane1_reg_data, num_regs); > + } > + > + return 0; > +} > + > static int anx7625_parse_dt(struct device *dev, > struct anx7625_platform_data *pdata) > { > - struct device_node *np = dev->of_node; > + struct device_node *np = dev->of_node, *ep0; > struct drm_panel *panel; > int ret; > + int bus_type, mipi_lanes; > > + anx7625_get_swing_setting(dev, pdata); > + > + pdata->is_dpi = 1; /* default dpi mode */ > pdata->mipi_host_node = of_graph_get_remote_node(np, 0, 0); > if (!pdata->mipi_host_node) { > DRM_DEV_ERROR(dev, "fail to get internal panel.\n"); > return -ENODEV; > } > > - DRM_DEV_DEBUG_DRIVER(dev, "found dsi host node.\n"); > + bus_type = 5; > + mipi_lanes = MAX_LANES_SUPPORT; > + ep0 = of_graph_get_endpoint_by_regs(np, 0, 0); > + if (ep0) { > + if (of_property_read_u32(ep0, "bus-type", &bus_type)) > + bus_type = 0; > + > + mipi_lanes = of_property_count_u32_elems(ep0, "data-lanes"); > + } > + > + if (bus_type == 5) /* bus type is Parallel(DSI) */ > + pdata->is_dpi = 0; Maybe you can use the include/media/v4l2-fwnode.h V4L2_FWNODE_BUS_TYPE_ defines here instead. Neil > + > + pdata->mipi_lanes = mipi_lanes; > + if (pdata->mipi_lanes > MAX_LANES_SUPPORT || pdata->mipi_lanes <= 0) > + pdata->mipi_lanes = MAX_LANES_SUPPORT; > + > + if (pdata->is_dpi) > + DRM_DEV_DEBUG_DRIVER(dev, "found MIPI DPI host node.\n"); > + else > + DRM_DEV_DEBUG_DRIVER(dev, "found MIPI DSI host node.\n"); > > ret = drm_of_find_panel_or_bridge(np, 1, 0, &panel, NULL); > if (ret < 0) { > @@ -1273,9 +1385,13 @@ static enum drm_connector_status anx7625_sink_detect(struct anx7625_data *ctx) > { > struct device *dev = &ctx->client->dev; > > - DRM_DEV_DEBUG_DRIVER(dev, "sink detect, return connected\n"); > + DRM_DEV_DEBUG_DRIVER(dev, "sink detect\n"); > + > + if (ctx->pdata.panel_bridge) > + return connector_status_connected; > > - return connector_status_connected; > + return ctx->hpd_status ? connector_status_connected : > + connector_status_disconnected; > } > > static int anx7625_attach_dsi(struct anx7625_data *ctx) > @@ -1303,7 +1419,7 @@ static int anx7625_attach_dsi(struct anx7625_data *ctx) > return -EINVAL; > } > > - dsi->lanes = 4; > + dsi->lanes = ctx->pdata.mipi_lanes; > dsi->format = MIPI_DSI_FMT_RGB888; > dsi->mode_flags = MIPI_DSI_MODE_VIDEO | > MIPI_DSI_MODE_VIDEO_SYNC_PULSE | > @@ -1349,10 +1465,12 @@ static int anx7625_bridge_attach(struct drm_bridge *bridge, > return -ENODEV; > } > > - err = anx7625_attach_dsi(ctx); > - if (err) { > - DRM_DEV_ERROR(dev, "Fail to attach to dsi : %d\n", err); > - return err; > + if (!ctx->pdata.is_dpi) { > + err = anx7625_attach_dsi(ctx); > + if (err) { > + DRM_DEV_ERROR(dev, "Fail to attach to dsi : %d\n", err); > + return err; > + } > } > > if (ctx->pdata.panel_bridge) { > @@ -1451,6 +1569,10 @@ static bool anx7625_bridge_mode_fixup(struct drm_bridge *bridge, > > DRM_DEV_DEBUG_DRIVER(dev, "drm mode fixup set\n"); > > + /* No need fixup for external monitor */ > + if (!ctx->pdata.panel_bridge) > + return true; > + > hsync = mode->hsync_end - mode->hsync_start; > hfp = mode->hsync_start - mode->hdisplay; > hbp = mode->htotal - mode->hsync_end; > @@ -1827,8 +1949,13 @@ static int anx7625_i2c_probe(struct i2c_client *client, > > platform->bridge.funcs = &anx7625_bridge_funcs; > platform->bridge.of_node = client->dev.of_node; > - platform->bridge.ops = DRM_BRIDGE_OP_EDID | DRM_BRIDGE_OP_HPD; > - platform->bridge.type = DRM_MODE_CONNECTOR_eDP; > + platform->bridge.ops = DRM_BRIDGE_OP_EDID; > + if (!platform->pdata.panel_bridge) > + platform->bridge.ops |= DRM_BRIDGE_OP_HPD | > + DRM_BRIDGE_OP_DETECT; > + platform->bridge.type = platform->pdata.panel_bridge ? > + DRM_MODE_CONNECTOR_eDP : > + DRM_MODE_CONNECTOR_DisplayPort; > drm_bridge_add(&platform->bridge); > > DRM_DEV_DEBUG_DRIVER(dev, "probe done\n"); > diff --git a/drivers/gpu/drm/bridge/analogix/anx7625.h b/drivers/gpu/drm/bridge/analogix/anx7625.h > index 034c3840028f..65db38e5da9a 100644 > --- a/drivers/gpu/drm/bridge/analogix/anx7625.h > +++ b/drivers/gpu/drm/bridge/analogix/anx7625.h > @@ -141,12 +141,20 @@ > #define HORIZONTAL_BACK_PORCH_H 0x22 /* Bit[7:4] are reserved */ > > /******** END of I2C Address 0x72 *********/ > + > +/***************************************************************/ > +/* Register definition of device address 0x7a */ > +#define DP_TX_SWING_REG_CNT 0x14 > +#define DP_TX_LANE0_SWING_REG0 0x00 > +#define DP_TX_LANE1_SWING_REG0 0x14 > +/******** END of I2C Address 0x7a *********/ > + > /***************************************************************/ > /* Register definition of device address 0x7e */ > > #define I2C_ADDR_7E_FLASH_CONTROLLER 0x7E > > -#define FLASH_LOAD_STA 0x05 > +#define FLASH_LOAD_STA 0x05 > #define FLASH_LOAD_STA_CHK BIT(7) > > #define XTAL_FRQ_SEL 0x3F > @@ -347,12 +355,20 @@ struct s_edid_data { > > /***************** Display End *****************/ > > +#define MAX_LANES_SUPPORT 4 > + > struct anx7625_platform_data { > struct gpio_desc *gpio_p_on; > struct gpio_desc *gpio_reset; > struct regulator_bulk_data supplies[3]; > struct drm_bridge *panel_bridge; > int intp_irq; > + int is_dpi; > + int mipi_lanes; > + int dp_lane0_swing_reg_cnt; > + int lane0_reg_data[DP_TX_SWING_REG_CNT]; > + int dp_lane1_swing_reg_cnt; > + int lane1_reg_data[DP_TX_SWING_REG_CNT]; > u32 low_power_mode; > struct device_node *mipi_host_node; > }; >
On Wed, Jun 16, 2021 at 11:16:14AM +0200, Neil Armstrong wrote: > On 16/06/2021 09:50, Xin Ji wrote: > > The basic anx7625 driver only support MIPI DSI rx signal input. > > This patch add MIPI DPI rx input configuration support, after apply > > this patch, the driver can support DSI rx or DPI rx by adding > > 'bus-type' in DT. > > > > Reviewed-by: Robert Foss <robert.foss@linaro.org> > > Signed-off-by: Xin Ji <xji@analogixsemi.com> > > --- > > drivers/gpu/drm/bridge/analogix/anx7625.c | 245 ++++++++++++++++------ > > drivers/gpu/drm/bridge/analogix/anx7625.h | 18 +- > > 2 files changed, 203 insertions(+), 60 deletions(-) > > > > diff --git a/drivers/gpu/drm/bridge/analogix/anx7625.c b/drivers/gpu/drm/bridge/analogix/anx7625.c > > index 048080e75016..fb2301a92704 100644 > > --- a/drivers/gpu/drm/bridge/analogix/anx7625.c > > +++ b/drivers/gpu/drm/bridge/analogix/anx7625.c > > @@ -152,18 +152,18 @@ static int anx7625_write_and(struct anx7625_data *ctx, > > return anx7625_reg_write(ctx, client, offset, (val & (mask))); > > } > > > > -static int anx7625_write_and_or(struct anx7625_data *ctx, > > - struct i2c_client *client, > > - u8 offset, u8 and_mask, u8 or_mask) > > +static int anx7625_config_bit_matrix(struct anx7625_data *ctx) > > { > > - int val; > > + int i, ret; > > > > - val = anx7625_reg_read(ctx, client, offset); > > - if (val < 0) > > - return val; > > + ret = anx7625_write_or(ctx, ctx->i2c.tx_p2_client, > > + AUDIO_CONTROL_REGISTER, 0x80); > > + for (i = 0; i < 13; i++) > > + ret |= anx7625_reg_write(ctx, ctx->i2c.tx_p2_client, > > + VIDEO_BIT_MATRIX_12 + i, > > + 0x18 + i); > > > > - return anx7625_reg_write(ctx, client, > > - offset, (val & and_mask) | (or_mask)); > > + return ret; > > } > > > > static int anx7625_read_ctrl_status_p0(struct anx7625_data *ctx) > > @@ -221,38 +221,6 @@ static int anx7625_video_mute_control(struct anx7625_data *ctx, > > return ret; > > } > > > > -static int anx7625_config_audio_input(struct anx7625_data *ctx) > > -{ > > - struct device *dev = &ctx->client->dev; > > - int ret; > > - > > - /* Channel num */ > > - ret = anx7625_reg_write(ctx, ctx->i2c.tx_p2_client, > > - AUDIO_CHANNEL_STATUS_6, I2S_CH_2 << 5); > > - > > - /* FS */ > > - ret |= anx7625_write_and_or(ctx, ctx->i2c.tx_p2_client, > > - AUDIO_CHANNEL_STATUS_4, > > - 0xf0, AUDIO_FS_48K); > > - /* Word length */ > > - ret |= anx7625_write_and_or(ctx, ctx->i2c.tx_p2_client, > > - AUDIO_CHANNEL_STATUS_5, > > - 0xf0, AUDIO_W_LEN_24_24MAX); > > - /* I2S */ > > - ret |= anx7625_write_or(ctx, ctx->i2c.tx_p2_client, > > - AUDIO_CHANNEL_STATUS_6, I2S_SLAVE_MODE); > > - ret |= anx7625_write_and(ctx, ctx->i2c.tx_p2_client, > > - AUDIO_CONTROL_REGISTER, ~TDM_TIMING_MODE); > > - /* Audio change flag */ > > - ret |= anx7625_write_or(ctx, ctx->i2c.rx_p0_client, > > - AP_AV_STATUS, AP_AUDIO_CHG); > > - > > - if (ret < 0) > > - DRM_DEV_ERROR(dev, "fail to config audio.\n"); > > - > > - return ret; > > -} > > - > > /* Reduction of fraction a/b */ > > static void anx7625_reduction_of_a_fraction(unsigned long *a, unsigned long *b) > > { > > @@ -412,7 +380,7 @@ static int anx7625_dsi_video_timing_config(struct anx7625_data *ctx) > > ret |= anx7625_write_and(ctx, ctx->i2c.rx_p1_client, > > MIPI_LANE_CTRL_0, 0xfc); > > ret |= anx7625_write_or(ctx, ctx->i2c.rx_p1_client, > > - MIPI_LANE_CTRL_0, 3); > > + MIPI_LANE_CTRL_0, ctx->pdata.mipi_lanes - 1); > > > > /* Htotal */ > > htotal = ctx->dt.hactive.min + ctx->dt.hfront_porch.min + > > @@ -597,6 +565,76 @@ static int anx7625_dsi_config(struct anx7625_data *ctx) > > return ret; > > } > > > > +static int anx7625_api_dpi_config(struct anx7625_data *ctx) > > +{ > > + struct device *dev = &ctx->client->dev; > > + u16 freq = ctx->dt.pixelclock.min / 1000; > > + int ret; > > + > > + /* configure pixel clock */ > > + ret = anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, > > + PIXEL_CLOCK_L, freq & 0xFF); > > + ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, > > + PIXEL_CLOCK_H, (freq >> 8)); > > + > > + /* set DPI mode */ > > + /* set to DPI PLL module sel */ > > + ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client, > > + MIPI_DIGITAL_PLL_9, 0x20); > > + /* power down MIPI */ > > + ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client, > > + MIPI_LANE_CTRL_10, 0x08); > > + /* enable DPI mode */ > > + ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client, > > + MIPI_DIGITAL_PLL_18, 0x1C); > > + /* set first edge */ > > + ret |= anx7625_reg_write(ctx, ctx->i2c.tx_p2_client, > > + VIDEO_CONTROL_0, 0x06); > > + if (ret < 0) > > + DRM_DEV_ERROR(dev, "IO error : dpi phy set failed.\n"); > > + > > + return ret; > > +} > > + > > +static int anx7625_dpi_config(struct anx7625_data *ctx) > > +{ > > + struct device *dev = &ctx->client->dev; > > + int ret; > > + > > + DRM_DEV_DEBUG_DRIVER(dev, "config dpi\n"); > > + > > + /* DSC disable */ > > + ret = anx7625_write_and(ctx, ctx->i2c.rx_p0_client, > > + R_DSC_CTRL_0, ~DSC_EN); > > + if (ret < 0) { > > + DRM_DEV_ERROR(dev, "IO error : disable dsc failed.\n"); > > + return ret; > > + } > > + > > + ret = anx7625_config_bit_matrix(ctx); > > + if (ret < 0) { > > + DRM_DEV_ERROR(dev, "config bit matrix failed.\n"); > > + return ret; > > + } > > + > > + ret = anx7625_api_dpi_config(ctx); > > + if (ret < 0) { > > + DRM_DEV_ERROR(dev, "mipi phy(dpi) setup failed.\n"); > > + return ret; > > + } > > + > > + /* set MIPI RX EN */ > > + ret = anx7625_write_or(ctx, ctx->i2c.rx_p0_client, > > + AP_AV_STATUS, AP_MIPI_RX_EN); > > + /* clear mute flag */ > > + ret |= anx7625_write_and(ctx, ctx->i2c.rx_p0_client, > > + AP_AV_STATUS, (u8)~AP_MIPI_MUTE); > > + if (ret < 0) > > + DRM_DEV_ERROR(dev, "IO error : enable mipi rx failed.\n"); > > + > > + return ret; > > +} > > + > > static void anx7625_dp_start(struct anx7625_data *ctx) > > { > > int ret; > > @@ -607,9 +645,10 @@ static void anx7625_dp_start(struct anx7625_data *ctx) > > return; > > } > > > > - anx7625_config_audio_input(ctx); > > - > > - ret = anx7625_dsi_config(ctx); > > + if (ctx->pdata.is_dpi) > > + ret = anx7625_dpi_config(ctx); > > + else > > + ret = anx7625_dsi_config(ctx); > > > > if (ret < 0) > > DRM_DEV_ERROR(dev, "MIPI phy setup error.\n"); > > @@ -1047,6 +1086,7 @@ static void anx7625_start_dp_work(struct anx7625_data *ctx) > > return; > > } > > > > + ctx->hpd_status = 1; > > ctx->hpd_high_cnt++; > > > > /* Not support HDCP */ > > @@ -1056,8 +1096,10 @@ static void anx7625_start_dp_work(struct anx7625_data *ctx) > > ret |= anx7625_write_or(ctx, ctx->i2c.rx_p1_client, 0xec, 0x10); > > /* Interrupt for DRM */ > > ret |= anx7625_write_or(ctx, ctx->i2c.rx_p1_client, 0xff, 0x01); > > - if (ret < 0) > > + if (ret < 0) { > > + DRM_DEV_ERROR(dev, "fail to setting HDCP/auth\n"); > > return; > > + } > > > > ret = anx7625_reg_read(ctx, ctx->i2c.rx_p1_client, 0x86); > > if (ret < 0) > > @@ -1076,6 +1118,10 @@ static void anx7625_hpd_polling(struct anx7625_data *ctx) > > int ret, val; > > struct device *dev = &ctx->client->dev; > > > > + /* Interrupt mode, no need poll HPD status, just return */ > > + if (ctx->pdata.intp_irq) > > + return; > > + > > ret = readx_poll_timeout(anx7625_read_hpd_status_p0, > > ctx, val, > > ((val & HPD_STATUS) || (val < 0)), > > @@ -1103,6 +1149,21 @@ static void anx7625_remove_edid(struct anx7625_data *ctx) > > ctx->slimport_edid_p.edid_block_num = -1; > > } > > > > +static void anx7625_dp_adjust_swing(struct anx7625_data *ctx) > > +{ > > + int i; > > + > > + for (i = 0; i < ctx->pdata.dp_lane0_swing_reg_cnt; i++) > > + anx7625_reg_write(ctx, ctx->i2c.tx_p1_client, > > + DP_TX_LANE0_SWING_REG0 + i, > > + ctx->pdata.lane0_reg_data[i] & 0xFF); > > + > > + for (i = 0; i < ctx->pdata.dp_lane1_swing_reg_cnt; i++) > > + anx7625_reg_write(ctx, ctx->i2c.tx_p1_client, > > + DP_TX_LANE1_SWING_REG0 + i, > > + ctx->pdata.lane1_reg_data[i] & 0xFF); > > +} > > + > > static void dp_hpd_change_handler(struct anx7625_data *ctx, bool on) > > { > > struct device *dev = &ctx->client->dev; > > @@ -1118,9 +1179,8 @@ static void dp_hpd_change_handler(struct anx7625_data *ctx, bool on) > > } else { > > DRM_DEV_DEBUG_DRIVER(dev, " HPD high\n"); > > anx7625_start_dp_work(ctx); > > + anx7625_dp_adjust_swing(ctx); > > } > > - > > - ctx->hpd_status = 1; > > } > > > > static int anx7625_hpd_change_detect(struct anx7625_data *ctx) > > @@ -1197,20 +1257,72 @@ static irqreturn_t anx7625_intr_hpd_isr(int irq, void *data) > > return IRQ_HANDLED; > > } > > > > +static int anx7625_get_swing_setting(struct device *dev, > > + struct anx7625_platform_data *pdata) > > +{ > > + int num_regs; > > + > > + if (of_get_property(dev->of_node, > > + "analogix,lane0-swing", &num_regs)) { > > + if (num_regs > DP_TX_SWING_REG_CNT) > > + num_regs = DP_TX_SWING_REG_CNT; > > + > > + pdata->dp_lane0_swing_reg_cnt = num_regs; > > + of_property_read_u32_array(dev->of_node, "analogix,lane0-swing", > > + pdata->lane0_reg_data, num_regs); > > + } > > + > > + if (of_get_property(dev->of_node, > > + "analogix,lane1-swing", &num_regs)) { > > + if (num_regs > DP_TX_SWING_REG_CNT) > > + num_regs = DP_TX_SWING_REG_CNT; > > + > > + pdata->dp_lane1_swing_reg_cnt = num_regs; > > + of_property_read_u32_array(dev->of_node, "analogix,lane1-swing", > > + pdata->lane1_reg_data, num_regs); > > + } > > + > > + return 0; > > +} > > + > > static int anx7625_parse_dt(struct device *dev, > > struct anx7625_platform_data *pdata) > > { > > - struct device_node *np = dev->of_node; > > + struct device_node *np = dev->of_node, *ep0; > > struct drm_panel *panel; > > int ret; > > + int bus_type, mipi_lanes; > > > > + anx7625_get_swing_setting(dev, pdata); > > + > > + pdata->is_dpi = 1; /* default dpi mode */ > > pdata->mipi_host_node = of_graph_get_remote_node(np, 0, 0); > > if (!pdata->mipi_host_node) { > > DRM_DEV_ERROR(dev, "fail to get internal panel.\n"); > > return -ENODEV; > > } > > > > - DRM_DEV_DEBUG_DRIVER(dev, "found dsi host node.\n"); > > + bus_type = 5; > > + mipi_lanes = MAX_LANES_SUPPORT; > > + ep0 = of_graph_get_endpoint_by_regs(np, 0, 0); > > + if (ep0) { > > + if (of_property_read_u32(ep0, "bus-type", &bus_type)) > > + bus_type = 0; > > + > > + mipi_lanes = of_property_count_u32_elems(ep0, "data-lanes"); > > + } > > + > > + if (bus_type == 5) /* bus type is Parallel(DSI) */ > > + pdata->is_dpi = 0; > > Maybe you can use the include/media/v4l2-fwnode.h V4L2_FWNODE_BUS_TYPE_ defines here instead. > > Neil Hi Neil, OK, I'll use the properly macro instead of fixing value. Thanks, Xin > > > + > > + pdata->mipi_lanes = mipi_lanes; > > + if (pdata->mipi_lanes > MAX_LANES_SUPPORT || pdata->mipi_lanes <= 0) > > + pdata->mipi_lanes = MAX_LANES_SUPPORT; > > + > > + if (pdata->is_dpi) > > + DRM_DEV_DEBUG_DRIVER(dev, "found MIPI DPI host node.\n"); > > + else > > + DRM_DEV_DEBUG_DRIVER(dev, "found MIPI DSI host node.\n"); > > > > ret = drm_of_find_panel_or_bridge(np, 1, 0, &panel, NULL); > > if (ret < 0) { > > @@ -1273,9 +1385,13 @@ static enum drm_connector_status anx7625_sink_detect(struct anx7625_data *ctx) > > { > > struct device *dev = &ctx->client->dev; > > > > - DRM_DEV_DEBUG_DRIVER(dev, "sink detect, return connected\n"); > > + DRM_DEV_DEBUG_DRIVER(dev, "sink detect\n"); > > + > > + if (ctx->pdata.panel_bridge) > > + return connector_status_connected; > > > > - return connector_status_connected; > > + return ctx->hpd_status ? connector_status_connected : > > + connector_status_disconnected; > > } > > > > static int anx7625_attach_dsi(struct anx7625_data *ctx) > > @@ -1303,7 +1419,7 @@ static int anx7625_attach_dsi(struct anx7625_data *ctx) > > return -EINVAL; > > } > > > > - dsi->lanes = 4; > > + dsi->lanes = ctx->pdata.mipi_lanes; > > dsi->format = MIPI_DSI_FMT_RGB888; > > dsi->mode_flags = MIPI_DSI_MODE_VIDEO | > > MIPI_DSI_MODE_VIDEO_SYNC_PULSE | > > @@ -1349,10 +1465,12 @@ static int anx7625_bridge_attach(struct drm_bridge *bridge, > > return -ENODEV; > > } > > > > - err = anx7625_attach_dsi(ctx); > > - if (err) { > > - DRM_DEV_ERROR(dev, "Fail to attach to dsi : %d\n", err); > > - return err; > > + if (!ctx->pdata.is_dpi) { > > + err = anx7625_attach_dsi(ctx); > > + if (err) { > > + DRM_DEV_ERROR(dev, "Fail to attach to dsi : %d\n", err); > > + return err; > > + } > > } > > > > if (ctx->pdata.panel_bridge) { > > @@ -1451,6 +1569,10 @@ static bool anx7625_bridge_mode_fixup(struct drm_bridge *bridge, > > > > DRM_DEV_DEBUG_DRIVER(dev, "drm mode fixup set\n"); > > > > + /* No need fixup for external monitor */ > > + if (!ctx->pdata.panel_bridge) > > + return true; > > + > > hsync = mode->hsync_end - mode->hsync_start; > > hfp = mode->hsync_start - mode->hdisplay; > > hbp = mode->htotal - mode->hsync_end; > > @@ -1827,8 +1949,13 @@ static int anx7625_i2c_probe(struct i2c_client *client, > > > > platform->bridge.funcs = &anx7625_bridge_funcs; > > platform->bridge.of_node = client->dev.of_node; > > - platform->bridge.ops = DRM_BRIDGE_OP_EDID | DRM_BRIDGE_OP_HPD; > > - platform->bridge.type = DRM_MODE_CONNECTOR_eDP; > > + platform->bridge.ops = DRM_BRIDGE_OP_EDID; > > + if (!platform->pdata.panel_bridge) > > + platform->bridge.ops |= DRM_BRIDGE_OP_HPD | > > + DRM_BRIDGE_OP_DETECT; > > + platform->bridge.type = platform->pdata.panel_bridge ? > > + DRM_MODE_CONNECTOR_eDP : > > + DRM_MODE_CONNECTOR_DisplayPort; > > drm_bridge_add(&platform->bridge); > > > > DRM_DEV_DEBUG_DRIVER(dev, "probe done\n"); > > diff --git a/drivers/gpu/drm/bridge/analogix/anx7625.h b/drivers/gpu/drm/bridge/analogix/anx7625.h > > index 034c3840028f..65db38e5da9a 100644 > > --- a/drivers/gpu/drm/bridge/analogix/anx7625.h > > +++ b/drivers/gpu/drm/bridge/analogix/anx7625.h > > @@ -141,12 +141,20 @@ > > #define HORIZONTAL_BACK_PORCH_H 0x22 /* Bit[7:4] are reserved */ > > > > /******** END of I2C Address 0x72 *********/ > > + > > +/***************************************************************/ > > +/* Register definition of device address 0x7a */ > > +#define DP_TX_SWING_REG_CNT 0x14 > > +#define DP_TX_LANE0_SWING_REG0 0x00 > > +#define DP_TX_LANE1_SWING_REG0 0x14 > > +/******** END of I2C Address 0x7a *********/ > > + > > /***************************************************************/ > > /* Register definition of device address 0x7e */ > > > > #define I2C_ADDR_7E_FLASH_CONTROLLER 0x7E > > > > -#define FLASH_LOAD_STA 0x05 > > +#define FLASH_LOAD_STA 0x05 > > #define FLASH_LOAD_STA_CHK BIT(7) > > > > #define XTAL_FRQ_SEL 0x3F > > @@ -347,12 +355,20 @@ struct s_edid_data { > > > > /***************** Display End *****************/ > > > > +#define MAX_LANES_SUPPORT 4 > > + > > struct anx7625_platform_data { > > struct gpio_desc *gpio_p_on; > > struct gpio_desc *gpio_reset; > > struct regulator_bulk_data supplies[3]; > > struct drm_bridge *panel_bridge; > > int intp_irq; > > + int is_dpi; > > + int mipi_lanes; > > + int dp_lane0_swing_reg_cnt; > > + int lane0_reg_data[DP_TX_SWING_REG_CNT]; > > + int dp_lane1_swing_reg_cnt; > > + int lane1_reg_data[DP_TX_SWING_REG_CNT]; > > u32 low_power_mode; > > struct device_node *mipi_host_node; > > }; > >
diff --git a/drivers/gpu/drm/bridge/analogix/anx7625.c b/drivers/gpu/drm/bridge/analogix/anx7625.c index 048080e75016..fb2301a92704 100644 --- a/drivers/gpu/drm/bridge/analogix/anx7625.c +++ b/drivers/gpu/drm/bridge/analogix/anx7625.c @@ -152,18 +152,18 @@ static int anx7625_write_and(struct anx7625_data *ctx, return anx7625_reg_write(ctx, client, offset, (val & (mask))); } -static int anx7625_write_and_or(struct anx7625_data *ctx, - struct i2c_client *client, - u8 offset, u8 and_mask, u8 or_mask) +static int anx7625_config_bit_matrix(struct anx7625_data *ctx) { - int val; + int i, ret; - val = anx7625_reg_read(ctx, client, offset); - if (val < 0) - return val; + ret = anx7625_write_or(ctx, ctx->i2c.tx_p2_client, + AUDIO_CONTROL_REGISTER, 0x80); + for (i = 0; i < 13; i++) + ret |= anx7625_reg_write(ctx, ctx->i2c.tx_p2_client, + VIDEO_BIT_MATRIX_12 + i, + 0x18 + i); - return anx7625_reg_write(ctx, client, - offset, (val & and_mask) | (or_mask)); + return ret; } static int anx7625_read_ctrl_status_p0(struct anx7625_data *ctx) @@ -221,38 +221,6 @@ static int anx7625_video_mute_control(struct anx7625_data *ctx, return ret; } -static int anx7625_config_audio_input(struct anx7625_data *ctx) -{ - struct device *dev = &ctx->client->dev; - int ret; - - /* Channel num */ - ret = anx7625_reg_write(ctx, ctx->i2c.tx_p2_client, - AUDIO_CHANNEL_STATUS_6, I2S_CH_2 << 5); - - /* FS */ - ret |= anx7625_write_and_or(ctx, ctx->i2c.tx_p2_client, - AUDIO_CHANNEL_STATUS_4, - 0xf0, AUDIO_FS_48K); - /* Word length */ - ret |= anx7625_write_and_or(ctx, ctx->i2c.tx_p2_client, - AUDIO_CHANNEL_STATUS_5, - 0xf0, AUDIO_W_LEN_24_24MAX); - /* I2S */ - ret |= anx7625_write_or(ctx, ctx->i2c.tx_p2_client, - AUDIO_CHANNEL_STATUS_6, I2S_SLAVE_MODE); - ret |= anx7625_write_and(ctx, ctx->i2c.tx_p2_client, - AUDIO_CONTROL_REGISTER, ~TDM_TIMING_MODE); - /* Audio change flag */ - ret |= anx7625_write_or(ctx, ctx->i2c.rx_p0_client, - AP_AV_STATUS, AP_AUDIO_CHG); - - if (ret < 0) - DRM_DEV_ERROR(dev, "fail to config audio.\n"); - - return ret; -} - /* Reduction of fraction a/b */ static void anx7625_reduction_of_a_fraction(unsigned long *a, unsigned long *b) { @@ -412,7 +380,7 @@ static int anx7625_dsi_video_timing_config(struct anx7625_data *ctx) ret |= anx7625_write_and(ctx, ctx->i2c.rx_p1_client, MIPI_LANE_CTRL_0, 0xfc); ret |= anx7625_write_or(ctx, ctx->i2c.rx_p1_client, - MIPI_LANE_CTRL_0, 3); + MIPI_LANE_CTRL_0, ctx->pdata.mipi_lanes - 1); /* Htotal */ htotal = ctx->dt.hactive.min + ctx->dt.hfront_porch.min + @@ -597,6 +565,76 @@ static int anx7625_dsi_config(struct anx7625_data *ctx) return ret; } +static int anx7625_api_dpi_config(struct anx7625_data *ctx) +{ + struct device *dev = &ctx->client->dev; + u16 freq = ctx->dt.pixelclock.min / 1000; + int ret; + + /* configure pixel clock */ + ret = anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, + PIXEL_CLOCK_L, freq & 0xFF); + ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, + PIXEL_CLOCK_H, (freq >> 8)); + + /* set DPI mode */ + /* set to DPI PLL module sel */ + ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client, + MIPI_DIGITAL_PLL_9, 0x20); + /* power down MIPI */ + ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client, + MIPI_LANE_CTRL_10, 0x08); + /* enable DPI mode */ + ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p1_client, + MIPI_DIGITAL_PLL_18, 0x1C); + /* set first edge */ + ret |= anx7625_reg_write(ctx, ctx->i2c.tx_p2_client, + VIDEO_CONTROL_0, 0x06); + if (ret < 0) + DRM_DEV_ERROR(dev, "IO error : dpi phy set failed.\n"); + + return ret; +} + +static int anx7625_dpi_config(struct anx7625_data *ctx) +{ + struct device *dev = &ctx->client->dev; + int ret; + + DRM_DEV_DEBUG_DRIVER(dev, "config dpi\n"); + + /* DSC disable */ + ret = anx7625_write_and(ctx, ctx->i2c.rx_p0_client, + R_DSC_CTRL_0, ~DSC_EN); + if (ret < 0) { + DRM_DEV_ERROR(dev, "IO error : disable dsc failed.\n"); + return ret; + } + + ret = anx7625_config_bit_matrix(ctx); + if (ret < 0) { + DRM_DEV_ERROR(dev, "config bit matrix failed.\n"); + return ret; + } + + ret = anx7625_api_dpi_config(ctx); + if (ret < 0) { + DRM_DEV_ERROR(dev, "mipi phy(dpi) setup failed.\n"); + return ret; + } + + /* set MIPI RX EN */ + ret = anx7625_write_or(ctx, ctx->i2c.rx_p0_client, + AP_AV_STATUS, AP_MIPI_RX_EN); + /* clear mute flag */ + ret |= anx7625_write_and(ctx, ctx->i2c.rx_p0_client, + AP_AV_STATUS, (u8)~AP_MIPI_MUTE); + if (ret < 0) + DRM_DEV_ERROR(dev, "IO error : enable mipi rx failed.\n"); + + return ret; +} + static void anx7625_dp_start(struct anx7625_data *ctx) { int ret; @@ -607,9 +645,10 @@ static void anx7625_dp_start(struct anx7625_data *ctx) return; } - anx7625_config_audio_input(ctx); - - ret = anx7625_dsi_config(ctx); + if (ctx->pdata.is_dpi) + ret = anx7625_dpi_config(ctx); + else + ret = anx7625_dsi_config(ctx); if (ret < 0) DRM_DEV_ERROR(dev, "MIPI phy setup error.\n"); @@ -1047,6 +1086,7 @@ static void anx7625_start_dp_work(struct anx7625_data *ctx) return; } + ctx->hpd_status = 1; ctx->hpd_high_cnt++; /* Not support HDCP */ @@ -1056,8 +1096,10 @@ static void anx7625_start_dp_work(struct anx7625_data *ctx) ret |= anx7625_write_or(ctx, ctx->i2c.rx_p1_client, 0xec, 0x10); /* Interrupt for DRM */ ret |= anx7625_write_or(ctx, ctx->i2c.rx_p1_client, 0xff, 0x01); - if (ret < 0) + if (ret < 0) { + DRM_DEV_ERROR(dev, "fail to setting HDCP/auth\n"); return; + } ret = anx7625_reg_read(ctx, ctx->i2c.rx_p1_client, 0x86); if (ret < 0) @@ -1076,6 +1118,10 @@ static void anx7625_hpd_polling(struct anx7625_data *ctx) int ret, val; struct device *dev = &ctx->client->dev; + /* Interrupt mode, no need poll HPD status, just return */ + if (ctx->pdata.intp_irq) + return; + ret = readx_poll_timeout(anx7625_read_hpd_status_p0, ctx, val, ((val & HPD_STATUS) || (val < 0)), @@ -1103,6 +1149,21 @@ static void anx7625_remove_edid(struct anx7625_data *ctx) ctx->slimport_edid_p.edid_block_num = -1; } +static void anx7625_dp_adjust_swing(struct anx7625_data *ctx) +{ + int i; + + for (i = 0; i < ctx->pdata.dp_lane0_swing_reg_cnt; i++) + anx7625_reg_write(ctx, ctx->i2c.tx_p1_client, + DP_TX_LANE0_SWING_REG0 + i, + ctx->pdata.lane0_reg_data[i] & 0xFF); + + for (i = 0; i < ctx->pdata.dp_lane1_swing_reg_cnt; i++) + anx7625_reg_write(ctx, ctx->i2c.tx_p1_client, + DP_TX_LANE1_SWING_REG0 + i, + ctx->pdata.lane1_reg_data[i] & 0xFF); +} + static void dp_hpd_change_handler(struct anx7625_data *ctx, bool on) { struct device *dev = &ctx->client->dev; @@ -1118,9 +1179,8 @@ static void dp_hpd_change_handler(struct anx7625_data *ctx, bool on) } else { DRM_DEV_DEBUG_DRIVER(dev, " HPD high\n"); anx7625_start_dp_work(ctx); + anx7625_dp_adjust_swing(ctx); } - - ctx->hpd_status = 1; } static int anx7625_hpd_change_detect(struct anx7625_data *ctx) @@ -1197,20 +1257,72 @@ static irqreturn_t anx7625_intr_hpd_isr(int irq, void *data) return IRQ_HANDLED; } +static int anx7625_get_swing_setting(struct device *dev, + struct anx7625_platform_data *pdata) +{ + int num_regs; + + if (of_get_property(dev->of_node, + "analogix,lane0-swing", &num_regs)) { + if (num_regs > DP_TX_SWING_REG_CNT) + num_regs = DP_TX_SWING_REG_CNT; + + pdata->dp_lane0_swing_reg_cnt = num_regs; + of_property_read_u32_array(dev->of_node, "analogix,lane0-swing", + pdata->lane0_reg_data, num_regs); + } + + if (of_get_property(dev->of_node, + "analogix,lane1-swing", &num_regs)) { + if (num_regs > DP_TX_SWING_REG_CNT) + num_regs = DP_TX_SWING_REG_CNT; + + pdata->dp_lane1_swing_reg_cnt = num_regs; + of_property_read_u32_array(dev->of_node, "analogix,lane1-swing", + pdata->lane1_reg_data, num_regs); + } + + return 0; +} + static int anx7625_parse_dt(struct device *dev, struct anx7625_platform_data *pdata) { - struct device_node *np = dev->of_node; + struct device_node *np = dev->of_node, *ep0; struct drm_panel *panel; int ret; + int bus_type, mipi_lanes; + anx7625_get_swing_setting(dev, pdata); + + pdata->is_dpi = 1; /* default dpi mode */ pdata->mipi_host_node = of_graph_get_remote_node(np, 0, 0); if (!pdata->mipi_host_node) { DRM_DEV_ERROR(dev, "fail to get internal panel.\n"); return -ENODEV; } - DRM_DEV_DEBUG_DRIVER(dev, "found dsi host node.\n"); + bus_type = 5; + mipi_lanes = MAX_LANES_SUPPORT; + ep0 = of_graph_get_endpoint_by_regs(np, 0, 0); + if (ep0) { + if (of_property_read_u32(ep0, "bus-type", &bus_type)) + bus_type = 0; + + mipi_lanes = of_property_count_u32_elems(ep0, "data-lanes"); + } + + if (bus_type == 5) /* bus type is Parallel(DSI) */ + pdata->is_dpi = 0; + + pdata->mipi_lanes = mipi_lanes; + if (pdata->mipi_lanes > MAX_LANES_SUPPORT || pdata->mipi_lanes <= 0) + pdata->mipi_lanes = MAX_LANES_SUPPORT; + + if (pdata->is_dpi) + DRM_DEV_DEBUG_DRIVER(dev, "found MIPI DPI host node.\n"); + else + DRM_DEV_DEBUG_DRIVER(dev, "found MIPI DSI host node.\n"); ret = drm_of_find_panel_or_bridge(np, 1, 0, &panel, NULL); if (ret < 0) { @@ -1273,9 +1385,13 @@ static enum drm_connector_status anx7625_sink_detect(struct anx7625_data *ctx) { struct device *dev = &ctx->client->dev; - DRM_DEV_DEBUG_DRIVER(dev, "sink detect, return connected\n"); + DRM_DEV_DEBUG_DRIVER(dev, "sink detect\n"); + + if (ctx->pdata.panel_bridge) + return connector_status_connected; - return connector_status_connected; + return ctx->hpd_status ? connector_status_connected : + connector_status_disconnected; } static int anx7625_attach_dsi(struct anx7625_data *ctx) @@ -1303,7 +1419,7 @@ static int anx7625_attach_dsi(struct anx7625_data *ctx) return -EINVAL; } - dsi->lanes = 4; + dsi->lanes = ctx->pdata.mipi_lanes; dsi->format = MIPI_DSI_FMT_RGB888; dsi->mode_flags = MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_VIDEO_SYNC_PULSE | @@ -1349,10 +1465,12 @@ static int anx7625_bridge_attach(struct drm_bridge *bridge, return -ENODEV; } - err = anx7625_attach_dsi(ctx); - if (err) { - DRM_DEV_ERROR(dev, "Fail to attach to dsi : %d\n", err); - return err; + if (!ctx->pdata.is_dpi) { + err = anx7625_attach_dsi(ctx); + if (err) { + DRM_DEV_ERROR(dev, "Fail to attach to dsi : %d\n", err); + return err; + } } if (ctx->pdata.panel_bridge) { @@ -1451,6 +1569,10 @@ static bool anx7625_bridge_mode_fixup(struct drm_bridge *bridge, DRM_DEV_DEBUG_DRIVER(dev, "drm mode fixup set\n"); + /* No need fixup for external monitor */ + if (!ctx->pdata.panel_bridge) + return true; + hsync = mode->hsync_end - mode->hsync_start; hfp = mode->hsync_start - mode->hdisplay; hbp = mode->htotal - mode->hsync_end; @@ -1827,8 +1949,13 @@ static int anx7625_i2c_probe(struct i2c_client *client, platform->bridge.funcs = &anx7625_bridge_funcs; platform->bridge.of_node = client->dev.of_node; - platform->bridge.ops = DRM_BRIDGE_OP_EDID | DRM_BRIDGE_OP_HPD; - platform->bridge.type = DRM_MODE_CONNECTOR_eDP; + platform->bridge.ops = DRM_BRIDGE_OP_EDID; + if (!platform->pdata.panel_bridge) + platform->bridge.ops |= DRM_BRIDGE_OP_HPD | + DRM_BRIDGE_OP_DETECT; + platform->bridge.type = platform->pdata.panel_bridge ? + DRM_MODE_CONNECTOR_eDP : + DRM_MODE_CONNECTOR_DisplayPort; drm_bridge_add(&platform->bridge); DRM_DEV_DEBUG_DRIVER(dev, "probe done\n"); diff --git a/drivers/gpu/drm/bridge/analogix/anx7625.h b/drivers/gpu/drm/bridge/analogix/anx7625.h index 034c3840028f..65db38e5da9a 100644 --- a/drivers/gpu/drm/bridge/analogix/anx7625.h +++ b/drivers/gpu/drm/bridge/analogix/anx7625.h @@ -141,12 +141,20 @@ #define HORIZONTAL_BACK_PORCH_H 0x22 /* Bit[7:4] are reserved */ /******** END of I2C Address 0x72 *********/ + +/***************************************************************/ +/* Register definition of device address 0x7a */ +#define DP_TX_SWING_REG_CNT 0x14 +#define DP_TX_LANE0_SWING_REG0 0x00 +#define DP_TX_LANE1_SWING_REG0 0x14 +/******** END of I2C Address 0x7a *********/ + /***************************************************************/ /* Register definition of device address 0x7e */ #define I2C_ADDR_7E_FLASH_CONTROLLER 0x7E -#define FLASH_LOAD_STA 0x05 +#define FLASH_LOAD_STA 0x05 #define FLASH_LOAD_STA_CHK BIT(7) #define XTAL_FRQ_SEL 0x3F @@ -347,12 +355,20 @@ struct s_edid_data { /***************** Display End *****************/ +#define MAX_LANES_SUPPORT 4 + struct anx7625_platform_data { struct gpio_desc *gpio_p_on; struct gpio_desc *gpio_reset; struct regulator_bulk_data supplies[3]; struct drm_bridge *panel_bridge; int intp_irq; + int is_dpi; + int mipi_lanes; + int dp_lane0_swing_reg_cnt; + int lane0_reg_data[DP_TX_SWING_REG_CNT]; + int dp_lane1_swing_reg_cnt; + int lane1_reg_data[DP_TX_SWING_REG_CNT]; u32 low_power_mode; struct device_node *mipi_host_node; };