| Message ID | 1721099895-26098-3-git-send-email-hongxing.zhu@nxp.com (mailing list archive) |
|---|---|
| State | Superseded |
| Headers | show |
| Series | Refine i.MX8QM SATA based on generic PHY callbacks | expand |
Hello Richard, On Tue, Jul 16, 2024 at 11:18:13AM +0800, Richard Zhu wrote: > Clean up code by using PHY interface. This commit message needs some improvement. You are removing a bunch of code, but you are not even stating which PHY driver has the equivalent code to the code you are removing. The minimum here is to write the full file path to the PHY driver in the kernel tree that has the equivalent code to the code that you are removing. > > Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com> > --- > drivers/ata/ahci_imx.c | 396 ++++++++++------------------------------- > 1 file changed, 98 insertions(+), 298 deletions(-) > > diff --git a/drivers/ata/ahci_imx.c b/drivers/ata/ahci_imx.c > index cb768f66f0a70..e94c0fdea2260 100644 > --- a/drivers/ata/ahci_imx.c > +++ b/drivers/ata/ahci_imx.c > @@ -19,6 +19,7 @@ > #include <linux/libata.h> > #include <linux/hwmon.h> > #include <linux/hwmon-sysfs.h> > +#include <linux/phy/phy.h> > #include <linux/thermal.h> > #include "ahci.h" > > @@ -44,42 +45,6 @@ enum { > /* Clock Reset Register */ > IMX_CLOCK_RESET = 0x7f3f, > IMX_CLOCK_RESET_RESET = 1 << 0, > - /* IMX8QM HSIO AHCI definitions */ > - IMX8QM_SATA_PHY_RX_IMPED_RATIO_OFFSET = 0x03, > - IMX8QM_SATA_PHY_TX_IMPED_RATIO_OFFSET = 0x09, > - IMX8QM_SATA_PHY_IMPED_RATIO_85OHM = 0x6c, > - IMX8QM_LPCG_PHYX2_OFFSET = 0x00000, > - IMX8QM_CSR_PHYX2_OFFSET = 0x90000, > - IMX8QM_CSR_PHYX1_OFFSET = 0xa0000, > - IMX8QM_CSR_PHYX_STTS0_OFFSET = 0x4, > - IMX8QM_CSR_PCIEA_OFFSET = 0xb0000, > - IMX8QM_CSR_PCIEB_OFFSET = 0xc0000, > - IMX8QM_CSR_SATA_OFFSET = 0xd0000, > - IMX8QM_CSR_PCIE_CTRL2_OFFSET = 0x8, > - IMX8QM_CSR_MISC_OFFSET = 0xe0000, > - > - IMX8QM_LPCG_PHYX2_PCLK0_MASK = (0x3 << 16), > - IMX8QM_LPCG_PHYX2_PCLK1_MASK = (0x3 << 20), > - IMX8QM_PHY_APB_RSTN_0 = BIT(0), > - IMX8QM_PHY_MODE_SATA = BIT(19), > - IMX8QM_PHY_MODE_MASK = (0xf << 17), > - IMX8QM_PHY_PIPE_RSTN_0 = BIT(24), > - IMX8QM_PHY_PIPE_RSTN_OVERRIDE_0 = BIT(25), > - IMX8QM_PHY_PIPE_RSTN_1 = BIT(26), > - IMX8QM_PHY_PIPE_RSTN_OVERRIDE_1 = BIT(27), > - IMX8QM_STTS0_LANE0_TX_PLL_LOCK = BIT(4), > - IMX8QM_MISC_IOB_RXENA = BIT(0), > - IMX8QM_MISC_IOB_TXENA = BIT(1), > - IMX8QM_MISC_PHYX1_EPCS_SEL = BIT(12), > - IMX8QM_MISC_CLKREQN_OUT_OVERRIDE_1 = BIT(24), > - IMX8QM_MISC_CLKREQN_OUT_OVERRIDE_0 = BIT(25), > - IMX8QM_MISC_CLKREQN_IN_OVERRIDE_1 = BIT(28), > - IMX8QM_MISC_CLKREQN_IN_OVERRIDE_0 = BIT(29), > - IMX8QM_SATA_CTRL_RESET_N = BIT(12), > - IMX8QM_SATA_CTRL_EPCS_PHYRESET_N = BIT(7), > - IMX8QM_CTRL_BUTTON_RST_N = BIT(21), > - IMX8QM_CTRL_POWER_UP_RST_N = BIT(23), > - IMX8QM_CTRL_LTSSM_ENABLE = BIT(4), > }; > > enum ahci_imx_type { > @@ -95,14 +60,10 @@ struct imx_ahci_priv { > struct clk *sata_clk; > struct clk *sata_ref_clk; > struct clk *ahb_clk; > - struct clk *epcs_tx_clk; > - struct clk *epcs_rx_clk; > - struct clk *phy_apbclk; > - struct clk *phy_pclk0; > - struct clk *phy_pclk1; > - void __iomem *phy_base; > - struct gpio_desc *clkreq_gpiod; > struct regmap *gpr; > + struct phy *sata_phy; > + struct phy *cali_phy0; > + struct phy *cali_phy1; > bool no_device; > bool first_time; > u32 phy_params; > @@ -450,201 +411,73 @@ ATTRIBUTE_GROUPS(fsl_sata_ahci); > > static int imx8_sata_enable(struct ahci_host_priv *hpriv) > { > - u32 val, reg; > - int i, ret; > + u32 val; > + int ret; > struct imx_ahci_priv *imxpriv = hpriv->plat_data; > struct device *dev = &imxpriv->ahci_pdev->dev; > > - /* configure the hsio for sata */ > - ret = clk_prepare_enable(imxpriv->phy_pclk0); > - if (ret < 0) { > - dev_err(dev, "can't enable phy_pclk0.\n"); > + /* > + * Since "REXT" pin is only present for first lane of i.MX8QM > + * PHY, its calibration results will be stored, passed through > + * to the second lane PHY, and shared with all three lane PHYs. > + * > + * Initialize the first two lane PHYs here, although only the > + * third lane PHY is used by SATA. > + */ > + ret = phy_init(imxpriv->cali_phy0); > + if (ret) { > + dev_err(dev, "cali PHY init failed\n"); > return ret; > } > - ret = clk_prepare_enable(imxpriv->phy_pclk1); > - if (ret < 0) { > - dev_err(dev, "can't enable phy_pclk1.\n"); > - goto disable_phy_pclk0; > + ret = phy_power_on(imxpriv->cali_phy0); > + if (ret) { > + dev_err(dev, "cali PHY power on failed\n"); > + goto err_cali_phy0_exit; > } > - ret = clk_prepare_enable(imxpriv->epcs_tx_clk); > - if (ret < 0) { > - dev_err(dev, "can't enable epcs_tx_clk.\n"); > - goto disable_phy_pclk1; > + ret = phy_init(imxpriv->cali_phy1); > + if (ret) { > + dev_err(dev, "cali PHY1 init failed\n"); > + goto err_cali_phy0_off; > } > - ret = clk_prepare_enable(imxpriv->epcs_rx_clk); > - if (ret < 0) { > - dev_err(dev, "can't enable epcs_rx_clk.\n"); > - goto disable_epcs_tx_clk; > + ret = phy_power_on(imxpriv->cali_phy1); > + if (ret) { > + dev_err(dev, "cali PHY1 power on failed\n"); > + goto err_cali_phy1_exit; > } > - ret = clk_prepare_enable(imxpriv->phy_apbclk); > - if (ret < 0) { > - dev_err(dev, "can't enable phy_apbclk.\n"); > - goto disable_epcs_rx_clk; > + ret = phy_init(imxpriv->sata_phy); > + if (ret) { > + dev_err(dev, "sata PHY init failed\n"); > + goto err_cali_phy1_off; > } > - /* Configure PHYx2 PIPE_RSTN */ > - regmap_read(imxpriv->gpr, IMX8QM_CSR_PCIEA_OFFSET + > - IMX8QM_CSR_PCIE_CTRL2_OFFSET, &val); > - if ((val & IMX8QM_CTRL_LTSSM_ENABLE) == 0) { > - /* The link of the PCIEA of HSIO is down */ > - regmap_update_bits(imxpriv->gpr, > - IMX8QM_CSR_PHYX2_OFFSET, > - IMX8QM_PHY_PIPE_RSTN_0 | > - IMX8QM_PHY_PIPE_RSTN_OVERRIDE_0, > - IMX8QM_PHY_PIPE_RSTN_0 | > - IMX8QM_PHY_PIPE_RSTN_OVERRIDE_0); > + ret = phy_set_mode(imxpriv->sata_phy, PHY_MODE_SATA); > + if (ret) { > + dev_err(dev, "unable to set SATA PHY mode\n"); > + goto err_sata_phy_exit; > } > - regmap_read(imxpriv->gpr, IMX8QM_CSR_PCIEB_OFFSET + > - IMX8QM_CSR_PCIE_CTRL2_OFFSET, ®); > - if ((reg & IMX8QM_CTRL_LTSSM_ENABLE) == 0) { > - /* The link of the PCIEB of HSIO is down */ > - regmap_update_bits(imxpriv->gpr, > - IMX8QM_CSR_PHYX2_OFFSET, > - IMX8QM_PHY_PIPE_RSTN_1 | > - IMX8QM_PHY_PIPE_RSTN_OVERRIDE_1, > - IMX8QM_PHY_PIPE_RSTN_1 | > - IMX8QM_PHY_PIPE_RSTN_OVERRIDE_1); > - } > - if (((reg | val) & IMX8QM_CTRL_LTSSM_ENABLE) == 0) { > - /* The links of both PCIA and PCIEB of HSIO are down */ > - regmap_update_bits(imxpriv->gpr, > - IMX8QM_LPCG_PHYX2_OFFSET, > - IMX8QM_LPCG_PHYX2_PCLK0_MASK | > - IMX8QM_LPCG_PHYX2_PCLK1_MASK, > - 0); > - } > - > - /* set PWR_RST and BT_RST of csr_pciea */ > - val = IMX8QM_CSR_PCIEA_OFFSET + IMX8QM_CSR_PCIE_CTRL2_OFFSET; > - regmap_update_bits(imxpriv->gpr, > - val, > - IMX8QM_CTRL_BUTTON_RST_N, > - IMX8QM_CTRL_BUTTON_RST_N); > - regmap_update_bits(imxpriv->gpr, > - val, > - IMX8QM_CTRL_POWER_UP_RST_N, > - IMX8QM_CTRL_POWER_UP_RST_N); > - > - /* PHYX1_MODE to SATA */ > - regmap_update_bits(imxpriv->gpr, > - IMX8QM_CSR_PHYX1_OFFSET, > - IMX8QM_PHY_MODE_MASK, > - IMX8QM_PHY_MODE_SATA); > - > - /* > - * BIT0 RXENA 1, BIT1 TXENA 0 > - * BIT12 PHY_X1_EPCS_SEL 1. > - */ > - regmap_update_bits(imxpriv->gpr, > - IMX8QM_CSR_MISC_OFFSET, > - IMX8QM_MISC_IOB_RXENA, > - IMX8QM_MISC_IOB_RXENA); > - regmap_update_bits(imxpriv->gpr, > - IMX8QM_CSR_MISC_OFFSET, > - IMX8QM_MISC_IOB_TXENA, > - 0); > - regmap_update_bits(imxpriv->gpr, > - IMX8QM_CSR_MISC_OFFSET, > - IMX8QM_MISC_PHYX1_EPCS_SEL, > - IMX8QM_MISC_PHYX1_EPCS_SEL); > - /* > - * It is possible, for PCIe and SATA are sharing > - * the same clock source, HPLL or external oscillator. > - * When PCIe is in low power modes (L1.X or L2 etc), > - * the clock source can be turned off. In this case, > - * if this clock source is required to be toggling by > - * SATA, then SATA functions will be abnormal. > - * Set the override here to avoid it. > - */ > - regmap_update_bits(imxpriv->gpr, > - IMX8QM_CSR_MISC_OFFSET, > - IMX8QM_MISC_CLKREQN_OUT_OVERRIDE_1 | > - IMX8QM_MISC_CLKREQN_OUT_OVERRIDE_0 | > - IMX8QM_MISC_CLKREQN_IN_OVERRIDE_1 | > - IMX8QM_MISC_CLKREQN_IN_OVERRIDE_0, > - IMX8QM_MISC_CLKREQN_OUT_OVERRIDE_1 | > - IMX8QM_MISC_CLKREQN_OUT_OVERRIDE_0 | > - IMX8QM_MISC_CLKREQN_IN_OVERRIDE_1 | > - IMX8QM_MISC_CLKREQN_IN_OVERRIDE_0); > - > - /* clear PHY RST, then set it */ > - regmap_update_bits(imxpriv->gpr, > - IMX8QM_CSR_SATA_OFFSET, > - IMX8QM_SATA_CTRL_EPCS_PHYRESET_N, > - 0); > - > - regmap_update_bits(imxpriv->gpr, > - IMX8QM_CSR_SATA_OFFSET, > - IMX8QM_SATA_CTRL_EPCS_PHYRESET_N, > - IMX8QM_SATA_CTRL_EPCS_PHYRESET_N); > - > - /* CTRL RST: SET -> delay 1 us -> CLEAR -> SET */ > - regmap_update_bits(imxpriv->gpr, > - IMX8QM_CSR_SATA_OFFSET, > - IMX8QM_SATA_CTRL_RESET_N, > - IMX8QM_SATA_CTRL_RESET_N); > - udelay(1); > - regmap_update_bits(imxpriv->gpr, > - IMX8QM_CSR_SATA_OFFSET, > - IMX8QM_SATA_CTRL_RESET_N, > - 0); > - regmap_update_bits(imxpriv->gpr, > - IMX8QM_CSR_SATA_OFFSET, > - IMX8QM_SATA_CTRL_RESET_N, > - IMX8QM_SATA_CTRL_RESET_N); > - > - /* APB reset */ > - regmap_update_bits(imxpriv->gpr, > - IMX8QM_CSR_PHYX1_OFFSET, > - IMX8QM_PHY_APB_RSTN_0, > - IMX8QM_PHY_APB_RSTN_0); > - > - for (i = 0; i < 100; i++) { > - reg = IMX8QM_CSR_PHYX1_OFFSET + > - IMX8QM_CSR_PHYX_STTS0_OFFSET; > - regmap_read(imxpriv->gpr, reg, &val); > - val &= IMX8QM_STTS0_LANE0_TX_PLL_LOCK; > - if (val == IMX8QM_STTS0_LANE0_TX_PLL_LOCK) > - break; > - udelay(1); > + ret = phy_power_on(imxpriv->sata_phy); > + if (ret) { > + dev_err(dev, "sata PHY power up failed\n"); > + goto err_sata_phy_exit; > } > > - if (val != IMX8QM_STTS0_LANE0_TX_PLL_LOCK) { > - dev_err(dev, "TX PLL of the PHY is not locked\n"); > - ret = -ENODEV; > - } else { > - writeb(imxpriv->imped_ratio, imxpriv->phy_base + > - IMX8QM_SATA_PHY_RX_IMPED_RATIO_OFFSET); > - writeb(imxpriv->imped_ratio, imxpriv->phy_base + > - IMX8QM_SATA_PHY_TX_IMPED_RATIO_OFFSET); > - reg = readb(imxpriv->phy_base + > - IMX8QM_SATA_PHY_RX_IMPED_RATIO_OFFSET); > - if (unlikely(reg != imxpriv->imped_ratio)) > - dev_info(dev, "Can't set PHY RX impedance ratio.\n"); > - reg = readb(imxpriv->phy_base + > - IMX8QM_SATA_PHY_TX_IMPED_RATIO_OFFSET); > - if (unlikely(reg != imxpriv->imped_ratio)) > - dev_info(dev, "Can't set PHY TX impedance ratio.\n"); > - usleep_range(50, 100); > + /* The cali_phy# can be turned off after SATA PHY is initialized. */ > + phy_power_off(imxpriv->cali_phy1); > + phy_exit(imxpriv->cali_phy1); > + phy_power_off(imxpriv->cali_phy0); > + phy_exit(imxpriv->cali_phy0); > > - /* > - * To reduce the power consumption, gate off > - * the PHY clks > - */ > - clk_disable_unprepare(imxpriv->phy_apbclk); > - clk_disable_unprepare(imxpriv->phy_pclk1); > - clk_disable_unprepare(imxpriv->phy_pclk0); > - return ret; > - } > + return 0; > > - clk_disable_unprepare(imxpriv->phy_apbclk); > -disable_epcs_rx_clk: > - clk_disable_unprepare(imxpriv->epcs_rx_clk); > -disable_epcs_tx_clk: > - clk_disable_unprepare(imxpriv->epcs_tx_clk); > -disable_phy_pclk1: > - clk_disable_unprepare(imxpriv->phy_pclk1); > -disable_phy_pclk0: > - clk_disable_unprepare(imxpriv->phy_pclk0); > +err_sata_phy_exit: > + phy_exit(imxpriv->sata_phy); > +err_cali_phy1_off: > + phy_power_off(imxpriv->cali_phy1); > +err_cali_phy1_exit: > + phy_exit(imxpriv->cali_phy1); > +err_cali_phy0_off: > + phy_power_off(imxpriv->cali_phy0); > +err_cali_phy0_exit: > + phy_exit(imxpriv->cali_phy0); > > return ret; > } > @@ -698,6 +531,9 @@ static int imx_sata_enable(struct ahci_host_priv *hpriv) > } > } else if (imxpriv->type == AHCI_IMX8QM) { > ret = imx8_sata_enable(hpriv); > + if (ret) > + goto disable_clk; > + > } > > usleep_range(1000, 2000); > @@ -736,8 +572,10 @@ static void imx_sata_disable(struct ahci_host_priv *hpriv) > break; > > case AHCI_IMX8QM: > - clk_disable_unprepare(imxpriv->epcs_rx_clk); > - clk_disable_unprepare(imxpriv->epcs_tx_clk); > + if (imxpriv->sata_phy) { > + phy_power_off(imxpriv->sata_phy); > + phy_exit(imxpriv->sata_phy); > + } > break; > > default: > @@ -760,6 +598,9 @@ static void ahci_imx_error_handler(struct ata_port *ap) > > ahci_error_handler(ap); > > + if (imxpriv->type == AHCI_IMX8QM) > + return; > + > if (!(imxpriv->first_time) || ahci_imx_hotplug) > return; > > @@ -986,65 +827,22 @@ static const struct scsi_host_template ahci_platform_sht = { > > static int imx8_sata_probe(struct device *dev, struct imx_ahci_priv *imxpriv) > { > - struct resource *phy_res; > - struct platform_device *pdev = imxpriv->ahci_pdev; > - struct device_node *np = dev->of_node; > - > - if (of_property_read_u32(np, "fsl,phy-imp", &imxpriv->imped_ratio)) > - imxpriv->imped_ratio = IMX8QM_SATA_PHY_IMPED_RATIO_85OHM; > - phy_res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "phy"); > - if (phy_res) { > - imxpriv->phy_base = devm_ioremap(dev, phy_res->start, > - resource_size(phy_res)); > - if (!imxpriv->phy_base) { > - dev_err(dev, "error with ioremap\n"); > - return -ENOMEM; > - } > - } else { > - dev_err(dev, "missing *phy* reg region.\n"); > - return -ENOMEM; > - } > - imxpriv->gpr = > - syscon_regmap_lookup_by_phandle(np, "hsio"); > - if (IS_ERR(imxpriv->gpr)) { > - dev_err(dev, "unable to find gpr registers\n"); > - return PTR_ERR(imxpriv->gpr); > - } > - > - imxpriv->epcs_tx_clk = devm_clk_get(dev, "epcs_tx"); > - if (IS_ERR(imxpriv->epcs_tx_clk)) { > - dev_err(dev, "can't get epcs_tx_clk clock.\n"); > - return PTR_ERR(imxpriv->epcs_tx_clk); > - } > - imxpriv->epcs_rx_clk = devm_clk_get(dev, "epcs_rx"); > - if (IS_ERR(imxpriv->epcs_rx_clk)) { > - dev_err(dev, "can't get epcs_rx_clk clock.\n"); > - return PTR_ERR(imxpriv->epcs_rx_clk); > - } > - imxpriv->phy_pclk0 = devm_clk_get(dev, "phy_pclk0"); > - if (IS_ERR(imxpriv->phy_pclk0)) { > - dev_err(dev, "can't get phy_pclk0 clock.\n"); > - return PTR_ERR(imxpriv->phy_pclk0); > - } > - imxpriv->phy_pclk1 = devm_clk_get(dev, "phy_pclk1"); > - if (IS_ERR(imxpriv->phy_pclk1)) { > - dev_err(dev, "can't get phy_pclk1 clock.\n"); > - return PTR_ERR(imxpriv->phy_pclk1); > - } > - imxpriv->phy_apbclk = devm_clk_get(dev, "phy_apbclk"); > - if (IS_ERR(imxpriv->phy_apbclk)) { > - dev_err(dev, "can't get phy_apbclk clock.\n"); > - return PTR_ERR(imxpriv->phy_apbclk); > - } > - > - /* Fetch GPIO, then enable the external OSC */ > - imxpriv->clkreq_gpiod = devm_gpiod_get_optional(dev, "clkreq", > - GPIOD_OUT_LOW | GPIOD_FLAGS_BIT_NONEXCLUSIVE); > - if (IS_ERR(imxpriv->clkreq_gpiod)) > - return PTR_ERR(imxpriv->clkreq_gpiod); > - if (imxpriv->clkreq_gpiod) > - gpiod_set_consumer_name(imxpriv->clkreq_gpiod, "SATA CLKREQ"); > - > + if (!(dev->bus_dma_limit)) > + dev->bus_dma_limit = DMA_BIT_MASK(32); > + > + imxpriv->sata_phy = devm_phy_get(dev, "sata-phy"); > + if (IS_ERR(imxpriv->sata_phy)) > + return dev_err_probe(dev, PTR_ERR(imxpriv->sata_phy), > + "Failed to get sata_phy\n"); > + > + imxpriv->cali_phy0 = devm_phy_get(dev, "cali-phy0"); > + if (IS_ERR(imxpriv->cali_phy0)) > + return dev_err_probe(dev, PTR_ERR(imxpriv->cali_phy0), > + "Failed to get cali_phy0\n"); > + imxpriv->cali_phy1 = devm_phy_get(dev, "cali-phy1"); > + if (IS_ERR(imxpriv->cali_phy1)) > + return dev_err_probe(dev, PTR_ERR(imxpriv->cali_phy1), > + "Failed to get cali_phy1\n"); > return 0; > } > > @@ -1077,12 +875,6 @@ static int imx_ahci_probe(struct platform_device *pdev) > return PTR_ERR(imxpriv->sata_ref_clk); > } > > - imxpriv->ahb_clk = devm_clk_get(dev, "ahb"); > - if (IS_ERR(imxpriv->ahb_clk)) { > - dev_err(dev, "can't get ahb clock.\n"); > - return PTR_ERR(imxpriv->ahb_clk); > - } > - > if (imxpriv->type == AHCI_IMX6Q || imxpriv->type == AHCI_IMX6QP) { > u32 reg_value; > > @@ -1142,11 +934,8 @@ static int imx_ahci_probe(struct platform_device *pdev) > goto disable_clk; > > /* > - * Configure the HWINIT bits of the HOST_CAP and HOST_PORTS_IMPL, > - * and IP vendor specific register IMX_TIMER1MS. > - * Configure CAP_SSS (support stagered spin up). > - * Implement the port0. > - * Get the ahb clock rate, and configure the TIMER1MS register. > + * Configure the HWINIT bits of the HOST_CAP and HOST_PORTS_IMPL. > + * Set CAP_SSS (support stagered spin up) and Implement the port0. > */ > reg_val = readl(hpriv->mmio + HOST_CAP); > if (!(reg_val & HOST_CAP_SSS)) { > @@ -1159,8 +948,19 @@ static int imx_ahci_probe(struct platform_device *pdev) > writel(reg_val, hpriv->mmio + HOST_PORTS_IMPL); > } > > - reg_val = clk_get_rate(imxpriv->ahb_clk) / 1000; > - writel(reg_val, hpriv->mmio + IMX_TIMER1MS); > + if (imxpriv->type != AHCI_IMX8QM) { > + /* > + * Get AHB clock rate and configure the vendor specified > + * TIMER1MS register on i.MX53, i.MX6Q and i.MX6QP only. > + */ > + imxpriv->ahb_clk = devm_clk_get(dev, "ahb"); > + if (IS_ERR(imxpriv->ahb_clk)) { > + dev_err(dev, "Failed to get ahb clock\n"); > + goto disable_sata; > + } > + reg_val = clk_get_rate(imxpriv->ahb_clk) / 1000; > + writel(reg_val, hpriv->mmio + IMX_TIMER1MS); > + } This chunk has nothing to do with: "ata: ahci_imx: Clean up code by using i.MX8Q HSIO PHY driver" so it should be in a separate commit, with a proper commit message. Kind regards, Niklas
On Tue, Jul 16, 2024 at 11:18:13AM +0800, Richard Zhu wrote: > Clean up code by using PHY interface. > > Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com> > --- > drivers/ata/ahci_imx.c | 396 ++++++++++------------------------------- > 1 file changed, 98 insertions(+), 298 deletions(-) > > diff --git a/drivers/ata/ahci_imx.c b/drivers/ata/ahci_imx.c > index cb768f66f0a70..e94c0fdea2260 100644 > --- a/drivers/ata/ahci_imx.c > +++ b/drivers/ata/ahci_imx.c > @@ -986,65 +827,22 @@ static const struct scsi_host_template ahci_platform_sht = { > > static int imx8_sata_probe(struct device *dev, struct imx_ahci_priv *imxpriv) > { > - struct resource *phy_res; > - struct platform_device *pdev = imxpriv->ahci_pdev; > - struct device_node *np = dev->of_node; > - > - if (of_property_read_u32(np, "fsl,phy-imp", &imxpriv->imped_ratio)) > - imxpriv->imped_ratio = IMX8QM_SATA_PHY_IMPED_RATIO_85OHM; > - phy_res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "phy"); > - if (phy_res) { > - imxpriv->phy_base = devm_ioremap(dev, phy_res->start, > - resource_size(phy_res)); > - if (!imxpriv->phy_base) { > - dev_err(dev, "error with ioremap\n"); > - return -ENOMEM; > - } > - } else { > - dev_err(dev, "missing *phy* reg region.\n"); > - return -ENOMEM; > - } > - imxpriv->gpr = > - syscon_regmap_lookup_by_phandle(np, "hsio"); > - if (IS_ERR(imxpriv->gpr)) { > - dev_err(dev, "unable to find gpr registers\n"); > - return PTR_ERR(imxpriv->gpr); > - } > - > - imxpriv->epcs_tx_clk = devm_clk_get(dev, "epcs_tx"); > - if (IS_ERR(imxpriv->epcs_tx_clk)) { > - dev_err(dev, "can't get epcs_tx_clk clock.\n"); > - return PTR_ERR(imxpriv->epcs_tx_clk); > - } > - imxpriv->epcs_rx_clk = devm_clk_get(dev, "epcs_rx"); > - if (IS_ERR(imxpriv->epcs_rx_clk)) { > - dev_err(dev, "can't get epcs_rx_clk clock.\n"); > - return PTR_ERR(imxpriv->epcs_rx_clk); > - } > - imxpriv->phy_pclk0 = devm_clk_get(dev, "phy_pclk0"); > - if (IS_ERR(imxpriv->phy_pclk0)) { > - dev_err(dev, "can't get phy_pclk0 clock.\n"); > - return PTR_ERR(imxpriv->phy_pclk0); > - } > - imxpriv->phy_pclk1 = devm_clk_get(dev, "phy_pclk1"); > - if (IS_ERR(imxpriv->phy_pclk1)) { > - dev_err(dev, "can't get phy_pclk1 clock.\n"); > - return PTR_ERR(imxpriv->phy_pclk1); > - } > - imxpriv->phy_apbclk = devm_clk_get(dev, "phy_apbclk"); > - if (IS_ERR(imxpriv->phy_apbclk)) { > - dev_err(dev, "can't get phy_apbclk clock.\n"); > - return PTR_ERR(imxpriv->phy_apbclk); > - } > - > - /* Fetch GPIO, then enable the external OSC */ > - imxpriv->clkreq_gpiod = devm_gpiod_get_optional(dev, "clkreq", > - GPIOD_OUT_LOW | GPIOD_FLAGS_BIT_NONEXCLUSIVE); > - if (IS_ERR(imxpriv->clkreq_gpiod)) > - return PTR_ERR(imxpriv->clkreq_gpiod); > - if (imxpriv->clkreq_gpiod) > - gpiod_set_consumer_name(imxpriv->clkreq_gpiod, "SATA CLKREQ"); > - > + if (!(dev->bus_dma_limit)) > + dev->bus_dma_limit = DMA_BIT_MASK(32); These two lines look like a unrelated change, should be in a separate commit with a proper commit message. Kind regards, Niklas
diff --git a/drivers/ata/ahci_imx.c b/drivers/ata/ahci_imx.c index cb768f66f0a70..e94c0fdea2260 100644 --- a/drivers/ata/ahci_imx.c +++ b/drivers/ata/ahci_imx.c @@ -19,6 +19,7 @@ #include <linux/libata.h> #include <linux/hwmon.h> #include <linux/hwmon-sysfs.h> +#include <linux/phy/phy.h> #include <linux/thermal.h> #include "ahci.h" @@ -44,42 +45,6 @@ enum { /* Clock Reset Register */ IMX_CLOCK_RESET = 0x7f3f, IMX_CLOCK_RESET_RESET = 1 << 0, - /* IMX8QM HSIO AHCI definitions */ - IMX8QM_SATA_PHY_RX_IMPED_RATIO_OFFSET = 0x03, - IMX8QM_SATA_PHY_TX_IMPED_RATIO_OFFSET = 0x09, - IMX8QM_SATA_PHY_IMPED_RATIO_85OHM = 0x6c, - IMX8QM_LPCG_PHYX2_OFFSET = 0x00000, - IMX8QM_CSR_PHYX2_OFFSET = 0x90000, - IMX8QM_CSR_PHYX1_OFFSET = 0xa0000, - IMX8QM_CSR_PHYX_STTS0_OFFSET = 0x4, - IMX8QM_CSR_PCIEA_OFFSET = 0xb0000, - IMX8QM_CSR_PCIEB_OFFSET = 0xc0000, - IMX8QM_CSR_SATA_OFFSET = 0xd0000, - IMX8QM_CSR_PCIE_CTRL2_OFFSET = 0x8, - IMX8QM_CSR_MISC_OFFSET = 0xe0000, - - IMX8QM_LPCG_PHYX2_PCLK0_MASK = (0x3 << 16), - IMX8QM_LPCG_PHYX2_PCLK1_MASK = (0x3 << 20), - IMX8QM_PHY_APB_RSTN_0 = BIT(0), - IMX8QM_PHY_MODE_SATA = BIT(19), - IMX8QM_PHY_MODE_MASK = (0xf << 17), - IMX8QM_PHY_PIPE_RSTN_0 = BIT(24), - IMX8QM_PHY_PIPE_RSTN_OVERRIDE_0 = BIT(25), - IMX8QM_PHY_PIPE_RSTN_1 = BIT(26), - IMX8QM_PHY_PIPE_RSTN_OVERRIDE_1 = BIT(27), - IMX8QM_STTS0_LANE0_TX_PLL_LOCK = BIT(4), - IMX8QM_MISC_IOB_RXENA = BIT(0), - IMX8QM_MISC_IOB_TXENA = BIT(1), - IMX8QM_MISC_PHYX1_EPCS_SEL = BIT(12), - IMX8QM_MISC_CLKREQN_OUT_OVERRIDE_1 = BIT(24), - IMX8QM_MISC_CLKREQN_OUT_OVERRIDE_0 = BIT(25), - IMX8QM_MISC_CLKREQN_IN_OVERRIDE_1 = BIT(28), - IMX8QM_MISC_CLKREQN_IN_OVERRIDE_0 = BIT(29), - IMX8QM_SATA_CTRL_RESET_N = BIT(12), - IMX8QM_SATA_CTRL_EPCS_PHYRESET_N = BIT(7), - IMX8QM_CTRL_BUTTON_RST_N = BIT(21), - IMX8QM_CTRL_POWER_UP_RST_N = BIT(23), - IMX8QM_CTRL_LTSSM_ENABLE = BIT(4), }; enum ahci_imx_type { @@ -95,14 +60,10 @@ struct imx_ahci_priv { struct clk *sata_clk; struct clk *sata_ref_clk; struct clk *ahb_clk; - struct clk *epcs_tx_clk; - struct clk *epcs_rx_clk; - struct clk *phy_apbclk; - struct clk *phy_pclk0; - struct clk *phy_pclk1; - void __iomem *phy_base; - struct gpio_desc *clkreq_gpiod; struct regmap *gpr; + struct phy *sata_phy; + struct phy *cali_phy0; + struct phy *cali_phy1; bool no_device; bool first_time; u32 phy_params; @@ -450,201 +411,73 @@ ATTRIBUTE_GROUPS(fsl_sata_ahci); static int imx8_sata_enable(struct ahci_host_priv *hpriv) { - u32 val, reg; - int i, ret; + u32 val; + int ret; struct imx_ahci_priv *imxpriv = hpriv->plat_data; struct device *dev = &imxpriv->ahci_pdev->dev; - /* configure the hsio for sata */ - ret = clk_prepare_enable(imxpriv->phy_pclk0); - if (ret < 0) { - dev_err(dev, "can't enable phy_pclk0.\n"); + /* + * Since "REXT" pin is only present for first lane of i.MX8QM + * PHY, its calibration results will be stored, passed through + * to the second lane PHY, and shared with all three lane PHYs. + * + * Initialize the first two lane PHYs here, although only the + * third lane PHY is used by SATA. + */ + ret = phy_init(imxpriv->cali_phy0); + if (ret) { + dev_err(dev, "cali PHY init failed\n"); return ret; } - ret = clk_prepare_enable(imxpriv->phy_pclk1); - if (ret < 0) { - dev_err(dev, "can't enable phy_pclk1.\n"); - goto disable_phy_pclk0; + ret = phy_power_on(imxpriv->cali_phy0); + if (ret) { + dev_err(dev, "cali PHY power on failed\n"); + goto err_cali_phy0_exit; } - ret = clk_prepare_enable(imxpriv->epcs_tx_clk); - if (ret < 0) { - dev_err(dev, "can't enable epcs_tx_clk.\n"); - goto disable_phy_pclk1; + ret = phy_init(imxpriv->cali_phy1); + if (ret) { + dev_err(dev, "cali PHY1 init failed\n"); + goto err_cali_phy0_off; } - ret = clk_prepare_enable(imxpriv->epcs_rx_clk); - if (ret < 0) { - dev_err(dev, "can't enable epcs_rx_clk.\n"); - goto disable_epcs_tx_clk; + ret = phy_power_on(imxpriv->cali_phy1); + if (ret) { + dev_err(dev, "cali PHY1 power on failed\n"); + goto err_cali_phy1_exit; } - ret = clk_prepare_enable(imxpriv->phy_apbclk); - if (ret < 0) { - dev_err(dev, "can't enable phy_apbclk.\n"); - goto disable_epcs_rx_clk; + ret = phy_init(imxpriv->sata_phy); + if (ret) { + dev_err(dev, "sata PHY init failed\n"); + goto err_cali_phy1_off; } - /* Configure PHYx2 PIPE_RSTN */ - regmap_read(imxpriv->gpr, IMX8QM_CSR_PCIEA_OFFSET + - IMX8QM_CSR_PCIE_CTRL2_OFFSET, &val); - if ((val & IMX8QM_CTRL_LTSSM_ENABLE) == 0) { - /* The link of the PCIEA of HSIO is down */ - regmap_update_bits(imxpriv->gpr, - IMX8QM_CSR_PHYX2_OFFSET, - IMX8QM_PHY_PIPE_RSTN_0 | - IMX8QM_PHY_PIPE_RSTN_OVERRIDE_0, - IMX8QM_PHY_PIPE_RSTN_0 | - IMX8QM_PHY_PIPE_RSTN_OVERRIDE_0); + ret = phy_set_mode(imxpriv->sata_phy, PHY_MODE_SATA); + if (ret) { + dev_err(dev, "unable to set SATA PHY mode\n"); + goto err_sata_phy_exit; } - regmap_read(imxpriv->gpr, IMX8QM_CSR_PCIEB_OFFSET + - IMX8QM_CSR_PCIE_CTRL2_OFFSET, ®); - if ((reg & IMX8QM_CTRL_LTSSM_ENABLE) == 0) { - /* The link of the PCIEB of HSIO is down */ - regmap_update_bits(imxpriv->gpr, - IMX8QM_CSR_PHYX2_OFFSET, - IMX8QM_PHY_PIPE_RSTN_1 | - IMX8QM_PHY_PIPE_RSTN_OVERRIDE_1, - IMX8QM_PHY_PIPE_RSTN_1 | - IMX8QM_PHY_PIPE_RSTN_OVERRIDE_1); - } - if (((reg | val) & IMX8QM_CTRL_LTSSM_ENABLE) == 0) { - /* The links of both PCIA and PCIEB of HSIO are down */ - regmap_update_bits(imxpriv->gpr, - IMX8QM_LPCG_PHYX2_OFFSET, - IMX8QM_LPCG_PHYX2_PCLK0_MASK | - IMX8QM_LPCG_PHYX2_PCLK1_MASK, - 0); - } - - /* set PWR_RST and BT_RST of csr_pciea */ - val = IMX8QM_CSR_PCIEA_OFFSET + IMX8QM_CSR_PCIE_CTRL2_OFFSET; - regmap_update_bits(imxpriv->gpr, - val, - IMX8QM_CTRL_BUTTON_RST_N, - IMX8QM_CTRL_BUTTON_RST_N); - regmap_update_bits(imxpriv->gpr, - val, - IMX8QM_CTRL_POWER_UP_RST_N, - IMX8QM_CTRL_POWER_UP_RST_N); - - /* PHYX1_MODE to SATA */ - regmap_update_bits(imxpriv->gpr, - IMX8QM_CSR_PHYX1_OFFSET, - IMX8QM_PHY_MODE_MASK, - IMX8QM_PHY_MODE_SATA); - - /* - * BIT0 RXENA 1, BIT1 TXENA 0 - * BIT12 PHY_X1_EPCS_SEL 1. - */ - regmap_update_bits(imxpriv->gpr, - IMX8QM_CSR_MISC_OFFSET, - IMX8QM_MISC_IOB_RXENA, - IMX8QM_MISC_IOB_RXENA); - regmap_update_bits(imxpriv->gpr, - IMX8QM_CSR_MISC_OFFSET, - IMX8QM_MISC_IOB_TXENA, - 0); - regmap_update_bits(imxpriv->gpr, - IMX8QM_CSR_MISC_OFFSET, - IMX8QM_MISC_PHYX1_EPCS_SEL, - IMX8QM_MISC_PHYX1_EPCS_SEL); - /* - * It is possible, for PCIe and SATA are sharing - * the same clock source, HPLL or external oscillator. - * When PCIe is in low power modes (L1.X or L2 etc), - * the clock source can be turned off. In this case, - * if this clock source is required to be toggling by - * SATA, then SATA functions will be abnormal. - * Set the override here to avoid it. - */ - regmap_update_bits(imxpriv->gpr, - IMX8QM_CSR_MISC_OFFSET, - IMX8QM_MISC_CLKREQN_OUT_OVERRIDE_1 | - IMX8QM_MISC_CLKREQN_OUT_OVERRIDE_0 | - IMX8QM_MISC_CLKREQN_IN_OVERRIDE_1 | - IMX8QM_MISC_CLKREQN_IN_OVERRIDE_0, - IMX8QM_MISC_CLKREQN_OUT_OVERRIDE_1 | - IMX8QM_MISC_CLKREQN_OUT_OVERRIDE_0 | - IMX8QM_MISC_CLKREQN_IN_OVERRIDE_1 | - IMX8QM_MISC_CLKREQN_IN_OVERRIDE_0); - - /* clear PHY RST, then set it */ - regmap_update_bits(imxpriv->gpr, - IMX8QM_CSR_SATA_OFFSET, - IMX8QM_SATA_CTRL_EPCS_PHYRESET_N, - 0); - - regmap_update_bits(imxpriv->gpr, - IMX8QM_CSR_SATA_OFFSET, - IMX8QM_SATA_CTRL_EPCS_PHYRESET_N, - IMX8QM_SATA_CTRL_EPCS_PHYRESET_N); - - /* CTRL RST: SET -> delay 1 us -> CLEAR -> SET */ - regmap_update_bits(imxpriv->gpr, - IMX8QM_CSR_SATA_OFFSET, - IMX8QM_SATA_CTRL_RESET_N, - IMX8QM_SATA_CTRL_RESET_N); - udelay(1); - regmap_update_bits(imxpriv->gpr, - IMX8QM_CSR_SATA_OFFSET, - IMX8QM_SATA_CTRL_RESET_N, - 0); - regmap_update_bits(imxpriv->gpr, - IMX8QM_CSR_SATA_OFFSET, - IMX8QM_SATA_CTRL_RESET_N, - IMX8QM_SATA_CTRL_RESET_N); - - /* APB reset */ - regmap_update_bits(imxpriv->gpr, - IMX8QM_CSR_PHYX1_OFFSET, - IMX8QM_PHY_APB_RSTN_0, - IMX8QM_PHY_APB_RSTN_0); - - for (i = 0; i < 100; i++) { - reg = IMX8QM_CSR_PHYX1_OFFSET + - IMX8QM_CSR_PHYX_STTS0_OFFSET; - regmap_read(imxpriv->gpr, reg, &val); - val &= IMX8QM_STTS0_LANE0_TX_PLL_LOCK; - if (val == IMX8QM_STTS0_LANE0_TX_PLL_LOCK) - break; - udelay(1); + ret = phy_power_on(imxpriv->sata_phy); + if (ret) { + dev_err(dev, "sata PHY power up failed\n"); + goto err_sata_phy_exit; } - if (val != IMX8QM_STTS0_LANE0_TX_PLL_LOCK) { - dev_err(dev, "TX PLL of the PHY is not locked\n"); - ret = -ENODEV; - } else { - writeb(imxpriv->imped_ratio, imxpriv->phy_base + - IMX8QM_SATA_PHY_RX_IMPED_RATIO_OFFSET); - writeb(imxpriv->imped_ratio, imxpriv->phy_base + - IMX8QM_SATA_PHY_TX_IMPED_RATIO_OFFSET); - reg = readb(imxpriv->phy_base + - IMX8QM_SATA_PHY_RX_IMPED_RATIO_OFFSET); - if (unlikely(reg != imxpriv->imped_ratio)) - dev_info(dev, "Can't set PHY RX impedance ratio.\n"); - reg = readb(imxpriv->phy_base + - IMX8QM_SATA_PHY_TX_IMPED_RATIO_OFFSET); - if (unlikely(reg != imxpriv->imped_ratio)) - dev_info(dev, "Can't set PHY TX impedance ratio.\n"); - usleep_range(50, 100); + /* The cali_phy# can be turned off after SATA PHY is initialized. */ + phy_power_off(imxpriv->cali_phy1); + phy_exit(imxpriv->cali_phy1); + phy_power_off(imxpriv->cali_phy0); + phy_exit(imxpriv->cali_phy0); - /* - * To reduce the power consumption, gate off - * the PHY clks - */ - clk_disable_unprepare(imxpriv->phy_apbclk); - clk_disable_unprepare(imxpriv->phy_pclk1); - clk_disable_unprepare(imxpriv->phy_pclk0); - return ret; - } + return 0; - clk_disable_unprepare(imxpriv->phy_apbclk); -disable_epcs_rx_clk: - clk_disable_unprepare(imxpriv->epcs_rx_clk); -disable_epcs_tx_clk: - clk_disable_unprepare(imxpriv->epcs_tx_clk); -disable_phy_pclk1: - clk_disable_unprepare(imxpriv->phy_pclk1); -disable_phy_pclk0: - clk_disable_unprepare(imxpriv->phy_pclk0); +err_sata_phy_exit: + phy_exit(imxpriv->sata_phy); +err_cali_phy1_off: + phy_power_off(imxpriv->cali_phy1); +err_cali_phy1_exit: + phy_exit(imxpriv->cali_phy1); +err_cali_phy0_off: + phy_power_off(imxpriv->cali_phy0); +err_cali_phy0_exit: + phy_exit(imxpriv->cali_phy0); return ret; } @@ -698,6 +531,9 @@ static int imx_sata_enable(struct ahci_host_priv *hpriv) } } else if (imxpriv->type == AHCI_IMX8QM) { ret = imx8_sata_enable(hpriv); + if (ret) + goto disable_clk; + } usleep_range(1000, 2000); @@ -736,8 +572,10 @@ static void imx_sata_disable(struct ahci_host_priv *hpriv) break; case AHCI_IMX8QM: - clk_disable_unprepare(imxpriv->epcs_rx_clk); - clk_disable_unprepare(imxpriv->epcs_tx_clk); + if (imxpriv->sata_phy) { + phy_power_off(imxpriv->sata_phy); + phy_exit(imxpriv->sata_phy); + } break; default: @@ -760,6 +598,9 @@ static void ahci_imx_error_handler(struct ata_port *ap) ahci_error_handler(ap); + if (imxpriv->type == AHCI_IMX8QM) + return; + if (!(imxpriv->first_time) || ahci_imx_hotplug) return; @@ -986,65 +827,22 @@ static const struct scsi_host_template ahci_platform_sht = { static int imx8_sata_probe(struct device *dev, struct imx_ahci_priv *imxpriv) { - struct resource *phy_res; - struct platform_device *pdev = imxpriv->ahci_pdev; - struct device_node *np = dev->of_node; - - if (of_property_read_u32(np, "fsl,phy-imp", &imxpriv->imped_ratio)) - imxpriv->imped_ratio = IMX8QM_SATA_PHY_IMPED_RATIO_85OHM; - phy_res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "phy"); - if (phy_res) { - imxpriv->phy_base = devm_ioremap(dev, phy_res->start, - resource_size(phy_res)); - if (!imxpriv->phy_base) { - dev_err(dev, "error with ioremap\n"); - return -ENOMEM; - } - } else { - dev_err(dev, "missing *phy* reg region.\n"); - return -ENOMEM; - } - imxpriv->gpr = - syscon_regmap_lookup_by_phandle(np, "hsio"); - if (IS_ERR(imxpriv->gpr)) { - dev_err(dev, "unable to find gpr registers\n"); - return PTR_ERR(imxpriv->gpr); - } - - imxpriv->epcs_tx_clk = devm_clk_get(dev, "epcs_tx"); - if (IS_ERR(imxpriv->epcs_tx_clk)) { - dev_err(dev, "can't get epcs_tx_clk clock.\n"); - return PTR_ERR(imxpriv->epcs_tx_clk); - } - imxpriv->epcs_rx_clk = devm_clk_get(dev, "epcs_rx"); - if (IS_ERR(imxpriv->epcs_rx_clk)) { - dev_err(dev, "can't get epcs_rx_clk clock.\n"); - return PTR_ERR(imxpriv->epcs_rx_clk); - } - imxpriv->phy_pclk0 = devm_clk_get(dev, "phy_pclk0"); - if (IS_ERR(imxpriv->phy_pclk0)) { - dev_err(dev, "can't get phy_pclk0 clock.\n"); - return PTR_ERR(imxpriv->phy_pclk0); - } - imxpriv->phy_pclk1 = devm_clk_get(dev, "phy_pclk1"); - if (IS_ERR(imxpriv->phy_pclk1)) { - dev_err(dev, "can't get phy_pclk1 clock.\n"); - return PTR_ERR(imxpriv->phy_pclk1); - } - imxpriv->phy_apbclk = devm_clk_get(dev, "phy_apbclk"); - if (IS_ERR(imxpriv->phy_apbclk)) { - dev_err(dev, "can't get phy_apbclk clock.\n"); - return PTR_ERR(imxpriv->phy_apbclk); - } - - /* Fetch GPIO, then enable the external OSC */ - imxpriv->clkreq_gpiod = devm_gpiod_get_optional(dev, "clkreq", - GPIOD_OUT_LOW | GPIOD_FLAGS_BIT_NONEXCLUSIVE); - if (IS_ERR(imxpriv->clkreq_gpiod)) - return PTR_ERR(imxpriv->clkreq_gpiod); - if (imxpriv->clkreq_gpiod) - gpiod_set_consumer_name(imxpriv->clkreq_gpiod, "SATA CLKREQ"); - + if (!(dev->bus_dma_limit)) + dev->bus_dma_limit = DMA_BIT_MASK(32); + + imxpriv->sata_phy = devm_phy_get(dev, "sata-phy"); + if (IS_ERR(imxpriv->sata_phy)) + return dev_err_probe(dev, PTR_ERR(imxpriv->sata_phy), + "Failed to get sata_phy\n"); + + imxpriv->cali_phy0 = devm_phy_get(dev, "cali-phy0"); + if (IS_ERR(imxpriv->cali_phy0)) + return dev_err_probe(dev, PTR_ERR(imxpriv->cali_phy0), + "Failed to get cali_phy0\n"); + imxpriv->cali_phy1 = devm_phy_get(dev, "cali-phy1"); + if (IS_ERR(imxpriv->cali_phy1)) + return dev_err_probe(dev, PTR_ERR(imxpriv->cali_phy1), + "Failed to get cali_phy1\n"); return 0; } @@ -1077,12 +875,6 @@ static int imx_ahci_probe(struct platform_device *pdev) return PTR_ERR(imxpriv->sata_ref_clk); } - imxpriv->ahb_clk = devm_clk_get(dev, "ahb"); - if (IS_ERR(imxpriv->ahb_clk)) { - dev_err(dev, "can't get ahb clock.\n"); - return PTR_ERR(imxpriv->ahb_clk); - } - if (imxpriv->type == AHCI_IMX6Q || imxpriv->type == AHCI_IMX6QP) { u32 reg_value; @@ -1142,11 +934,8 @@ static int imx_ahci_probe(struct platform_device *pdev) goto disable_clk; /* - * Configure the HWINIT bits of the HOST_CAP and HOST_PORTS_IMPL, - * and IP vendor specific register IMX_TIMER1MS. - * Configure CAP_SSS (support stagered spin up). - * Implement the port0. - * Get the ahb clock rate, and configure the TIMER1MS register. + * Configure the HWINIT bits of the HOST_CAP and HOST_PORTS_IMPL. + * Set CAP_SSS (support stagered spin up) and Implement the port0. */ reg_val = readl(hpriv->mmio + HOST_CAP); if (!(reg_val & HOST_CAP_SSS)) { @@ -1159,8 +948,19 @@ static int imx_ahci_probe(struct platform_device *pdev) writel(reg_val, hpriv->mmio + HOST_PORTS_IMPL); } - reg_val = clk_get_rate(imxpriv->ahb_clk) / 1000; - writel(reg_val, hpriv->mmio + IMX_TIMER1MS); + if (imxpriv->type != AHCI_IMX8QM) { + /* + * Get AHB clock rate and configure the vendor specified + * TIMER1MS register on i.MX53, i.MX6Q and i.MX6QP only. + */ + imxpriv->ahb_clk = devm_clk_get(dev, "ahb"); + if (IS_ERR(imxpriv->ahb_clk)) { + dev_err(dev, "Failed to get ahb clock\n"); + goto disable_sata; + } + reg_val = clk_get_rate(imxpriv->ahb_clk) / 1000; + writel(reg_val, hpriv->mmio + IMX_TIMER1MS); + } ret = ahci_platform_init_host(pdev, hpriv, &ahci_imx_port_info, &ahci_platform_sht);
Clean up code by using PHY interface. Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com> --- drivers/ata/ahci_imx.c | 396 ++++++++++------------------------------- 1 file changed, 98 insertions(+), 298 deletions(-)