@@ -11,5 +11,53 @@ / {
model = "Emtop Embedded Solutions i.MX8M Mini Baseboard V1";
compatible = "ees,imx8mm-emtop-baseboard", "ees,imx8mm-emtop-som",
"fsl,imx8mm";
+};
+
+&fec1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_fec1>;
+ phy-mode = "rgmii-id";
+ phy-handle = <ðphy0>;
+ fsl,magic-packet;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy0: ethernet-phy@4 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <4>;
+ reset-gpios = <&gpio4 22 GPIO_ACTIVE_LOW>;
+ reset-assert-us = <10000>;
+ vddio-supply = <&vddio>;
+
+ vddio: vddio-regulator {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+ };
+ };
+};
+&iomuxc {
+ pinctrl_fec1: fec1grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_ENET_MDC_ENET1_MDC 0x3
+ MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO 0x3
+ MX8MM_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x1f
+ MX8MM_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x1f
+ MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x1f
+ MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x1f
+ MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x91
+ MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x91
+ MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x91
+ MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x91
+ MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x1f
+ MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x91
+ MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x91
+ MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x1f
+ MX8MM_IOMUXC_SAI2_RXC_GPIO4_IO22 0x19
+ >;
+ };
};
Change in V2 1. Add Board name into subject 2. Remove below properties - at803x,eee-disabled; - at803x,vddio-1p8v; Signed-off-by: Tarang Raval <tarang.raval@siliconsignals.io> --- .../dts/freescale/imx8mm-emtop-baseboard.dts | 48 +++++++++++++++++++ 1 file changed, 48 insertions(+)