@@ -902,6 +902,7 @@ static bool enetc_clean_tx_ring(struct enetc_bdr *tx_ring, int napi_budget)
if (unlikely(tx_frm_cnt && netif_carrier_ok(ndev) &&
__netif_subqueue_stopped(ndev, tx_ring->index) &&
+ !test_bit(ENETC_TX_DOWN, &priv->flags) &&
(enetc_bd_unused(tx_ring) >= ENETC_TXBDS_MAX_NEEDED))) {
netif_wake_subqueue(ndev, tx_ring->index);
}
@@ -1377,6 +1378,9 @@ int enetc_xdp_xmit(struct net_device *ndev, int num_frames,
int xdp_tx_bd_cnt, i, k;
int xdp_tx_frm_cnt = 0;
+ if (unlikely(test_bit(ENETC_TX_DOWN, &priv->flags)))
+ return -ENETDOWN;
+
enetc_lock_mdio();
tx_ring = priv->xdp_tx_ring[smp_processor_id()];
@@ -2223,18 +2227,24 @@ static void enetc_enable_rxbdr(struct enetc_hw *hw, struct enetc_bdr *rx_ring)
enetc_rxbdr_wr(hw, idx, ENETC_RBMR, rbmr);
}
-static void enetc_enable_bdrs(struct enetc_ndev_priv *priv)
+static void enetc_enable_rx_bdrs(struct enetc_ndev_priv *priv)
{
struct enetc_hw *hw = &priv->si->hw;
int i;
- for (i = 0; i < priv->num_tx_rings; i++)
- enetc_enable_txbdr(hw, priv->tx_ring[i]);
-
for (i = 0; i < priv->num_rx_rings; i++)
enetc_enable_rxbdr(hw, priv->rx_ring[i]);
}
+static void enetc_enable_tx_bdrs(struct enetc_ndev_priv *priv)
+{
+ struct enetc_hw *hw = &priv->si->hw;
+ int i;
+
+ for (i = 0; i < priv->num_tx_rings; i++)
+ enetc_enable_txbdr(hw, priv->tx_ring[i]);
+}
+
static void enetc_disable_rxbdr(struct enetc_hw *hw, struct enetc_bdr *rx_ring)
{
int idx = rx_ring->index;
@@ -2251,18 +2261,24 @@ static void enetc_disable_txbdr(struct enetc_hw *hw, struct enetc_bdr *rx_ring)
enetc_txbdr_wr(hw, idx, ENETC_TBMR, 0);
}
-static void enetc_disable_bdrs(struct enetc_ndev_priv *priv)
+static void enetc_disable_rx_bdrs(struct enetc_ndev_priv *priv)
{
struct enetc_hw *hw = &priv->si->hw;
int i;
- for (i = 0; i < priv->num_tx_rings; i++)
- enetc_disable_txbdr(hw, priv->tx_ring[i]);
-
for (i = 0; i < priv->num_rx_rings; i++)
enetc_disable_rxbdr(hw, priv->rx_ring[i]);
}
+static void enetc_disable_tx_bdrs(struct enetc_ndev_priv *priv)
+{
+ struct enetc_hw *hw = &priv->si->hw;
+ int i;
+
+ for (i = 0; i < priv->num_tx_rings; i++)
+ enetc_disable_txbdr(hw, priv->tx_ring[i]);
+}
+
static void enetc_wait_txbdr(struct enetc_hw *hw, struct enetc_bdr *tx_ring)
{
int delay = 8, timeout = 100;
@@ -2452,6 +2468,8 @@ void enetc_start(struct net_device *ndev)
enetc_setup_interrupts(priv);
+ enetc_enable_tx_bdrs(priv);
+
for (i = 0; i < priv->bdr_int_num; i++) {
int irq = pci_irq_vector(priv->si->pdev,
ENETC_BDR_INT_BASE_IDX + i);
@@ -2460,9 +2478,11 @@ void enetc_start(struct net_device *ndev)
enable_irq(irq);
}
- enetc_enable_bdrs(priv);
+ enetc_enable_rx_bdrs(priv);
netif_tx_start_all_queues(ndev);
+
+ clear_bit(ENETC_TX_DOWN, &priv->flags);
}
EXPORT_SYMBOL_GPL(enetc_start);
@@ -2520,9 +2540,11 @@ void enetc_stop(struct net_device *ndev)
struct enetc_ndev_priv *priv = netdev_priv(ndev);
int i;
+ set_bit(ENETC_TX_DOWN, &priv->flags);
+
netif_tx_stop_all_queues(ndev);
- enetc_disable_bdrs(priv);
+ enetc_disable_rx_bdrs(priv);
for (i = 0; i < priv->bdr_int_num; i++) {
int irq = pci_irq_vector(priv->si->pdev,
@@ -2535,6 +2557,8 @@ void enetc_stop(struct net_device *ndev)
enetc_wait_bdrs(priv);
+ enetc_disable_tx_bdrs(priv);
+
enetc_clear_interrupts(priv);
}
EXPORT_SYMBOL_GPL(enetc_stop);
@@ -325,6 +325,7 @@ enum enetc_active_offloads {
enum enetc_flags_bit {
ENETC_TX_ONESTEP_TSTAMP_IN_PROGRESS = 0,
+ ENETC_TX_DOWN,
};
/* interrupt coalescing modes */
When testing the XDP_REDIRECT function on the LS1028A platform, we found a very reproducible issue that the Tx frames can no longer be sent out even if XDP_REDIRECT is turned off. Specifically, if there is a lot of traffic on Rx direction, when XDP_REDIRECT is turned on, the console may display some warnings like "timeout for tx ring #6 clear", and all redirected frames will be dropped, the detaild log is as follows. root@ls1028ardb:~# ./xdp-bench redirect eno0 eno2 Redirecting from eno0 (ifindex 3; driver fsl_enetc) to eno2 (ifindex 4; driver fsl_enetc) [203.849809] fsl_enetc 0000:00:00.2 eno2: timeout for tx ring #5 clear [204.006051] fsl_enetc 0000:00:00.2 eno2: timeout for tx ring #6 clear [204.161944] fsl_enetc 0000:00:00.2 eno2: timeout for tx ring #7 clear eno0->eno2 1420505 rx/s 1420590 err,drop/s 0 xmit/s xmit eno0->eno2 0 xmit/s 1420590 drop/s 0 drv_err/s 15.71 bulk-avg eno0->eno2 1420484 rx/s 1420485 err,drop/s 0 xmit/s xmit eno0->eno2 0 xmit/s 1420485 drop/s 0 drv_err/s 15.71 bulk-avg By analyzing the XDP_REDIRECT implementation of enetc driver, we found two problems. First, enetc driver will reconfigure Tx and Rx BD rings when a bpf program is installed or uninstalled, but there is no mechanisms to block the redirected frames when enetc driver reconfigures BD rings. So introduce ENETC_TX_DOWN flag to prevent the redirected frames to be attached to Tx BD rings. Second, Tx BD rings are disabled first in enetc_stop() and then wait for empty. This operation is not safe while the Tx BD ring is actively transmitting frames, and will cause the ring to not be empty and hardware exception. As described in the block guide of LS1028A NETC, software should only disable an active ring after all pending ring entries have been consumed (i.e. when PI = CI). Disabling a transmit ring that is actively processing BDs risks a HW-SW race hazard whereby a hardware resource becomes assigned to work on one or more ring entries only to have those entries be removed due to the ring becoming disabled. So the correct behavior is that the software stops putting frames on the Tx BD rings (this is what ENETC_TX_DOWN does), then waits for the Tx BD rings to be empty, and finally disables the Tx BD rings. Fixes: c33bfaf91c4c ("net: enetc: set up XDP program under enetc_reconfigure()") Cc: stable@vger.kernel.org Signed-off-by: Wei Fang <wei.fang@nxp.com> Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> --- v2 changes: Remove a blank line from the end of enetc_disable_tx_bdrs(). --- drivers/net/ethernet/freescale/enetc/enetc.c | 44 +++++++++++++++----- drivers/net/ethernet/freescale/enetc/enetc.h | 1 + 2 files changed, 35 insertions(+), 10 deletions(-)