@@ -4535,10 +4535,8 @@ static int i9xx_crtc_mode_set(struct drm_crtc *crtc,
struct intel_encoder *encoder;
const intel_limit_t *limit;
int ret;
- struct fdi_m_n m_n = {0};
u32 reg, temp;
u32 lvds_sync = 0;
- int target_clock;
list_for_each_entry(encoder, &mode_config->encoder_list, base.head) {
if (encoder->base.crtc != crtc)
@@ -4580,9 +4578,6 @@ static int i9xx_crtc_mode_set(struct drm_crtc *crtc,
refclk / 1000);
} else if (!IS_GEN2(dev)) {
refclk = 96000;
- if (HAS_PCH_SPLIT(dev) &&
- (!has_edp_encoder || intel_encoder_is_pch_edp(&has_edp_encoder->base)))
- refclk = 120000; /* 120Mhz refclk */
} else {
refclk = 48000;
}
@@ -4639,143 +4634,6 @@ static int i9xx_crtc_mode_set(struct drm_crtc *crtc,
}
}
- /* FDI link */
- if (HAS_PCH_SPLIT(dev)) {
- int pixel_multiplier = intel_mode_get_pixel_multiplier(adjusted_mode);
- int lane = 0, link_bw, bpp;
- /* CPU eDP doesn't require FDI link, so just set DP M/N
- according to current link config */
- if (has_edp_encoder && !intel_encoder_is_pch_edp(&has_edp_encoder->base)) {
- target_clock = mode->clock;
- intel_edp_link_config(has_edp_encoder,
- &lane, &link_bw);
- } else {
- /* [e]DP over FDI requires target mode clock
- instead of link clock */
- if (is_dp || intel_encoder_is_pch_edp(&has_edp_encoder->base))
- target_clock = mode->clock;
- else
- target_clock = adjusted_mode->clock;
-
- /* FDI is a binary signal running at ~2.7GHz, encoding
- * each output octet as 10 bits. The actual frequency
- * is stored as a divider into a 100MHz clock, and the
- * mode pixel clock is stored in units of 1KHz.
- * Hence the bw of each lane in terms of the mode signal
- * is:
- */
- link_bw = intel_fdi_link_freq(dev) * MHz(100)/KHz(1)/10;
- }
-
- /* determine panel color depth */
- temp = I915_READ(PIPECONF(pipe));
- temp &= ~PIPE_BPC_MASK;
- if (is_lvds) {
- /* the BPC will be 6 if it is 18-bit LVDS panel */
- if ((I915_READ(PCH_LVDS) & LVDS_A3_POWER_MASK) == LVDS_A3_POWER_UP)
- temp |= PIPE_8BPC;
- else
- temp |= PIPE_6BPC;
- } else if (has_edp_encoder) {
- switch (dev_priv->edp.bpp/3) {
- case 8:
- temp |= PIPE_8BPC;
- break;
- case 10:
- temp |= PIPE_10BPC;
- break;
- case 6:
- temp |= PIPE_6BPC;
- break;
- case 12:
- temp |= PIPE_12BPC;
- break;
- }
- } else
- temp |= PIPE_8BPC;
- I915_WRITE(PIPECONF(pipe), temp);
-
- switch (temp & PIPE_BPC_MASK) {
- case PIPE_8BPC:
- bpp = 24;
- break;
- case PIPE_10BPC:
- bpp = 30;
- break;
- case PIPE_6BPC:
- bpp = 18;
- break;
- case PIPE_12BPC:
- bpp = 36;
- break;
- default:
- DRM_ERROR("unknown pipe bpc value\n");
- bpp = 24;
- }
-
- if (!lane) {
- /*
- * Account for spread spectrum to avoid
- * oversubscribing the link. Max center spread
- * is 2.5%; use 5% for safety's sake.
- */
- u32 bps = target_clock * bpp * 21 / 20;
- lane = bps / (link_bw * 8) + 1;
- }
-
- intel_crtc->fdi_lanes = lane;
-
- if (pixel_multiplier > 1)
- link_bw *= pixel_multiplier;
- ironlake_compute_m_n(bpp, lane, target_clock, link_bw, &m_n);
- }
-
- /* Ironlake: try to setup display ref clock before DPLL
- * enabling. This is only under driver's control after
- * PCH B stepping, previous chipset stepping should be
- * ignoring this setting.
- */
- if (HAS_PCH_SPLIT(dev)) {
- temp = I915_READ(PCH_DREF_CONTROL);
- /* Always enable nonspread source */
- temp &= ~DREF_NONSPREAD_SOURCE_MASK;
- temp |= DREF_NONSPREAD_SOURCE_ENABLE;
- temp &= ~DREF_SSC_SOURCE_MASK;
- temp |= DREF_SSC_SOURCE_ENABLE;
- I915_WRITE(PCH_DREF_CONTROL, temp);
-
- POSTING_READ(PCH_DREF_CONTROL);
- udelay(200);
-
- if (has_edp_encoder) {
- if (intel_panel_use_ssc(dev_priv)) {
- temp |= DREF_SSC1_ENABLE;
- I915_WRITE(PCH_DREF_CONTROL, temp);
-
- POSTING_READ(PCH_DREF_CONTROL);
- udelay(200);
- }
- temp &= ~DREF_CPU_SOURCE_OUTPUT_MASK;
-
- /* Enable CPU source on CPU attached eDP */
- if (!intel_encoder_is_pch_edp(&has_edp_encoder->base)) {
- if (intel_panel_use_ssc(dev_priv))
- temp |= DREF_CPU_SOURCE_OUTPUT_DOWNSPREAD;
- else
- temp |= DREF_CPU_SOURCE_OUTPUT_NONSPREAD;
- } else {
- /* Enable SSC on PCH eDP if needed */
- if (intel_panel_use_ssc(dev_priv)) {
- DRM_ERROR("enabling SSC on PCH\n");
- temp |= DREF_SUPERSPREAD_SOURCE_ENABLE;
- }
- }
- I915_WRITE(PCH_DREF_CONTROL, temp);
- POSTING_READ(PCH_DREF_CONTROL);
- udelay(200);
- }
- }
-
if (IS_PINEVIEW(dev)) {
fp = (1 << clock.n) << 16 | clock.m1 << 8 | clock.m2;
if (has_reduced_clock)
@@ -4788,25 +4646,7 @@ static int i9xx_crtc_mode_set(struct drm_crtc *crtc,
reduced_clock.m2;
}
- /* Enable autotuning of the PLL clock (if permissible) */
- if (HAS_PCH_SPLIT(dev)) {
- int factor = 21;
-
- if (is_lvds) {
- if ((intel_panel_use_ssc(dev_priv) &&
- dev_priv->lvds_ssc_freq == 100) ||
- (I915_READ(PCH_LVDS) & LVDS_CLKB_POWER_MASK) == LVDS_CLKB_POWER_UP)
- factor = 25;
- } else if (is_sdvo && is_tv)
- factor = 20;
-
- if (clock.m1 < factor * clock.n)
- fp |= FP_CB_TUNE;
- }
-
- dpll = 0;
- if (!HAS_PCH_SPLIT(dev))
- dpll = DPLL_VGA_MODE_DIS;
+ dpll = DPLL_VGA_MODE_DIS;
if (!IS_GEN2(dev)) {
if (is_lvds)
@@ -4818,12 +4658,10 @@ static int i9xx_crtc_mode_set(struct drm_crtc *crtc,
if (pixel_multiplier > 1) {
if (IS_I945G(dev) || IS_I945GM(dev) || IS_G33(dev))
dpll |= (pixel_multiplier - 1) << SDVO_MULTIPLIER_SHIFT_HIRES;
- else if (HAS_PCH_SPLIT(dev))
- dpll |= (pixel_multiplier - 1) << PLL_REF_SDVO_HDMI_MULTIPLIER_SHIFT;
}
dpll |= DPLL_DVO_HIGH_SPEED;
}
- if (is_dp || intel_encoder_is_pch_edp(&has_edp_encoder->base))
+ if (is_dp)
dpll |= DPLL_DVO_HIGH_SPEED;
/* compute bitmask from p1 value */
@@ -4831,9 +4669,6 @@ static int i9xx_crtc_mode_set(struct drm_crtc *crtc,
dpll |= (1 << (clock.p1 - 1)) << DPLL_FPA01_P1_POST_DIV_SHIFT_PINEVIEW;
else {
dpll |= (1 << (clock.p1 - 1)) << DPLL_FPA01_P1_POST_DIV_SHIFT;
- /* also FPA1 */
- if (HAS_PCH_SPLIT(dev))
- dpll |= (1 << (clock.p1 - 1)) << DPLL_FPA1_P1_POST_DIV_SHIFT;
if (IS_G4X(dev) && has_reduced_clock)
dpll |= (1 << (reduced_clock.p1 - 1)) << DPLL_FPA1_P1_POST_DIV_SHIFT;
}
@@ -4851,7 +4686,7 @@ static int i9xx_crtc_mode_set(struct drm_crtc *crtc,
dpll |= DPLLB_LVDS_P2_CLOCK_DIV_14;
break;
}
- if (INTEL_INFO(dev)->gen >= 4 && !HAS_PCH_SPLIT(dev))
+ if (INTEL_INFO(dev)->gen >= 4)
dpll |= (6 << PLL_LOAD_PULSE_PHASE_SHIFT);
} else {
if (is_lvds) {
@@ -4885,12 +4720,10 @@ static int i9xx_crtc_mode_set(struct drm_crtc *crtc,
/* Ironlake's plane is forced to pipe, bit 24 is to
enable color space conversion */
- if (!HAS_PCH_SPLIT(dev)) {
- if (pipe == 0)
- dspcntr &= ~DISPPLANE_SEL_PIPE_MASK;
- else
- dspcntr |= DISPPLANE_SEL_PIPE_B;
- }
+ if (pipe == 0)
+ dspcntr &= ~DISPPLANE_SEL_PIPE_MASK;
+ else
+ dspcntr |= DISPPLANE_SEL_PIPE_B;
if (pipe == 0 && INTEL_INFO(dev)->gen < 4) {
/* Enable pixel doubling when the dot clock is > 90% of the (display)
@@ -4906,23 +4739,16 @@ static int i9xx_crtc_mode_set(struct drm_crtc *crtc,
pipeconf &= ~PIPECONF_DOUBLE_WIDE;
}
- if (!HAS_PCH_SPLIT(dev))
- dpll |= DPLL_VCO_ENABLE;
+ dpll |= DPLL_VCO_ENABLE;
DRM_DEBUG_KMS("Mode for pipe %c:\n", pipe == 0 ? 'A' : 'B');
drm_mode_debug_printmodeline(mode);
- /* assign to Ironlake registers */
- if (HAS_PCH_SPLIT(dev)) {
- fp_reg = PCH_FP0(pipe);
- dpll_reg = PCH_DPLL(pipe);
- } else {
- fp_reg = FP0(pipe);
- dpll_reg = DPLL(pipe);
- }
+ fp_reg = FP0(pipe);
+ dpll_reg = DPLL(pipe);
/* PCH eDP needs FDI, but CPU eDP does not */
- if (!has_edp_encoder || intel_encoder_is_pch_edp(&has_edp_encoder->base)) {
+ if (!has_edp_encoder) {
I915_WRITE(fp_reg, fp);
I915_WRITE(dpll_reg, dpll & ~DPLL_VCO_ENABLE);
@@ -4930,50 +4756,19 @@ static int i9xx_crtc_mode_set(struct drm_crtc *crtc,
udelay(150);
}
- /* enable transcoder DPLL */
- if (HAS_PCH_CPT(dev)) {
- temp = I915_READ(PCH_DPLL_SEL);
- switch (pipe) {
- case 0:
- temp |= TRANSA_DPLL_ENABLE | TRANSA_DPLLA_SEL;
- break;
- case 1:
- temp |= TRANSB_DPLL_ENABLE | TRANSB_DPLLB_SEL;
- break;
- case 2:
- /* FIXME: manage transcoder PLLs? */
- temp |= TRANSC_DPLL_ENABLE | TRANSC_DPLLB_SEL;
- break;
- default:
- BUG();
- }
- I915_WRITE(PCH_DPLL_SEL, temp);
-
- POSTING_READ(PCH_DPLL_SEL);
- udelay(150);
- }
-
/* The LVDS pin pair needs to be on before the DPLLs are enabled.
* This is an exception to the general rule that mode_set doesn't turn
* things on.
*/
if (is_lvds) {
reg = LVDS;
- if (HAS_PCH_SPLIT(dev))
- reg = PCH_LVDS;
temp = I915_READ(reg);
temp |= LVDS_PORT_EN | LVDS_A0A2_CLKA_POWER_UP;
if (pipe == 1) {
- if (HAS_PCH_CPT(dev))
- temp |= PORT_TRANS_B_SEL_CPT;
- else
- temp |= LVDS_PIPEB_SELECT;
+ temp |= LVDS_PIPEB_SELECT;
} else {
- if (HAS_PCH_CPT(dev))
- temp &= ~PORT_TRANS_SEL_MASK;
- else
- temp &= ~LVDS_PIPEB_SELECT;
+ temp &= ~LVDS_PIPEB_SELECT;
}
/* set the corresponsding LVDS_BORDER bit */
temp |= dev_priv->lvds_border_bits;
@@ -4989,8 +4784,8 @@ static int i9xx_crtc_mode_set(struct drm_crtc *crtc,
* appropriately here, but we need to look more thoroughly into how
* panels behave in the two modes.
*/
- /* set the dithering flag on non-PCH LVDS as needed */
- if (INTEL_INFO(dev)->gen >= 4 && !HAS_PCH_SPLIT(dev)) {
+ /* set the dithering flag on LVDS as needed */
+ if (INTEL_INFO(dev)->gen >= 4) {
if (dev_priv->lvds_dither)
temp |= LVDS_ENABLE_DITHER;
else
@@ -5015,34 +4810,18 @@ static int i9xx_crtc_mode_set(struct drm_crtc *crtc,
I915_WRITE(reg, temp);
}
- /* set the dithering flag and clear for anything other than a panel. */
- if (HAS_PCH_SPLIT(dev)) {
- pipeconf &= ~PIPECONF_DITHER_EN;
- pipeconf &= ~PIPECONF_DITHER_TYPE_MASK;
- if (dev_priv->lvds_dither && (is_lvds || has_edp_encoder)) {
- pipeconf |= PIPECONF_DITHER_EN;
- pipeconf |= PIPECONF_DITHER_TYPE_ST1;
- }
- }
-
- if (is_dp || intel_encoder_is_pch_edp(&has_edp_encoder->base)) {
+ if (is_dp) {
intel_dp_set_m_n(crtc, mode, adjusted_mode);
- } else if (HAS_PCH_SPLIT(dev)) {
- /* For non-DP output, clear any trans DP clock recovery setting.*/
- I915_WRITE(TRANSDATA_M1(pipe), 0);
- I915_WRITE(TRANSDATA_N1(pipe), 0);
- I915_WRITE(TRANSDPLINK_M1(pipe), 0);
- I915_WRITE(TRANSDPLINK_N1(pipe), 0);
}
- if (!has_edp_encoder || intel_encoder_is_pch_edp(&has_edp_encoder->base)) {
+ if (!has_edp_encoder) {
I915_WRITE(dpll_reg, dpll);
/* Wait for the clocks to stabilize. */
POSTING_READ(dpll_reg);
udelay(150);
- if (INTEL_INFO(dev)->gen >= 4 && !HAS_PCH_SPLIT(dev)) {
+ if (INTEL_INFO(dev)->gen >= 4) {
temp = 0;
if (is_sdvo) {
temp = intel_mode_get_pixel_multiplier(adjusted_mode);
@@ -5113,30 +4892,16 @@ static int i9xx_crtc_mode_set(struct drm_crtc *crtc,
/* pipesrc and dspsize control the size that is scaled from,
* which should always be the user's requested size.
*/
- if (!HAS_PCH_SPLIT(dev)) {
- I915_WRITE(DSPSIZE(plane),
- ((mode->vdisplay - 1) << 16) |
- (mode->hdisplay - 1));
- I915_WRITE(DSPPOS(plane), 0);
- }
+ I915_WRITE(DSPSIZE(plane),
+ ((mode->vdisplay - 1) << 16) |
+ (mode->hdisplay - 1));
+ I915_WRITE(DSPPOS(plane), 0);
I915_WRITE(PIPESRC(pipe),
((mode->hdisplay - 1) << 16) | (mode->vdisplay - 1));
- if (HAS_PCH_SPLIT(dev)) {
- I915_WRITE(PIPE_DATA_M1(pipe), TU_SIZE(m_n.tu) | m_n.gmch_m);
- I915_WRITE(PIPE_DATA_N1(pipe), m_n.gmch_n);
- I915_WRITE(PIPE_LINK_M1(pipe), m_n.link_m);
- I915_WRITE(PIPE_LINK_N1(pipe), m_n.link_n);
-
- if (has_edp_encoder && !intel_encoder_is_pch_edp(&has_edp_encoder->base)) {
- ironlake_set_pll_edp(crtc, adjusted_mode->clock);
- }
- }
-
I915_WRITE(PIPECONF(pipe), pipeconf);
POSTING_READ(PIPECONF(pipe));
- if (!HAS_PCH_SPLIT(dev))
- intel_enable_pipe(dev_priv, pipe, false);
+ intel_enable_pipe(dev_priv, pipe, false);
intel_wait_for_vblank(dev, pipe);
@@ -5148,8 +4913,7 @@ static int i9xx_crtc_mode_set(struct drm_crtc *crtc,
I915_WRITE(DSPCNTR(plane), dspcntr);
POSTING_READ(DSPCNTR(plane));
- if (!HAS_PCH_SPLIT(dev))
- intel_enable_plane(dev_priv, plane, pipe);
+ intel_enable_plane(dev_priv, plane, pipe);
ret = intel_pipe_set_base(crtc, x, y, old_fb);