@@ -101,46 +101,57 @@ static void intel_dsi_pre_pll_enable(struct intel_encoder *encoder)
vlv_enable_dsi_pll(encoder);
}
-static void intel_dsi_pre_enable(struct intel_encoder *encoder)
+static void intel_dsi_device_ready(struct intel_encoder *encoder)
{
+ struct drm_i915_private *dev_priv = encoder->base.dev->dev_private;
+ struct intel_crtc *intel_crtc = to_intel_crtc(encoder->base.crtc);
+ int pipe = intel_crtc->pipe;
+ u32 val;
+
DRM_DEBUG_KMS("\n");
-}
-static void intel_dsi_enable(struct intel_encoder *encoder)
+ val = I915_READ(MIPI_PORT_CTRL(pipe));
+ I915_WRITE(MIPI_PORT_CTRL(pipe), val | LP_OUTPUT_HOLD);
+ usleep_range(1000, 1500);
+ I915_WRITE(MIPI_DEVICE_READY(pipe), DEVICE_READY | ULPS_STATE_EXIT);
+ usleep_range(2000, 2500);
+ I915_WRITE(MIPI_DEVICE_READY(pipe), DEVICE_READY);
+ usleep_range(2000, 2500);
+ I915_WRITE(MIPI_DEVICE_READY(pipe), 0x00);
+ usleep_range(2000, 2500);
+ I915_WRITE(MIPI_DEVICE_READY(pipe), DEVICE_READY);
+ usleep_range(2000, 2500);
+}
+static void intel_dsi_pre_enable(struct intel_encoder *encoder)
{
- struct drm_i915_private *dev_priv = encoder->base.dev->dev_private;
- struct intel_crtc *intel_crtc = to_intel_crtc(encoder->base.crtc);
struct intel_dsi *intel_dsi = enc_to_intel_dsi(&encoder->base);
- int pipe = intel_crtc->pipe;
- u32 temp;
DRM_DEBUG_KMS("\n");
if (intel_dsi->dev.dev_ops->panel_reset)
intel_dsi->dev.dev_ops->panel_reset(&intel_dsi->dev);
- temp = I915_READ(MIPI_DEVICE_READY(pipe));
- if ((temp & DEVICE_READY) == 0) {
- temp &= ~ULPS_STATE_MASK;
- I915_WRITE(MIPI_DEVICE_READY(pipe), temp | DEVICE_READY);
- } else if (temp & ULPS_STATE_MASK) {
- temp &= ~ULPS_STATE_MASK;
- I915_WRITE(MIPI_DEVICE_READY(pipe), temp | ULPS_STATE_EXIT);
- /*
- * We need to ensure that there is a minimum of 1 ms time
- * available before clearing the UPLS exit state.
- */
- msleep(2);
- I915_WRITE(MIPI_DEVICE_READY(pipe), temp);
- }
+ /* put device in ready state */
+ intel_dsi_device_ready(encoder);
if (intel_dsi->dev.dev_ops->send_otp_cmds)
intel_dsi->dev.dev_ops->send_otp_cmds(&intel_dsi->dev);
+}
+
+static void intel_dsi_enable(struct intel_encoder *encoder)
+{
+ struct drm_device *dev = encoder->base.dev;
+ struct drm_i915_private *dev_priv = dev->dev_private;
+ struct intel_crtc *intel_crtc = to_intel_crtc(encoder->base.crtc);
+ struct intel_dsi *intel_dsi = enc_to_intel_dsi(&encoder->base);
+ int pipe = intel_crtc->pipe;
+ u32 temp;
+
+ DRM_DEBUG_KMS("\n");
if (is_cmd_mode(intel_dsi))
I915_WRITE(MIPI_MAX_RETURN_PKT_SIZE(pipe), 8 * 4);
-
- if (is_vid_mode(intel_dsi)) {
+ else {
msleep(20); /* XXX */
dpi_send_cmd(intel_dsi, TURN_ON);
msleep(100);
@@ -157,7 +168,8 @@ static void intel_dsi_enable(struct intel_encoder *encoder)
static void intel_dsi_disable(struct intel_encoder *encoder)
{
- struct drm_i915_private *dev_priv = encoder->base.dev->dev_private;
+ struct drm_device *dev = encoder->base.dev;
+ struct drm_i915_private *dev_priv = dev->dev_private;
struct intel_crtc *intel_crtc = to_intel_crtc(encoder->base.crtc);
struct intel_dsi *intel_dsi = enc_to_intel_dsi(&encoder->base);
int pipe = intel_crtc->pipe;
@@ -165,8 +177,6 @@ static void intel_dsi_disable(struct intel_encoder *encoder)
DRM_DEBUG_KMS("\n");
- intel_dsi->dev.dev_ops->disable(&intel_dsi->dev);
-
if (is_vid_mode(intel_dsi)) {
dpi_send_cmd(intel_dsi, SHUTDOWN);
msleep(10);
@@ -179,20 +189,54 @@ static void intel_dsi_disable(struct intel_encoder *encoder)
msleep(2);
}
- temp = I915_READ(MIPI_DEVICE_READY(pipe));
- if (temp & DEVICE_READY) {
- temp &= ~DEVICE_READY;
- temp &= ~ULPS_STATE_MASK;
- I915_WRITE(MIPI_DEVICE_READY(pipe), temp);
- }
+ /* if disable packets are sent before sending shutdown packet then in
+ * some next enable sequence send turn on packet error is observed */
+ if (intel_dsi->dev.dev_ops->disable)
+ intel_dsi->dev.dev_ops->disable(&intel_dsi->dev);
}
-static void intel_dsi_post_disable(struct intel_encoder *encoder)
+static void intel_dsi_clear_device_ready(struct intel_encoder *encoder)
{
+ struct drm_i915_private *dev_priv = encoder->base.dev->dev_private;
+ struct intel_crtc *intel_crtc = to_intel_crtc(encoder->base.crtc);
+ int pipe = intel_crtc->pipe;
+ u32 val;
+
DRM_DEBUG_KMS("\n");
+ I915_WRITE(MIPI_DEVICE_READY(pipe), ULPS_STATE_ENTER);
+ usleep_range(2000, 2500);
+
+ I915_WRITE(MIPI_DEVICE_READY(pipe), ULPS_STATE_EXIT);
+ usleep_range(2000, 2500);
+
+ I915_WRITE(MIPI_DEVICE_READY(pipe), ULPS_STATE_ENTER);
+ usleep_range(2000, 2500);
+
+ val = I915_READ(MIPI_PORT_CTRL(pipe));
+ I915_WRITE(MIPI_PORT_CTRL(pipe), val & ~LP_OUTPUT_HOLD);
+ usleep_range(1000, 1500);
+
+ if (wait_for(((I915_READ(MIPI_PORT_CTRL(pipe)) & AFE_LATCHOUT)
+ == 0x00000), 30))
+ DRM_ERROR("DSI LP not going Low\n");
+
+ I915_WRITE(MIPI_DEVICE_READY(pipe), 0x00);
+ usleep_range(2000, 2500);
+
vlv_disable_dsi_pll(encoder);
}
+static void intel_dsi_post_disable(struct intel_encoder *encoder)
+{
+ struct intel_dsi *intel_dsi = enc_to_intel_dsi(&encoder->base);
+
+ DRM_DEBUG_KMS("\n");
+
+ intel_dsi_clear_device_ready(encoder);
+
+ if (intel_dsi->dev.dev_ops->disable_panel_power)
+ intel_dsi->dev.dev_ops->disable_panel_power(&intel_dsi->dev);
+}
static bool intel_dsi_get_hw_state(struct intel_encoder *encoder,
enum pipe *pipe)
@@ -41,6 +41,8 @@ struct intel_dsi_dev_ops {
void (*panel_reset)(struct intel_dsi_device *dsi);
+ void (*disable_panel_power)(struct intel_dsi_device *dsi);
+
/* one time programmable commands if needed */
void (*send_otp_cmds)(struct intel_dsi_device *dsi);
Basically ULPS handling during enable/disable has been moved to pre_enable and post_disable phases. PLL and panel power disable also has been moved to post_disable phase. The ULPS entry/exit sequneces as suggested by HW team is as follows - During enable time - set DEVICE_READY --> Clear DEVICE_READY --> set DEVICE_READY And during disable time to flush all FIFOs - set ENTER_SLEEP --> EXIT_SLEEP --> ENTER_SLEEP Also during disbale sequnece sub-encoder disable is moved to the end after port is disabled. v2: Based on comments from Ville - Detailed epxlaination in the commit messgae - Moved parameter changes out into another patch - Backlight enabling will be a new patch v3: Updated as per Jani's comments - Removed the I915_WRITE_BITS as it is not needed - Moved panel_reset and send_otp_cmds hooks to dsi_pre_enable - Moved disable_panel_power hook to dsi_post_disable - Replace hardcoding with AFE_LATCHOUT v4: Make intel_dsi_device_ready and intel_dsi_clear_device_ready static Signed-off-by: Yogesh Mohan Marimuthu <yogesh.mohan.marimuthu@intel.com> Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com> Reviewed-by: Jani Nikula <jani.nikula@intel.com> --- drivers/gpu/drm/i915/intel_dsi.c | 110 +++++++++++++++++++++++++++------------ drivers/gpu/drm/i915/intel_dsi.h | 2 + 2 files changed, 79 insertions(+), 33 deletions(-)