diff mbox

[GLK,MIPI,DSI,V5,1/8] drm/i915/glk: Program dphy param reg for GLK

Message ID 1487078180-15147-2-git-send-email-madhav.chauhan@intel.com (mailing list archive)
State New, archived
Headers show

Commit Message

Chauhan, Madhav Feb. 14, 2017, 1:16 p.m. UTC 
From: Deepak M <m.deepak@intel.com>

For GEMINILAKE, dphy param reg values are programmed in terms
of HS byte clock count while for older platforms in terms of
HS ddr clk count.

v2: Added comments to clarify ddr clock count calculation
v3: Use multiplier variable instead of IS_GEMINILAKE()
check everywhere (Jani)

Signed-off-by: Deepak M <m.deepak@intel.com>
Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
---
 drivers/gpu/drm/i915/intel_dsi_panel_vbt.c | 31 +++++++++++++++---------------
 1 file changed, 16 insertions(+), 15 deletions(-)

Comments

Jani Nikula Feb. 16, 2017, 2:47 p.m. UTC | #1 
On Tue, 14 Feb 2017, Madhav Chauhan <madhav.chauhan@intel.com> wrote:
> From: Deepak M <m.deepak@intel.com>
>
> For GEMINILAKE, dphy param reg values are programmed in terms
> of HS byte clock count while for older platforms in terms of
> HS ddr clk count.
>
> v2: Added comments to clarify ddr clock count calculation
> v3: Use multiplier variable instead of IS_GEMINILAKE()
> check everywhere (Jani)
>
> Signed-off-by: Deepak M <m.deepak@intel.com>
> Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>

Reviewed-by: Jani Nikula <jani.nikula@intel.com>

> ---
>  drivers/gpu/drm/i915/intel_dsi_panel_vbt.c | 31 +++++++++++++++---------------
>  1 file changed, 16 insertions(+), 15 deletions(-)
>
> diff --git a/drivers/gpu/drm/i915/intel_dsi_panel_vbt.c b/drivers/gpu/drm/i915/intel_dsi_panel_vbt.c
> index 8f683b8..d06e7f7 100644
> --- a/drivers/gpu/drm/i915/intel_dsi_panel_vbt.c
> +++ b/drivers/gpu/drm/i915/intel_dsi_panel_vbt.c
> @@ -571,6 +571,7 @@ struct drm_panel *vbt_panel_init(struct intel_dsi *intel_dsi, u16 panel_id)
>  	u32 tclk_prepare_clkzero, ths_prepare_hszero;
>  	u32 lp_to_hs_switch, hs_to_lp_switch;
>  	u32 pclk, computed_ddr;
> +	u32 mul;
>  	u16 burst_mode_ratio;
>  	enum port port;
>  
> @@ -674,11 +675,6 @@ struct drm_panel *vbt_panel_init(struct intel_dsi *intel_dsi, u16 panel_id)
>  		break;
>  	}
>  
> -	/*
> -	 * ui(s) = 1/f [f in hz]
> -	 * ui(ns) = 10^9 / (f*10^6) [f in Mhz] -> 10^3/f(Mhz)
> -	 */
> -
>  	/* in Kbps */
>  	ui_num = NS_KHZ_RATIO;
>  	ui_den = bitrate;
> @@ -692,21 +688,26 @@ struct drm_panel *vbt_panel_init(struct intel_dsi *intel_dsi, u16 panel_id)
>  	 */
>  	intel_dsi->lp_byte_clk = DIV_ROUND_UP(tlpx_ns * ui_den, 8 * ui_num);
>  
> -	/* count values in UI = (ns value) * (bitrate / (2 * 10^6))
> +	/* DDR clock period = 2 * UI
> +	 * UI(sec) = 1/(bitrate * 10^3) (bitrate is in KHZ)
> +	 * UI(nsec) = 10^6 / bitrate
> +	 * DDR clock period (nsec) = 2 * UI = (2 * 10^6)/ bitrate
> +	 * DDR clock count  = ns_value / DDR clock period
>  	 *
> -	 * Since txddrclkhs_i is 2xUI, all the count values programmed in
> -	 * DPHY param register are divided by 2
> -	 *
> -	 * prepare count
> +	 * For GEMINILAKE dphy_param_reg will be programmed in terms of
> +	 * HS byte clock count for other platform in HS ddr clock count
>  	 */
> +	mul = IS_GEMINILAKE(dev_priv) ? 8 : 2;
>  	ths_prepare_ns = max(mipi_config->ths_prepare,
>  			     mipi_config->tclk_prepare);
> -	prepare_cnt = DIV_ROUND_UP(ths_prepare_ns * ui_den, ui_num * 2);
> +
> +	/* prepare count */
> +	prepare_cnt = DIV_ROUND_UP(ths_prepare_ns * ui_den, ui_num * mul);
>  
>  	/* exit zero count */
>  	exit_zero_cnt = DIV_ROUND_UP(
>  				(ths_prepare_hszero - ths_prepare_ns) * ui_den,
> -				ui_num * 2
> +				ui_num * mul
>  				);
>  
>  	/*
> @@ -720,12 +721,12 @@ struct drm_panel *vbt_panel_init(struct intel_dsi *intel_dsi, u16 panel_id)
>  
>  	/* clk zero count */
>  	clk_zero_cnt = DIV_ROUND_UP(
> -			(tclk_prepare_clkzero -	ths_prepare_ns)
> -			* ui_den, 2 * ui_num);
> +				(tclk_prepare_clkzero -	ths_prepare_ns)
> +				* ui_den, ui_num * mul);
>  
>  	/* trail count */
>  	tclk_trail_ns = max(mipi_config->tclk_trail, mipi_config->ths_trail);
> -	trail_cnt = DIV_ROUND_UP(tclk_trail_ns * ui_den, 2 * ui_num);
> +	trail_cnt = DIV_ROUND_UP(tclk_trail_ns * ui_den, ui_num * mul);
>  
>  	if (prepare_cnt > PREPARE_CNT_MAX ||
>  		exit_zero_cnt > EXIT_ZERO_CNT_MAX ||
diff mbox

Patch

diff --git a/drivers/gpu/drm/i915/intel_dsi_panel_vbt.c b/drivers/gpu/drm/i915/intel_dsi_panel_vbt.c
index 8f683b8..d06e7f7 100644
--- a/drivers/gpu/drm/i915/intel_dsi_panel_vbt.c
+++ b/drivers/gpu/drm/i915/intel_dsi_panel_vbt.c
@@ -571,6 +571,7 @@  struct drm_panel *vbt_panel_init(struct intel_dsi *intel_dsi, u16 panel_id)
 	u32 tclk_prepare_clkzero, ths_prepare_hszero;
 	u32 lp_to_hs_switch, hs_to_lp_switch;
 	u32 pclk, computed_ddr;
+	u32 mul;
 	u16 burst_mode_ratio;
 	enum port port;
 
@@ -674,11 +675,6 @@  struct drm_panel *vbt_panel_init(struct intel_dsi *intel_dsi, u16 panel_id)
 		break;
 	}
 
-	/*
-	 * ui(s) = 1/f [f in hz]
-	 * ui(ns) = 10^9 / (f*10^6) [f in Mhz] -> 10^3/f(Mhz)
-	 */
-
 	/* in Kbps */
 	ui_num = NS_KHZ_RATIO;
 	ui_den = bitrate;
@@ -692,21 +688,26 @@  struct drm_panel *vbt_panel_init(struct intel_dsi *intel_dsi, u16 panel_id)
 	 */
 	intel_dsi->lp_byte_clk = DIV_ROUND_UP(tlpx_ns * ui_den, 8 * ui_num);
 
-	/* count values in UI = (ns value) * (bitrate / (2 * 10^6))
+	/* DDR clock period = 2 * UI
+	 * UI(sec) = 1/(bitrate * 10^3) (bitrate is in KHZ)
+	 * UI(nsec) = 10^6 / bitrate
+	 * DDR clock period (nsec) = 2 * UI = (2 * 10^6)/ bitrate
+	 * DDR clock count  = ns_value / DDR clock period
 	 *
-	 * Since txddrclkhs_i is 2xUI, all the count values programmed in
-	 * DPHY param register are divided by 2
-	 *
-	 * prepare count
+	 * For GEMINILAKE dphy_param_reg will be programmed in terms of
+	 * HS byte clock count for other platform in HS ddr clock count
 	 */
+	mul = IS_GEMINILAKE(dev_priv) ? 8 : 2;
 	ths_prepare_ns = max(mipi_config->ths_prepare,
 			     mipi_config->tclk_prepare);
-	prepare_cnt = DIV_ROUND_UP(ths_prepare_ns * ui_den, ui_num * 2);
+
+	/* prepare count */
+	prepare_cnt = DIV_ROUND_UP(ths_prepare_ns * ui_den, ui_num * mul);
 
 	/* exit zero count */
 	exit_zero_cnt = DIV_ROUND_UP(
 				(ths_prepare_hszero - ths_prepare_ns) * ui_den,
-				ui_num * 2
+				ui_num * mul
 				);
 
 	/*
@@ -720,12 +721,12 @@  struct drm_panel *vbt_panel_init(struct intel_dsi *intel_dsi, u16 panel_id)
 
 	/* clk zero count */
 	clk_zero_cnt = DIV_ROUND_UP(
-			(tclk_prepare_clkzero -	ths_prepare_ns)
-			* ui_den, 2 * ui_num);
+				(tclk_prepare_clkzero -	ths_prepare_ns)
+				* ui_den, ui_num * mul);
 
 	/* trail count */
 	tclk_trail_ns = max(mipi_config->tclk_trail, mipi_config->ths_trail);
-	trail_cnt = DIV_ROUND_UP(tclk_trail_ns * ui_den, 2 * ui_num);
+	trail_cnt = DIV_ROUND_UP(tclk_trail_ns * ui_den, ui_num * mul);
 
 	if (prepare_cnt > PREPARE_CNT_MAX ||
 		exit_zero_cnt > EXIT_ZERO_CNT_MAX ||