@@ -724,6 +724,18 @@ gen11_dsi_configure_transcoder(struct intel_encoder *encoder,
tmp |= VIDEO_MODE_SYNC_PULSE;
break;
}
+ } else {
+ /*
+ * FIXME: Retrieve this info from VBT.
+ * As per the spec when dsi transcoder is operating
+ * in TE GATE mode, TE comes from GPIO
+ * which is UTIL PIN for DSI 0.
+ * Also this GPIO would not be used for other
+ * purposes is an assumption.
+ */
+ tmp &= ~OP_MODE_MASK;
+ tmp |= CMD_MODE_TE_GATE;
+ tmp |= TE_SOURCE_GPIO;
}
I915_WRITE(DSI_TRANS_FUNC_CONF(dsi_trans), tmp);
@@ -991,6 +1003,32 @@ static void gen11_dsi_setup_timeouts(struct intel_encoder *encoder,
}
}
+static void gen11_dsi_config_util_pin(struct intel_encoder *encoder,
+ bool enable)
+{
+ struct drm_i915_private *dev_priv = to_i915(encoder->base.dev);
+ struct intel_dsi *intel_dsi = enc_to_intel_dsi(&encoder->base);
+ u32 tmp;
+
+ /*
+ * used as TE i/p for DSI0,
+ * for dual link/DSI1 TE is from slave DSI1
+ * through GPIO.
+ */
+ if (is_vid_mode(intel_dsi) || (intel_dsi->ports & BIT(PORT_B)))
+ return;
+
+ tmp = I915_READ(UTIL_PIN_CTL);
+
+ if (enable) {
+ tmp |= UTIL_PIN_DIRECTION_INPUT;
+ tmp |= UTIL_PIN_ENABLE;
+ } else {
+ tmp &= ~UTIL_PIN_ENABLE;
+ }
+ I915_WRITE(UTIL_PIN_CTL, tmp);
+}
+
static void
gen11_dsi_enable_port_and_phy(struct intel_encoder *encoder,
const struct intel_crtc_state *crtc_state)
@@ -1012,6 +1050,9 @@ gen11_dsi_enable_port_and_phy(struct intel_encoder *encoder,
/* setup D-PHY timings */
gen11_dsi_setup_dphy_timings(encoder, crtc_state);
+ /* Since transcoder is configured to take events from GPIO */
+ gen11_dsi_config_util_pin(encoder, true);
+
/* step 4h: setup DSI protocol timeouts */
gen11_dsi_setup_timeouts(encoder, crtc_state);
@@ -1144,6 +1185,15 @@ static void gen11_dsi_deconfigure_trancoder(struct intel_encoder *encoder)
enum transcoder dsi_trans;
u32 tmp;
+ /* disable periodic update mode */
+ if (is_cmd_mode(intel_dsi)) {
+ for_each_dsi_port(port, intel_dsi->ports) {
+ tmp = I915_READ(DSI_CMD_FRMCTL(port));
+ tmp &= ~DSI_PERIODIC_FRAME_UPDATE_ENABLE;
+ I915_WRITE(DSI_CMD_FRMCTL(port), tmp);
+ }
+ }
+
/* put dsi link in ULPS */
for_each_dsi_port(port, intel_dsi->ports) {
dsi_trans = dsi_port_to_transcoder(port);
@@ -1247,6 +1297,8 @@ static void gen11_dsi_disable(struct intel_encoder *encoder,
/* step3: disable port */
gen11_dsi_disable_port(encoder);
+ gen11_dsi_config_util_pin(encoder, false);
+
/* step4: disable IO power */
gen11_dsi_disable_io_power(encoder);
}
Configure the transcoder to operate in TE GATE command mode and take TE events from GPIO. Also disable the periodic command mode, that GOP would have programmed. v2: Disable util pin (Jani) Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com> --- drivers/gpu/drm/i915/display/icl_dsi.c | 52 ++++++++++++++++++++++++++ 1 file changed, 52 insertions(+)