@@ -849,14 +849,33 @@ gen11_dsi_set_transcoder_timings(struct intel_encoder *encoder,
}
hactive = adjusted_mode->crtc_hdisplay;
- htotal = DIV_ROUND_UP(adjusted_mode->crtc_htotal * mul, div);
+
+ if (is_vid_mode(intel_dsi))
+ htotal = DIV_ROUND_UP(adjusted_mode->crtc_htotal * mul, div);
+ else
+ htotal = DIV_ROUND_UP((hactive + 160) * mul, div);
+
hsync_start = DIV_ROUND_UP(adjusted_mode->crtc_hsync_start * mul, div);
hsync_end = DIV_ROUND_UP(adjusted_mode->crtc_hsync_end * mul, div);
hsync_size = hsync_end - hsync_start;
hback_porch = (adjusted_mode->crtc_htotal -
adjusted_mode->crtc_hsync_end);
vactive = adjusted_mode->crtc_vdisplay;
- vtotal = adjusted_mode->crtc_vtotal;
+
+ if (is_vid_mode(intel_dsi)) {
+ vtotal = adjusted_mode->crtc_vtotal;
+ } else {
+ int bpp, line_time_us, byte_clk_period_ns;
+
+ if (crtc_state->dsc.compression_enable)
+ bpp = crtc_state->dsc.compressed_bpp;
+ else
+ bpp = mipi_dsi_pixel_format_to_bpp(intel_dsi->pixel_format);
+
+ byte_clk_period_ns = 1000000 / afe_clk(encoder, crtc_state);
+ line_time_us = (htotal * (bpp / 8) * byte_clk_period_ns) / (1000 * intel_dsi->lane_count);
+ vtotal = vactive + DIV_ROUND_UP(400, line_time_us);
+ }
vsync_start = adjusted_mode->crtc_vsync_start;
vsync_end = adjusted_mode->crtc_vsync_end;
vsync_shift = hsync_start - htotal / 2;
@@ -885,7 +904,7 @@ gen11_dsi_set_transcoder_timings(struct intel_encoder *encoder,
}
/* TRANS_HSYNC register to be programmed only for video mode */
- if (intel_dsi->operation_mode == INTEL_DSI_VIDEO_MODE) {
+ if (is_vid_mode(intel_dsi)) {
if (intel_dsi->video_mode_format ==
VIDEO_MODE_NON_BURST_WITH_SYNC_PULSE) {
/* BSPEC: hsync size should be atleast 16 pixels */
@@ -928,22 +947,27 @@ gen11_dsi_set_transcoder_timings(struct intel_encoder *encoder,
if (vsync_start < vactive)
drm_err(&dev_priv->drm, "vsync_start less than vactive\n");
- /* program TRANS_VSYNC register */
- for_each_dsi_port(port, intel_dsi->ports) {
- dsi_trans = dsi_port_to_transcoder(port);
- intel_de_write(dev_priv, VSYNC(dsi_trans),
- (vsync_start - 1) | ((vsync_end - 1) << 16));
+ /* program TRANS_VSYNC register for video mode only */
+ if (is_vid_mode(intel_dsi)) {
+ for_each_dsi_port(port, intel_dsi->ports) {
+ dsi_trans = dsi_port_to_transcoder(port);
+ intel_de_write(dev_priv, VSYNC(dsi_trans),
+ (vsync_start - 1) | ((vsync_end - 1) << 16));
+ }
}
/*
- * FIXME: It has to be programmed only for interlaced
+ * FIXME: It has to be programmed only for video modes and interlaced
* modes. Put the check condition here once interlaced
* info available as described above.
* program TRANS_VSYNCSHIFT register
*/
- for_each_dsi_port(port, intel_dsi->ports) {
- dsi_trans = dsi_port_to_transcoder(port);
- intel_de_write(dev_priv, VSYNCSHIFT(dsi_trans), vsync_shift);
+ if (is_vid_mode(intel_dsi)) {
+ for_each_dsi_port(port, intel_dsi->ports) {
+ dsi_trans = dsi_port_to_transcoder(port);
+ intel_de_write(dev_priv, VSYNCSHIFT(dsi_trans),
+ vsync_shift);
+ }
}
/* program TRANS_VBLANK register, should be same as vtotal programmed */
Transcoder timing calculation differ for command mode. v2: Use is_vid_mode, and use same I915_WRITE (Jani) v3: Adjust the calculations to reflect dsc compression ratio v4: Rearrange the vertical and horizontal timing calc, optimize local variables usage. (Jani) v5: Fix the values used for calculation, use afe_clk for byte clock calculation, use intel_de_write/read (Jani) Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com> --- drivers/gpu/drm/i915/display/icl_dsi.c | 48 +++++++++++++++++++------- 1 file changed, 36 insertions(+), 12 deletions(-)