new file mode 100644
@@ -0,0 +1,81 @@
+/* SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note */
+#ifndef _UAPI_ASM_X86_DEBUGREG_H
+#define _UAPI_ASM_X86_DEBUGREG_H
+
+
+/* Indicate the register numbers for a number of the specific
+ debug registers. Registers 0-3 contain the addresses we wish to trap on */
+#define DR_FIRSTADDR 0 /* u_debugreg[DR_FIRSTADDR] */
+#define DR_LASTADDR 3 /* u_debugreg[DR_LASTADDR] */
+
+#define DR_STATUS 6 /* u_debugreg[DR_STATUS] */
+#define DR_CONTROL 7 /* u_debugreg[DR_CONTROL] */
+
+/* Define a few things for the status register. We can use this to determine
+ which debugging register was responsible for the trap. The other bits
+ are either reserved or not of interest to us. */
+
+/* Define reserved bits in DR6 which are always set to 1 */
+#define DR6_RESERVED (0xFFFF0FF0)
+
+#define DR_TRAP0 (0x1) /* db0 */
+#define DR_TRAP1 (0x2) /* db1 */
+#define DR_TRAP2 (0x4) /* db2 */
+#define DR_TRAP3 (0x8) /* db3 */
+#define DR_TRAP_BITS (DR_TRAP0|DR_TRAP1|DR_TRAP2|DR_TRAP3)
+
+#define DR_STEP (0x4000) /* single-step */
+#define DR_SWITCH (0x8000) /* task switch */
+
+/* Now define a bunch of things for manipulating the control register.
+ The top two bytes of the control register consist of 4 fields of 4
+ bits - each field corresponds to one of the four debug registers,
+ and indicates what types of access we trap on, and how large the data
+ field is that we are looking at */
+
+#define DR_CONTROL_SHIFT 16 /* Skip this many bits in ctl register */
+#define DR_CONTROL_SIZE 4 /* 4 control bits per register */
+
+#define DR_RW_EXECUTE (0x0) /* Settings for the access types to trap on */
+#define DR_RW_WRITE (0x1)
+#define DR_RW_READ (0x3)
+
+#define DR_LEN_1 (0x0) /* Settings for data length to trap on */
+#define DR_LEN_2 (0x4)
+#define DR_LEN_4 (0xC)
+#define DR_LEN_8 (0x8)
+
+/* The low byte to the control register determine which registers are
+ enabled. There are 4 fields of two bits. One bit is "local", meaning
+ that the processor will reset the bit after a task switch and the other
+ is global meaning that we have to explicitly reset the bit. With linux,
+ you can use either one, since we explicitly zero the register when we enter
+ kernel mode. */
+
+#define DR_LOCAL_ENABLE_SHIFT 0 /* Extra shift to the local enable bit */
+#define DR_GLOBAL_ENABLE_SHIFT 1 /* Extra shift to the global enable bit */
+#define DR_LOCAL_ENABLE (0x1) /* Local enable for reg 0 */
+#define DR_GLOBAL_ENABLE (0x2) /* Global enable for reg 0 */
+#define DR_ENABLE_SIZE 2 /* 2 enable bits per register */
+
+#define DR_LOCAL_ENABLE_MASK (0x55) /* Set local bits for all 4 regs */
+#define DR_GLOBAL_ENABLE_MASK (0xAA) /* Set global bits for all 4 regs */
+
+/* The second byte to the control register has a few special things.
+ We can slow the instruction pipeline for instructions coming via the
+ gdt or the ldt if we want to. I am not sure why this is an advantage */
+
+#ifdef __i386__
+#define DR_CONTROL_RESERVED (0xFC00) /* Reserved by Intel */
+#else
+#define DR_CONTROL_RESERVED (0xFFFFFFFF0000FC00UL) /* Reserved */
+#endif
+
+#define DR_LOCAL_SLOWDOWN (0x100) /* Local slow the pipeline */
+#define DR_GLOBAL_SLOWDOWN (0x200) /* Global slow the pipeline */
+
+/*
+ * HW breakpoint additions
+ */
+
+#endif /* _UAPI_ASM_X86_DEBUGREG_H */
x86/vmx_tests.c depends on the kernel header and can't be compiled otherwise on x86_64-elf gcc on macOS. Cc: Jim Mattson <jmattson@google.com> Cc: Peter Shier <pshier@google.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Cameron Esfahani <dirty@apple.com> Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com> --- lib/x86/asm/debugreg.h | 81 ++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 81 insertions(+) create mode 100644 lib/x86/asm/debugreg.h