@@ -850,7 +850,7 @@ in-kernel irqchip (GIC), and for in-kernel irqchip can tell the GIC to
use PPIs designated for specific cpus. The irq field is interpreted
like this::
- bits: | 31 ... 28 | 27 ... 24 | 23 ... 16 | 15 ... 0 |
+ bits: | 31 ... 28 | 27 ... 24 | 23 ... 16 | 15 ... 0 |
field: | vcpu2_index | irq_type | vcpu_index | irq_id |
The irq_type field has the following values:
@@ -2144,10 +2144,10 @@ prior to calling the KVM_RUN ioctl.
Errors:
====== ============================================================
- ENOENT no such register
- EINVAL invalid register ID, or no such register or used with VMs in
+ ENOENT no such register
+ EINVAL invalid register ID, or no such register or used with VMs in
protected virtualization mode on s390
- EPERM (arm64) register access not allowed before vcpu finalization
+ EPERM (arm64) register access not allowed before vcpu finalization
====== ============================================================
(These error codes are indicative only: do not rely on a specific error
@@ -2585,10 +2585,10 @@ following id bit patterns::
Errors include:
======== ============================================================
- ENOENT no such register
- EINVAL invalid register ID, or no such register or used with VMs in
+ ENOENT no such register
+ EINVAL invalid register ID, or no such register or used with VMs in
protected virtualization mode on s390
- EPERM (arm64) register access not allowed before vcpu finalization
+ EPERM (arm64) register access not allowed before vcpu finalization
======== ============================================================
(These error codes are indicative only: do not rely on a specific error
@@ -3107,13 +3107,13 @@ current state. "addr" is ignored.
Errors:
====== =================================================================
- EINVAL the target is unknown, or the combination of features is invalid.
- ENOENT a features bit specified is unknown.
+ EINVAL the target is unknown, or the combination of features is invalid.
+ ENOENT a features bit specified is unknown.
====== =================================================================
This tells KVM what type of CPU to present to the guest, and what
-optional features it should have. This will cause a reset of the cpu
-registers to their initial values. If this is not called, KVM_RUN will
+optional features it should have. This will cause a reset of the cpu
+registers to their initial values. If this is not called, KVM_RUN will
return ENOEXEC for that vcpu.
The initial values are defined as:
@@ -3234,8 +3234,8 @@ VCPU matching underlying host.
Errors:
===== ==============================================================
- E2BIG the reg index list is too big to fit in the array specified by
- the user (the number required will be written into n).
+ E2BIG the reg index list is too big to fit in the array specified by
+ the user (the number required will be written into n).
===== ==============================================================
::
@@ -3283,7 +3283,7 @@ specific device.
ARM/arm64 divides the id field into two parts, a device id and an
address type id specific to the individual device::
- bits: | 63 ... 32 | 31 ... 16 | 15 ... 0 |
+ bits: | 63 ... 32 | 31 ... 16 | 15 ... 0 |
field: | 0x00000000 | device id | addr type id |
ARM/arm64 currently only require this when using the in-kernel GIC
@@ -26,12 +26,12 @@ this document is built on this example)::
Terminology:
-- L0 – level-0; the bare metal host, running KVM
+- L0 - level-0; the bare metal host, running KVM
-- L1 – level-1 guest; a VM running on L0; also called the "guest
+- L1 - level-1 guest; a VM running on L0; also called the "guest
hypervisor", as it itself is capable of running KVM.
-- L2 – level-2 guest; a VM running on L1, this is the "nested guest"
+- L2 - level-2 guest; a VM running on L1, this is the "nested guest"
.. note:: The above diagram is modelled after the x86 architecture;
s390x, ppc64 and other architectures are likely to have
@@ -39,7 +39,7 @@ Terminology:
For example, s390x always has an LPAR (LogicalPARtition)
hypervisor running on bare metal, adding another layer and
- resulting in at least four levels in a nested setup — L0 (bare
+ resulting in at least four levels in a nested setup - L0 (bare
metal, running the LPAR hypervisor), L1 (host hypervisor), L2
(guest hypervisor), L3 (nested guest).
@@ -167,11 +167,11 @@ Enabling "nested" (s390x)
$ modprobe kvm nested=1
.. note:: On s390x, the kernel parameter ``hpage`` is mutually exclusive
- with the ``nested`` paramter — i.e. to be able to enable
+ with the ``nested`` paramter - i.e. to be able to enable
``nested``, the ``hpage`` parameter *must* be disabled.
2. The guest hypervisor (L1) must be provided with the ``sie`` CPU
- feature — with QEMU, this can be done by using "host passthrough"
+ feature - with QEMU, this can be done by using "host passthrough"
(via the command-line ``-cpu host``).
3. Now the KVM module can be loaded in the L1 (guest hypervisor)::
While UTF-8 characters can be used at the Linux documentation, the best is to use them only when ASCII doesn't offer a good replacement. So, replace the occurences of the following UTF-8 characters: - U+00a0 (' '): NO-BREAK SPACE - U+2013 ('–'): EN DASH - U+2014 ('—'): EM DASH Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> --- Documentation/virt/kvm/api.rst | 28 +++++++++---------- .../virt/kvm/running-nested-guests.rst | 12 ++++---- 2 files changed, 20 insertions(+), 20 deletions(-)