new file mode 100644
@@ -0,0 +1,33 @@
+Hisilicon Hip06 low-pin-count device
+ Hisilicon Hip06 SoCs implement a Low Pin Count (LPC) controller, which
+ provides I/O access to some legacy ISA devices.
+ Hip06 is based on arm64 architecture where there is no I/O space. So, the
+ I/O ports here are not cpu addresses, and there is no 'ranges' property in
+ LPC device node.
+
+Required properties:
+- compatible: value should be as follows:
+ (a) "hisilicon,hip06-lpc"
+ (b) "hisilicon,hip07-lpc"
+- #address-cells: must be 2 which stick to the ISA/EISA binding doc.
+- #size-cells: must be 1 which stick to the ISA/EISA binding doc.
+- reg: base memory range where the LPC register set is mapped.
+
+Note:
+ The node name before '@' must be "isa" to represent the binding stick to the
+ ISA/EISA binding specification.
+
+Example:
+
+isa@a01b0000 {
+ compatible = "hisilicon,hip06-lpc";
+ #address-cells = <2>;
+ #size-cells = <1>;
+ reg = <0x0 0xa01b0000 0x0 0x1000>;
+
+ ipmi0: bt@e4 {
+ compatible = "ipmi-bt";
+ device_type = "ipmi";
+ reg = <0x01 0xe4 0x04>;
+ };
+};
@@ -65,6 +65,14 @@ config BRCMSTB_GISB_ARB
arbiter. This driver provides timeout and target abort error handling
and internal bus master decoding.
+config HISILICON_LPC
+ bool "Support for ISA I/O space on Hisilicon hip06/7"
+ depends on (ARM64 && (ARCH_HISI || COMPILE_TEST))
+ select INDIRECT_PIO
+ help
+ Driver needed for some legacy ISA devices attached to Low-Pin-Count
+ on Hisilicon hip06/7 SoC.
+
config IMX_WEIM
bool "Freescale EIM DRIVER"
depends on ARCH_MXC
@@ -8,6 +8,7 @@ obj-$(CONFIG_ARM_CCI) += arm-cci.o
obj-$(CONFIG_ARM_CCN) += arm-ccn.o
obj-$(CONFIG_BRCMSTB_GISB_ARB) += brcmstb_gisb.o
+obj-$(CONFIG_HISILICON_LPC) += hisi_lpc.o
obj-$(CONFIG_IMX_WEIM) += imx-weim.o
obj-$(CONFIG_MIPS_CDMM) += mips_cdmm.o
obj-$(CONFIG_MVEBU_MBUS) += mvebu-mbus.o
new file mode 100644
@@ -0,0 +1,507 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2017 Hisilicon Limited, All Rights Reserved.
+ * Author: Zhichang Yuan <yuanzhichang@hisilicon.com>
+ * Author: Zou Rongrong <zourongrong@huawei.com>
+ * Author: John Garry <john.garry@huawei.com>
+ *
+ */
+
+#include <linux/acpi.h>
+#include <linux/console.h>
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/logic_pio.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/of_platform.h>
+#include <linux/pci.h>
+#include <linux/slab.h>
+
+/*
+ * Setting this bit means each IO operation will target to a
+ * different port address:
+ * 0 means repeatedly IO operations will stick on the same port,
+ * such as BT;
+ */
+#define FG_INCRADDR_LPC 0x02
+
+struct lpc_cycle_para {
+ unsigned int opflags;
+ unsigned int csize; /* the data length of each operation */
+};
+
+struct hisilpc_dev {
+ spinlock_t cycle_lock;
+ void __iomem *membase;
+ struct logic_pio_hwaddr *io_host;
+};
+
+/* The maximum continuous cycles per burst */
+#define LPC_MAX_BURST 16
+/* The IO cycle counts supported is four per operation at maximum */
+#define LPC_MAX_DULEN 4
+#if LPC_MAX_DULEN > LPC_MAX_BURST
+#error "LPC.. MAX_DULEN must be not bigger than MAX_OPCNT!"
+#endif
+
+#if LPC_MAX_BURST % LPC_MAX_DULEN
+#error "LPC.. LPC_MAX_BURST must be multiple of LPC_MAX_DULEN!"
+#endif
+
+#define LPC_REG_START 0x00 /* start a new LPC cycle */
+#define LPC_REG_OP_STATUS 0x04 /* the current LPC status */
+#define LPC_REG_IRQ_ST 0x08 /* interrupt enable&status */
+#define LPC_REG_OP_LEN 0x10 /* how many LPC cycles each start */
+#define LPC_REG_CMD 0x14 /* command for the required LPC cycle */
+#define LPC_REG_ADDR 0x20 /* LPC target address */
+#define LPC_REG_WDATA 0x24 /* data to be written */
+#define LPC_REG_RDATA 0x28 /* data coming from peer */
+
+
+/* The command register fields */
+#define LPC_CMD_SAMEADDR 0x08
+#define LPC_CMD_TYPE_IO 0x00
+#define LPC_CMD_WRITE 0x01
+#define LPC_CMD_READ 0x00
+/* the bit attribute is W1C. 1 represents OK. */
+#define LPC_STAT_BYIRQ 0x02
+
+#define LPC_STATUS_IDLE 0x01
+#define LPC_OP_FINISHED 0x02
+
+#define LPC_START_WORK 0x01
+
+/* The minimal nanosecond interval for each query on LPC cycle status. */
+#define LPC_NSEC_PERWAIT 100
+/*
+ * The maximum waiting time is about 128us.
+ * It is specific for stream I/O, such as ins.
+ * The fastest IO cycle time is about 390ns, but the worst case will wait
+ * for extra 256 lpc clocks, so (256 + 13) * 30ns = 8 us. The maximum
+ * burst cycles is 16. So, the maximum waiting time is about 128us under
+ * worst case.
+ * choose 1300 as the maximum.
+ */
+#define LPC_MAX_WAITCNT 1300
+/* About 10us. This is specific for single IO operation, such as inb. */
+#define LPC_PEROP_WAITCNT 100
+
+static inline int wait_lpc_idle(unsigned char *mbase,
+ unsigned int waitcnt) {
+ u32 opstatus;
+
+ while (waitcnt--) {
+ ndelay(LPC_NSEC_PERWAIT);
+ opstatus = readl(mbase + LPC_REG_OP_STATUS);
+ if (opstatus & LPC_STATUS_IDLE)
+ return (opstatus & LPC_OP_FINISHED) ? 0 : (-EIO);
+ }
+ return -ETIME;
+}
+
+/*
+ * hisilpc_target_in - trigger a series of lpc cycles to read required data
+ * from target peripheral.
+ * @lpcdev: pointer to hisi lpc device
+ * @para: some parameters used to control the lpc I/O operations
+ * @ptaddr: the lpc I/O target port address
+ * @buf: where the read back data is stored
+ * @opcnt: how many I/O operations required in this calling
+ *
+ * Only one byte data is read each I/O operation.
+ *
+ * Returns 0 on success, non-zero on fail.
+ */
+static int
+hisilpc_target_in(struct hisilpc_dev *lpcdev, struct lpc_cycle_para *para,
+ unsigned long ptaddr, unsigned char *buf,
+ unsigned long opcnt)
+{
+ unsigned long cnt_per_trans;
+ unsigned int cmd_word;
+ unsigned int waitcnt;
+ int ret;
+
+ if (!buf || !opcnt || !para || !para->csize || !lpcdev)
+ return -EINVAL;
+
+ cmd_word = LPC_CMD_TYPE_IO | LPC_CMD_READ;
+ waitcnt = LPC_PEROP_WAITCNT;
+ if (!(para->opflags & FG_INCRADDR_LPC)) {
+ cmd_word |= LPC_CMD_SAMEADDR;
+ waitcnt = LPC_MAX_WAITCNT;
+ }
+
+ ret = 0;
+ cnt_per_trans = (para->csize == 1) ? opcnt : para->csize;
+ for (; opcnt && !ret; cnt_per_trans = para->csize) {
+ unsigned long flags;
+
+ /* whole operation must be atomic */
+ spin_lock_irqsave(&lpcdev->cycle_lock, flags);
+
+ writel_relaxed(cnt_per_trans, lpcdev->membase + LPC_REG_OP_LEN);
+
+ writel_relaxed(cmd_word, lpcdev->membase + LPC_REG_CMD);
+
+ writel_relaxed(ptaddr, lpcdev->membase + LPC_REG_ADDR);
+
+ writel(LPC_START_WORK, lpcdev->membase + LPC_REG_START);
+
+ /* whether the operation is finished */
+ ret = wait_lpc_idle(lpcdev->membase, waitcnt);
+ if (!ret) {
+ opcnt -= cnt_per_trans;
+ for (cnt_per_trans--; cnt_per_trans--; buf++)
+ *buf = readb_relaxed(lpcdev->membase +
+ LPC_REG_RDATA);
+ *buf = readb(lpcdev->membase + LPC_REG_RDATA);
+ }
+
+ spin_unlock_irqrestore(&lpcdev->cycle_lock, flags);
+ }
+
+ return ret;
+}
+
+/*
+ * hisilpc_target_out - trigger a series of lpc cycles to write required
+ * data to target peripheral.
+ * @lpcdev: pointer to hisi lpc device
+ * @para: some parameters used to control the lpc I/O operations
+ * @ptaddr: the lpc I/O target port address
+ * @buf: where the data to be written is stored
+ * @opcnt: how many I/O operations required
+ *
+ * Only one byte data is read each I/O operation.
+ *
+ * Returns 0 on success, non-zero on fail.
+ *
+ */
+static int
+hisilpc_target_out(struct hisilpc_dev *lpcdev, struct lpc_cycle_para *para,
+ unsigned long ptaddr, const unsigned char *buf,
+ unsigned long opcnt)
+{
+ unsigned long cnt_per_trans;
+ unsigned int cmd_word;
+ unsigned int waitcnt;
+ int ret;
+
+ if (!buf || !opcnt || !para || !lpcdev)
+ return -EINVAL;
+
+ /* default is increasing address */
+ cmd_word = LPC_CMD_TYPE_IO | LPC_CMD_WRITE;
+ waitcnt = LPC_PEROP_WAITCNT;
+ if (!(para->opflags & FG_INCRADDR_LPC)) {
+ cmd_word |= LPC_CMD_SAMEADDR;
+ waitcnt = LPC_MAX_WAITCNT;
+ }
+
+ ret = 0;
+ cnt_per_trans = (para->csize == 1) ? opcnt : para->csize;
+ for (; opcnt && !ret; cnt_per_trans = para->csize) {
+ unsigned long flags;
+
+ spin_lock_irqsave(&lpcdev->cycle_lock, flags);
+
+ writel_relaxed(cnt_per_trans, lpcdev->membase + LPC_REG_OP_LEN);
+ writel_relaxed(cmd_word, lpcdev->membase + LPC_REG_CMD);
+ writel_relaxed(ptaddr, lpcdev->membase + LPC_REG_ADDR);
+
+ opcnt -= cnt_per_trans;
+ for (; cnt_per_trans--; buf++)
+ writeb_relaxed(*buf, lpcdev->membase + LPC_REG_WDATA);
+
+ writel(LPC_START_WORK, lpcdev->membase + LPC_REG_START);
+
+ /* whether the operation is finished */
+ ret = wait_lpc_idle(lpcdev->membase, waitcnt);
+
+ spin_unlock_irqrestore(&lpcdev->cycle_lock, flags);
+ }
+
+ return ret;
+}
+
+static inline unsigned long
+hisi_lpc_pio_to_addr(struct hisilpc_dev *lpcdev, unsigned long pio)
+{
+ return pio - lpcdev->io_host->io_start +
+ lpcdev->io_host->hw_start;
+}
+
+
+/**
+ * hisilpc_comm_in - read/input the data from the I/O peripheral
+ * through LPC.
+ * @devobj: pointer to the device information relevant to LPC controller.
+ * @pio: the target I/O port address.
+ * @dlen: the data length required to read from the target I/O port.
+ *
+ * when succeed, the data read back is stored in buffer pointed by inbuf.
+ * For inb, return the data read from I/O or -1 when error occur.
+ */
+static u32 hisilpc_comm_in(void *devobj, unsigned long pio, size_t dlen)
+{
+ int ret = 0;
+ unsigned char rd_data = 0;
+ unsigned long ptaddr;
+ struct lpc_cycle_para iopara;
+ struct hisilpc_dev *lpcdev = devobj;
+
+ if (!lpcdev || !dlen || dlen > LPC_MAX_DULEN)
+ return -1;
+
+ ptaddr = hisi_lpc_pio_to_addr(lpcdev, pio);
+
+ iopara.opflags = FG_INCRADDR_LPC;
+ iopara.csize = dlen;
+
+ ret = hisilpc_target_in(lpcdev, &iopara, ptaddr, &rd_data, dlen);
+ if (ret)
+ return -1;
+
+ return le32_to_cpu((u32)rd_data);
+}
+
+/**
+ * hisilpc_comm_out - output the data whose maximum length is four bytes
+ to the I/O peripheral through the LPC host.
+ * @devobj: pointer to the device information relevant to LPC controller.
+ * @pio: the target I/O port address.
+ * @outval: a value to be outputted from caller, maximum is four bytes.
+ * @dlen: the data length required writing to the target I/O port.
+ *
+ * This function is corresponding to out(b,w,l) only
+ *
+ */
+static void hisilpc_comm_out(void *devobj, unsigned long pio,
+ u32 outval, size_t dlen)
+{
+ unsigned long ptaddr;
+ struct hisilpc_dev *lpcdev = devobj;
+ struct lpc_cycle_para iopara;
+ const unsigned char *newbuf;
+
+ if (!lpcdev || !dlen || dlen > LPC_MAX_DULEN)
+ return;
+
+ outval = cpu_to_le32(outval);
+
+ newbuf = (const unsigned char *)&outval;
+ ptaddr = hisi_lpc_pio_to_addr(lpcdev, pio);
+
+ iopara.opflags = FG_INCRADDR_LPC;
+ iopara.csize = dlen;
+
+ hisilpc_target_out(lpcdev, &iopara, ptaddr, newbuf, dlen);
+}
+
+/*
+ * hisilpc_comm_ins - read/input the data in buffer to the I/O
+ * peripheral through LPC, it corresponds to ins(b,w,l)
+ * @devobj: pointer to the device information relevant to LPC controller.
+ * @pio: the target I/O port address.
+ * @inbuf: a buffer where read/input data bytes are stored.
+ * @dlen: the data length required writing to the target I/O port.
+ * @count: how many data units whose length is dlen will be read.
+ *
+ * when succeed, the data read back is stored in buffer pointed by inbuf.
+ * Returns 0 on success, -errno otherwise
+ *
+ */
+static u32
+hisilpc_comm_ins(void *devobj, unsigned long pio, void *inbuf,
+ size_t dlen, unsigned int count)
+{
+ struct hisilpc_dev *lpcdev = devobj;
+ struct lpc_cycle_para iopara;
+ unsigned char *newbuf;
+ unsigned int loopcnt, cntleft;
+ unsigned long ptaddr;
+
+ if (!lpcdev || !inbuf || !count || !dlen || dlen > LPC_MAX_DULEN ||
+ count % dlen)
+ return -EINVAL;
+
+ iopara.opflags = 0;
+ if (dlen > 1)
+ iopara.opflags |= FG_INCRADDR_LPC;
+ iopara.csize = dlen;
+
+ ptaddr = hisi_lpc_pio_to_addr(lpcdev, pio);
+ newbuf = inbuf;
+ /*
+ * ensure data stream whose length is multiple of dlen to be processed
+ * each IO input
+ */
+ cntleft = count * dlen;
+ do {
+ int ret;
+
+ loopcnt = min_t(unsigned int, LPC_MAX_BURST, cntleft);
+ ret = hisilpc_target_in(lpcdev, &iopara, ptaddr,
+ newbuf, loopcnt);
+ if (ret)
+ return ret;
+ newbuf += loopcnt;
+ cntleft -= loopcnt;
+ } while (cntleft);
+
+ return 0;
+}
+
+/*
+ * hisilpc_comm_outs - write/output the data in buffer to the I/O
+ * peripheral through LPC, it corresponds to outs(b,w,l)
+ * @devobj: pointer to the device information relevant to LPC controller.
+ * @pio: the target I/O port address.
+ * @outbuf: a buffer where write/output data bytes are stored.
+ * @dlen: the data length required writing to the target I/O port .
+ * @count: how many data units whose length is dlen will be written.
+ *
+ */
+static void
+hisilpc_comm_outs(void *devobj, unsigned long pio, const void *outbuf,
+ size_t dlen, unsigned int count)
+{
+ struct hisilpc_dev *lpcdev = devobj;
+ struct lpc_cycle_para iopara;
+ const unsigned char *newbuf;
+ unsigned int loopcnt, cntleft;
+ unsigned long ptaddr;
+
+ if (!lpcdev || !outbuf || !count || !dlen || dlen > LPC_MAX_DULEN ||
+ count % dlen)
+ return;
+
+ iopara.opflags = 0;
+ if (dlen > 1)
+ iopara.opflags |= FG_INCRADDR_LPC;
+ iopara.csize = dlen;
+
+ ptaddr = hisi_lpc_pio_to_addr(lpcdev, pio);
+ newbuf = outbuf;
+ /*
+ * ensure data stream whose length is multiple of dlen to be processed
+ * each IO input
+ */
+ cntleft = count * dlen;
+ do {
+ loopcnt = min_t(unsigned int, LPC_MAX_BURST, cntleft);
+ if (hisilpc_target_out(lpcdev, &iopara, ptaddr, newbuf,
+ loopcnt))
+ break;
+ newbuf += loopcnt;
+ cntleft -= loopcnt;
+ } while (cntleft);
+}
+
+static struct hostio_ops hisi_lpc_ops = {
+ .pfin = hisilpc_comm_in,
+ .pfout = hisilpc_comm_out,
+ .pfins = hisilpc_comm_ins,
+ .pfouts = hisilpc_comm_outs,
+};
+
+/**
+ * hisilpc_probe - the probe callback function for hisi lpc device,
+ * will finish all the initialization.
+ * @pdev: the platform device corresponding to hisi lpc
+ *
+ * Returns 0 on success, non-zero on fail.
+ */
+static int hisilpc_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct resource *res;
+ struct hisilpc_dev *lpcdev;
+ int ret = 0;
+
+ lpcdev = devm_kzalloc(dev, sizeof(struct hisilpc_dev), GFP_KERNEL);
+ if (!lpcdev)
+ return -ENOMEM;
+
+ spin_lock_init(&lpcdev->cycle_lock);
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!res)
+ return -ENODEV;
+
+ lpcdev->membase = devm_ioremap_resource(dev, res);
+ if (IS_ERR(lpcdev->membase)) {
+ dev_err(dev, "remap failed\n");
+ return PTR_ERR(lpcdev->membase);
+ }
+
+ /* register the LPC host PIO resources */
+ {
+ struct logic_pio_hwaddr *range;
+
+ range = devm_kzalloc(dev, sizeof(*range), GFP_KERNEL);
+ if (!range)
+ return -ENOMEM;
+ range->fwnode = dev->fwnode;
+ range->flags = PIO_INDIRECT;
+ range->size = PIO_INDIRECT_SIZE;
+
+ ret = logic_pio_register_range(range);
+ if (ret) {
+ kfree(range);
+ dev_err(dev, "register IO range failed (%d)!\n", ret);
+ return -ret;
+ }
+ lpcdev->io_host = range;
+
+ /*
+ * It is time to start the children scanning:
+ * For ACPI children, the corresponding devices had been
+ * created during the ACPI enumeration.
+ * The OF scanning must be performed after initialization of
+ * 'lpcdev' to avoid some children which complete the scanning
+ * trigger the MMIO accesses which will probably cause a panic.
+ */
+ ret = of_platform_populate(dev->of_node, NULL, NULL, dev);
+ if (ret) {
+ /*
+ * When LPC probing is not completely successful, set
+ * 'devpara' as NULL. This will make all the LPC I/O
+ * return failure directly without any hardware
+ * operations. It will prevent some peripherals which
+ * had not finished the initialization to manipulate
+ * I/O for safety.
+ */
+ lpcdev->io_host->devpara = NULL;
+ dev_err(dev, "populate children failed(%d)\n", ret);
+ return ret;
+ }
+ }
+ lpcdev->io_host->devpara = lpcdev;
+ lpcdev->io_host->ops = &hisi_lpc_ops;
+
+ dev_info(dev, "registered range[%pa - sz:%pa]\n",
+ &lpcdev->io_host->io_start,
+ &lpcdev->io_host->size);
+
+ return ret;
+}
+
+static const struct of_device_id hisilpc_of_match[] = {
+ { .compatible = "hisilicon,hip06-lpc", },
+ { .compatible = "hisilicon,hip07-lpc", },
+ {},
+};
+
+static struct platform_driver hisilpc_driver = {
+ .driver = {
+ .name = "hisi_lpc",
+ .of_match_table = hisilpc_of_match,
+ },
+ .probe = hisilpc_probe,
+};
+
+builtin_platform_driver(hisilpc_driver);