| Message ID | 20210517055356.1918418-1-srinivas.pandruvada@linux.intel.com (mailing list archive) |
|---|---|
| State | Superseded, archived |
| Headers | show |
| Series | ACPI: DPTF: Add new PCH FIVR methods | expand |
On Mon, May 17, 2021 at 7:54 AM Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> wrote: > > Some additional information is required for updating PCH FIVR values > upon WiFi channel changes. > > New attributes added to the existing sysfs: > fivr_switching_freq_mhz : Get the FIVR switching control frequency. > Uses ACPI method GFCS > fivr_switching_fault_status: Read the FIVR switching frequency control > fault status. Uses ACPI method GFFS > > ssc_clock_info : Presents SSC (spread spectrum clock) information for EMI > (Electro magnetic interference) control. Use ACPI method GEMI. Refer > to the description of GEMI method below. > > GFFS > This ACPI method is used to read the FIVR switching frequency control > fault status. > Bits Description > [0:0] Fault status when set to 1 > [31:1] Reserved > > GFCS > This ACPI method is used to read the FIVR switching control > frequency. > Bits Description > [11:0] Actual Frequency = value * XTAL_FREQ / 128 I was about to apply this, but one question. AFAICS the "show" function will simply evaluate GFCS and preset the returned value to the reader of the attribute, but the documentation says that this is the switching control frequency in MHz which doesn't seem to be consistent with the above information. Is the reader of the attribute required to know the XTAL frequency and apply the above formula to the value read from it? If so, the documentation should be clear about this. > [31:12] Reserved > > GEMI > This ACPI method is used to read the programmed register value for EMI > (Electro magnetic interference) control. > > Bits Description > [7:0] Sets clock spectrum spread percentage: > 0x00=0.2% , 0x3F=10% > 1 LSB = 0.1% increase in spread (for > settings 0x01 thru 0x1C) > 1 LSB = 0.2% increase in spread (for > settings 0x1E thru 0x3F) > [8] When set to 1, enables spread > spectrum clock > [9] 0: Triangle mode. FFC frequency > walks around the Fcenter in a linear > fashion > 1: Random walk mode. FFC frequency > changes randomly within the SSC > (Spread spectrum clock) range > [10] 0: No white noise. 1: Add white noise > to spread waveform > [11] When 1, future writes are ignored. > > Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> > --- > Documentation/ABI/testing/sysfs-platform-dptf | 40 +++++++++++++++++++ > drivers/acpi/dptf/dptf_pch_fivr.c | 9 +++++ > 2 files changed, 49 insertions(+) > > diff --git a/Documentation/ABI/testing/sysfs-platform-dptf b/Documentation/ABI/testing/sysfs-platform-dptf > index 141834342a4d..f0c43711ad4f 100644 > --- a/Documentation/ABI/testing/sysfs-platform-dptf > +++ b/Documentation/ABI/testing/sysfs-platform-dptf > @@ -111,3 +111,43 @@ Contact: linux-acpi@vger.kernel.org > Description: > (RW) The PCH FIVR (Fully Integrated Voltage Regulator) switching frequency in MHz, > when FIVR clock is 38.4MHz. > + > +What: /sys/bus/platform/devices/INTC1045:00/pch_fivr_switch_frequency/fivr_switching_freq_mhz > +Date: June, 2021 > +KernelVersion: v5.14 > +Contact: linux-acpi@vger.kernel.org > +Description: > + (RO) Get the FIVR switching control frequency in MHz. > + > +What: /sys/bus/platform/devices/INTC1045:00/pch_fivr_switch_frequency/fivr_switching_fault_status > +Date: June, 2021 > +KernelVersion: v5.14 > +Contact: linux-acpi@vger.kernel.org > +Description: > + (RO) Read the FIVR switching frequency control fault status. > + > +What: /sys/bus/platform/devices/INTC1045:00/pch_fivr_switch_frequency/ssc_clock_info > +Date: June, 2021 > +KernelVersion: v5.14 > +Contact: linux-acpi@vger.kernel.org > +Description: > + (RO) Presents SSC (spread spectrum clock) information for EMI > + (Electro magnetic interference) control. This is a bit mask. > + Bits Description > + [7:0] Sets clock spectrum spread percentage: > + 0x00=0.2% , 0x3F=10% > + 1 LSB = 0.1% increase in spread (for > + settings 0x01 thru 0x1C) > + 1 LSB = 0.2% increase in spread (for > + settings 0x1E thru 0x3F) > + [8] When set to 1, enables spread > + spectrum clock > + [9] 0: Triangle mode. FFC frequency > + walks around the Fcenter in a linear > + fashion > + 1: Random walk mode. FFC frequency > + changes randomly within the SSC > + (Spread spectrum clock) range > + [10] 0: No white noise. 1: Add white noise > + to spread waveform > + [11] When 1, future writes are ignored. > diff --git a/drivers/acpi/dptf/dptf_pch_fivr.c b/drivers/acpi/dptf/dptf_pch_fivr.c > index 5fca18296bf6..22c4ae0401ef 100644 > --- a/drivers/acpi/dptf/dptf_pch_fivr.c > +++ b/drivers/acpi/dptf/dptf_pch_fivr.c > @@ -55,15 +55,24 @@ static ssize_t name##_store(struct device *dev,\ > > PCH_FIVR_SHOW(freq_mhz_low_clock, GFC0) > PCH_FIVR_SHOW(freq_mhz_high_clock, GFC1) > +PCH_FIVR_SHOW(ssc_clock_info, GEMI) > +PCH_FIVR_SHOW(fivr_switching_freq_mhz, GFCS) > +PCH_FIVR_SHOW(fivr_switching_fault_status, GFFS) > PCH_FIVR_STORE(freq_mhz_low_clock, RFC0) > PCH_FIVR_STORE(freq_mhz_high_clock, RFC1) > > static DEVICE_ATTR_RW(freq_mhz_low_clock); > static DEVICE_ATTR_RW(freq_mhz_high_clock); > +static DEVICE_ATTR_RO(ssc_clock_info); > +static DEVICE_ATTR_RO(fivr_switching_freq_mhz); > +static DEVICE_ATTR_RO(fivr_switching_fault_status); > > static struct attribute *fivr_attrs[] = { > &dev_attr_freq_mhz_low_clock.attr, > &dev_attr_freq_mhz_high_clock.attr, > + &dev_attr_ssc_clock_info.attr, > + &dev_attr_fivr_switching_freq_mhz.attr, > + &dev_attr_fivr_switching_fault_status.attr, > NULL > }; > > -- > 2.27.0 >
On Mon, 2021-05-17 at 17:20 +0200, Rafael J. Wysocki wrote: > On Mon, May 17, 2021 at 7:54 AM Srinivas Pandruvada > <srinivas.pandruvada@linux.intel.com> wrote: > > > > Some additional information is required for updating PCH FIVR > > values > > upon WiFi channel changes. > > > > New attributes added to the existing sysfs: > > fivr_switching_freq_mhz : Get the FIVR switching control frequency. > > Uses ACPI method GFCS > > fivr_switching_fault_status: Read the FIVR switching frequency > > control > > fault status. Uses ACPI method GFFS > > > > ssc_clock_info : Presents SSC (spread spectrum clock) information > > for EMI > > (Electro magnetic interference) control. Use ACPI method GEMI. > > Refer > > to the description of GEMI method below. > > > > GFFS > > This ACPI method is used to read the FIVR switching frequency > > control > > fault status. > > Bits Description > > [0:0] Fault status when set to 1 > > [31:1] Reserved > > > > GFCS > > This ACPI method is used to read the FIVR switching control > > frequency. > > Bits Description > > [11:0] Actual Frequency = value * XTAL_FREQ / 128 > > I was about to apply this, but one question. > > AFAICS the "show" function will simply evaluate GFCS and preset the > returned value to the reader of the attribute, but the documentation > says that this is the switching control frequency in MHz which > doesn't > seem to be consistent with the above information. > > Is the reader of the attribute required to know the XTAL frequency > and > apply the above formula to the value read from it? If so, the > documentation should be clear about this. > Since XTAL_FREQ can be different on designs, user of the interface is supposed to know that. I will update the documentation and resend. Thanks, Srinivas > > [31:12] Reserved > > > > GEMI > > This ACPI method is used to read the programmed register value for > > EMI > > (Electro magnetic interference) control. > > > > Bits Description > > [7:0] Sets clock spectrum spread percentage: > > 0x00=0.2% , 0x3F=10% > > 1 LSB = 0.1% increase in spread (for > > settings 0x01 thru 0x1C) > > 1 LSB = 0.2% increase in spread (for > > settings 0x1E thru 0x3F) > > [8] When set to 1, enables spread > > spectrum clock > > [9] 0: Triangle mode. FFC frequency > > walks around the Fcenter in a linear > > fashion > > 1: Random walk mode. FFC frequency > > changes randomly within the SSC > > (Spread spectrum clock) range > > [10] 0: No white noise. 1: Add white noise > > to spread waveform > > [11] When 1, future writes are ignored. > > > > Signed-off-by: Srinivas Pandruvada < > > srinivas.pandruvada@linux.intel.com> > > --- > > Documentation/ABI/testing/sysfs-platform-dptf | 40 > > +++++++++++++++++++ > > drivers/acpi/dptf/dptf_pch_fivr.c | 9 +++++ > > 2 files changed, 49 insertions(+) > > > > diff --git a/Documentation/ABI/testing/sysfs-platform-dptf > > b/Documentation/ABI/testing/sysfs-platform-dptf > > index 141834342a4d..f0c43711ad4f 100644 > > --- a/Documentation/ABI/testing/sysfs-platform-dptf > > +++ b/Documentation/ABI/testing/sysfs-platform-dptf > > @@ -111,3 +111,43 @@ Contact: linux-acpi@vger.kernel.org > > Description: > > (RW) The PCH FIVR (Fully Integrated Voltage > > Regulator) switching frequency in MHz, > > when FIVR clock is 38.4MHz. > > + > > +What: > > /sys/bus/platform/devices/INTC1045:00/pch_fivr_switch_frequency/fiv > > r_switching_freq_mhz > > +Date: June, 2021 > > +KernelVersion: v5.14 > > +Contact: linux-acpi@vger.kernel.org > > +Description: > > + (RO) Get the FIVR switching control frequency in > > MHz. > > + > > +What: > > /sys/bus/platform/devices/INTC1045:00/pch_fivr_switch_frequency/fiv > > r_switching_fault_status > > +Date: June, 2021 > > +KernelVersion: v5.14 > > +Contact: linux-acpi@vger.kernel.org > > +Description: > > + (RO) Read the FIVR switching frequency control > > fault status. > > + > > +What: > > /sys/bus/platform/devices/INTC1045:00/pch_fivr_switch_frequency/ssc > > _clock_info > > +Date: June, 2021 > > +KernelVersion: v5.14 > > +Contact: linux-acpi@vger.kernel.org > > +Description: > > + (RO) Presents SSC (spread spectrum clock) > > information for EMI > > + (Electro magnetic interference) control. This is a > > bit mask. > > + Bits Description > > + [7:0] Sets clock spectrum spread percentage: > > + 0x00=0.2% , 0x3F=10% > > + 1 LSB = 0.1% increase in spread (for > > + settings 0x01 thru 0x1C) > > + 1 LSB = 0.2% increase in spread (for > > + settings 0x1E thru 0x3F) > > + [8] When set to 1, enables spread > > + spectrum clock > > + [9] 0: Triangle mode. FFC frequency > > + walks around the Fcenter in a linear > > + fashion > > + 1: Random walk mode. FFC frequency > > + changes randomly within the SSC > > + (Spread spectrum clock) range > > + [10] 0: No white noise. 1: Add white noise > > + to spread waveform > > + [11] When 1, future writes are ignored. > > diff --git a/drivers/acpi/dptf/dptf_pch_fivr.c > > b/drivers/acpi/dptf/dptf_pch_fivr.c > > index 5fca18296bf6..22c4ae0401ef 100644 > > --- a/drivers/acpi/dptf/dptf_pch_fivr.c > > +++ b/drivers/acpi/dptf/dptf_pch_fivr.c > > @@ -55,15 +55,24 @@ static ssize_t name##_store(struct device > > *dev,\ > > > > PCH_FIVR_SHOW(freq_mhz_low_clock, GFC0) > > PCH_FIVR_SHOW(freq_mhz_high_clock, GFC1) > > +PCH_FIVR_SHOW(ssc_clock_info, GEMI) > > +PCH_FIVR_SHOW(fivr_switching_freq_mhz, GFCS) > > +PCH_FIVR_SHOW(fivr_switching_fault_status, GFFS) > > PCH_FIVR_STORE(freq_mhz_low_clock, RFC0) > > PCH_FIVR_STORE(freq_mhz_high_clock, RFC1) > > > > static DEVICE_ATTR_RW(freq_mhz_low_clock); > > static DEVICE_ATTR_RW(freq_mhz_high_clock); > > +static DEVICE_ATTR_RO(ssc_clock_info); > > +static DEVICE_ATTR_RO(fivr_switching_freq_mhz); > > +static DEVICE_ATTR_RO(fivr_switching_fault_status); > > > > static struct attribute *fivr_attrs[] = { > > &dev_attr_freq_mhz_low_clock.attr, > > &dev_attr_freq_mhz_high_clock.attr, > > + &dev_attr_ssc_clock_info.attr, > > + &dev_attr_fivr_switching_freq_mhz.attr, > > + &dev_attr_fivr_switching_fault_status.attr, > > NULL > > }; > > > > -- > > 2.27.0 > >
diff --git a/Documentation/ABI/testing/sysfs-platform-dptf b/Documentation/ABI/testing/sysfs-platform-dptf index 141834342a4d..f0c43711ad4f 100644 --- a/Documentation/ABI/testing/sysfs-platform-dptf +++ b/Documentation/ABI/testing/sysfs-platform-dptf @@ -111,3 +111,43 @@ Contact: linux-acpi@vger.kernel.org Description: (RW) The PCH FIVR (Fully Integrated Voltage Regulator) switching frequency in MHz, when FIVR clock is 38.4MHz. + +What: /sys/bus/platform/devices/INTC1045:00/pch_fivr_switch_frequency/fivr_switching_freq_mhz +Date: June, 2021 +KernelVersion: v5.14 +Contact: linux-acpi@vger.kernel.org +Description: + (RO) Get the FIVR switching control frequency in MHz. + +What: /sys/bus/platform/devices/INTC1045:00/pch_fivr_switch_frequency/fivr_switching_fault_status +Date: June, 2021 +KernelVersion: v5.14 +Contact: linux-acpi@vger.kernel.org +Description: + (RO) Read the FIVR switching frequency control fault status. + +What: /sys/bus/platform/devices/INTC1045:00/pch_fivr_switch_frequency/ssc_clock_info +Date: June, 2021 +KernelVersion: v5.14 +Contact: linux-acpi@vger.kernel.org +Description: + (RO) Presents SSC (spread spectrum clock) information for EMI + (Electro magnetic interference) control. This is a bit mask. + Bits Description + [7:0] Sets clock spectrum spread percentage: + 0x00=0.2% , 0x3F=10% + 1 LSB = 0.1% increase in spread (for + settings 0x01 thru 0x1C) + 1 LSB = 0.2% increase in spread (for + settings 0x1E thru 0x3F) + [8] When set to 1, enables spread + spectrum clock + [9] 0: Triangle mode. FFC frequency + walks around the Fcenter in a linear + fashion + 1: Random walk mode. FFC frequency + changes randomly within the SSC + (Spread spectrum clock) range + [10] 0: No white noise. 1: Add white noise + to spread waveform + [11] When 1, future writes are ignored. diff --git a/drivers/acpi/dptf/dptf_pch_fivr.c b/drivers/acpi/dptf/dptf_pch_fivr.c index 5fca18296bf6..22c4ae0401ef 100644 --- a/drivers/acpi/dptf/dptf_pch_fivr.c +++ b/drivers/acpi/dptf/dptf_pch_fivr.c @@ -55,15 +55,24 @@ static ssize_t name##_store(struct device *dev,\ PCH_FIVR_SHOW(freq_mhz_low_clock, GFC0) PCH_FIVR_SHOW(freq_mhz_high_clock, GFC1) +PCH_FIVR_SHOW(ssc_clock_info, GEMI) +PCH_FIVR_SHOW(fivr_switching_freq_mhz, GFCS) +PCH_FIVR_SHOW(fivr_switching_fault_status, GFFS) PCH_FIVR_STORE(freq_mhz_low_clock, RFC0) PCH_FIVR_STORE(freq_mhz_high_clock, RFC1) static DEVICE_ATTR_RW(freq_mhz_low_clock); static DEVICE_ATTR_RW(freq_mhz_high_clock); +static DEVICE_ATTR_RO(ssc_clock_info); +static DEVICE_ATTR_RO(fivr_switching_freq_mhz); +static DEVICE_ATTR_RO(fivr_switching_fault_status); static struct attribute *fivr_attrs[] = { &dev_attr_freq_mhz_low_clock.attr, &dev_attr_freq_mhz_high_clock.attr, + &dev_attr_ssc_clock_info.attr, + &dev_attr_fivr_switching_freq_mhz.attr, + &dev_attr_fivr_switching_fault_status.attr, NULL };
Some additional information is required for updating PCH FIVR values upon WiFi channel changes. New attributes added to the existing sysfs: fivr_switching_freq_mhz : Get the FIVR switching control frequency. Uses ACPI method GFCS fivr_switching_fault_status: Read the FIVR switching frequency control fault status. Uses ACPI method GFFS ssc_clock_info : Presents SSC (spread spectrum clock) information for EMI (Electro magnetic interference) control. Use ACPI method GEMI. Refer to the description of GEMI method below. GFFS This ACPI method is used to read the FIVR switching frequency control fault status. Bits Description [0:0] Fault status when set to 1 [31:1] Reserved GFCS This ACPI method is used to read the FIVR switching control frequency. Bits Description [11:0] Actual Frequency = value * XTAL_FREQ / 128 [31:12] Reserved GEMI This ACPI method is used to read the programmed register value for EMI (Electro magnetic interference) control. Bits Description [7:0] Sets clock spectrum spread percentage: 0x00=0.2% , 0x3F=10% 1 LSB = 0.1% increase in spread (for settings 0x01 thru 0x1C) 1 LSB = 0.2% increase in spread (for settings 0x1E thru 0x3F) [8] When set to 1, enables spread spectrum clock [9] 0: Triangle mode. FFC frequency walks around the Fcenter in a linear fashion 1: Random walk mode. FFC frequency changes randomly within the SSC (Spread spectrum clock) range [10] 0: No white noise. 1: Add white noise to spread waveform [11] When 1, future writes are ignored. Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> --- Documentation/ABI/testing/sysfs-platform-dptf | 40 +++++++++++++++++++ drivers/acpi/dptf/dptf_pch_fivr.c | 9 +++++ 2 files changed, 49 insertions(+)