| Message ID | 1486110491-8921-1-git-send-email-ulf.hansson@linaro.org (mailing list archive) |
|---|---|
| State | Superseded |
| Headers | show |
Ulf Hansson <ulf.hansson@linaro.org> writes: > The current code dealing with calculating mmc->f_min is a bit complicated. > Additionally, the attempt to set an initial clock rate should explicitly > use a rate between 100KHz to 400 KHz, according the (e)MMC/SD specs, which > it doesn't. > > Fix the problem and clean up the code by using clk_round_rate() to pick the > nearest minimum rate to 100KHz. > > Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> > --- > > Note, this is compile tested only so I hope someone with the HW can give it a > go. Tested-by: Kevin Hilman <khilman@baylibre.com> Not being an MMC expert, I didn't fully understand how f_min was meant to be used by the core code, so the initial driver was simply calculating the lowest clock rate available based on the input clocks. Thanks for cleaning that up. Kevin > --- > drivers/mmc/host/meson-gx-mmc.c | 19 ++++++------------- > 1 file changed, 6 insertions(+), 13 deletions(-) > > diff --git a/drivers/mmc/host/meson-gx-mmc.c b/drivers/mmc/host/meson-gx-mmc.c > index 5eca88b..c672e01 100644 > --- a/drivers/mmc/host/meson-gx-mmc.c > +++ b/drivers/mmc/host/meson-gx-mmc.c > @@ -240,7 +240,6 @@ static int meson_mmc_clk_init(struct meson_host *host) > const char *mux_parent_names[MUX_CLK_NUM_PARENTS]; > unsigned int mux_parent_count = 0; > const char *clk_div_parents[1]; > - unsigned int f_min = UINT_MAX; > u32 clk_reg, cfg; > > /* get the mux parents */ > @@ -257,20 +256,10 @@ static int meson_mmc_clk_init(struct meson_host *host) > return ret; > } > > - host->mux_parent_rate[i] = clk_get_rate(host->mux_parent[i]); > mux_parent_names[i] = __clk_get_name(host->mux_parent[i]); > mux_parent_count++; > - if (host->mux_parent_rate[i] < f_min) > - f_min = host->mux_parent_rate[i]; > } > > - /* cacluate f_min based on input clocks, and max divider value */ > - if (f_min != UINT_MAX) > - f_min = DIV_ROUND_UP(CLK_SRC_XTAL_RATE, CLK_DIV_MAX); > - else > - f_min = 4000000; /* default min: 400 MHz */ > - host->mmc->f_min = f_min; > - > /* create the mux */ > snprintf(clk_name, sizeof(clk_name), "%s#mux", dev_name(host->dev)); > init.name = clk_name; > @@ -325,9 +314,13 @@ static int meson_mmc_clk_init(struct meson_host *host) > writel(cfg, host->regs + SD_EMMC_CFG); > > ret = clk_prepare_enable(host->cfg_div_clk); > - if (!ret) > - ret = meson_mmc_clk_set(host, f_min); > + if (ret) > + return ret; > + > + /* Get the nearest minimum clock to 100KHz */ > + host->mmc->f_min = clk_round_rate(host->cfg_div_clk, 100000); > > + ret = meson_mmc_clk_set(host, host->mmc->f_min); > if (!ret) > clk_disable_unprepare(host->cfg_div_clk);
diff --git a/drivers/mmc/host/meson-gx-mmc.c b/drivers/mmc/host/meson-gx-mmc.c index 5eca88b..c672e01 100644 --- a/drivers/mmc/host/meson-gx-mmc.c +++ b/drivers/mmc/host/meson-gx-mmc.c @@ -240,7 +240,6 @@ static int meson_mmc_clk_init(struct meson_host *host) const char *mux_parent_names[MUX_CLK_NUM_PARENTS]; unsigned int mux_parent_count = 0; const char *clk_div_parents[1]; - unsigned int f_min = UINT_MAX; u32 clk_reg, cfg; /* get the mux parents */ @@ -257,20 +256,10 @@ static int meson_mmc_clk_init(struct meson_host *host) return ret; } - host->mux_parent_rate[i] = clk_get_rate(host->mux_parent[i]); mux_parent_names[i] = __clk_get_name(host->mux_parent[i]); mux_parent_count++; - if (host->mux_parent_rate[i] < f_min) - f_min = host->mux_parent_rate[i]; } - /* cacluate f_min based on input clocks, and max divider value */ - if (f_min != UINT_MAX) - f_min = DIV_ROUND_UP(CLK_SRC_XTAL_RATE, CLK_DIV_MAX); - else - f_min = 4000000; /* default min: 400 MHz */ - host->mmc->f_min = f_min; - /* create the mux */ snprintf(clk_name, sizeof(clk_name), "%s#mux", dev_name(host->dev)); init.name = clk_name; @@ -325,9 +314,13 @@ static int meson_mmc_clk_init(struct meson_host *host) writel(cfg, host->regs + SD_EMMC_CFG); ret = clk_prepare_enable(host->cfg_div_clk); - if (!ret) - ret = meson_mmc_clk_set(host, f_min); + if (ret) + return ret; + + /* Get the nearest minimum clock to 100KHz */ + host->mmc->f_min = clk_round_rate(host->cfg_div_clk, 100000); + ret = meson_mmc_clk_set(host, host->mmc->f_min); if (!ret) clk_disable_unprepare(host->cfg_div_clk);
The current code dealing with calculating mmc->f_min is a bit complicated. Additionally, the attempt to set an initial clock rate should explicitly use a rate between 100KHz to 400 KHz, according the (e)MMC/SD specs, which it doesn't. Fix the problem and clean up the code by using clk_round_rate() to pick the nearest minimum rate to 100KHz. Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> --- Note, this is compile tested only so I hope someone with the HW can give it a go. --- drivers/mmc/host/meson-gx-mmc.c | 19 ++++++------------- 1 file changed, 6 insertions(+), 13 deletions(-)