diff mbox

[0/2] Add support for Amlogic Meson MMC controller

Message ID 20160520193443.GA17269@mephisto (mailing list archive)
State Not Applicable
Headers show

Commit Message

Carlo Caione May 20, 2016, 7:34 p.m. UTC
On 20/05/16 11:58, Robert Gadsdon wrote:
> On 05/20/2016 01:07 AM, Carlo Caione wrote:
> > On 20/05/16 08:27, Carlo Caione wrote:
> >> On 19/05/16 21:51, Robert Gadsdon wrote:
> >>> Applied this on my Odroid C2, and it worked OK when installed on the
> >>> SDcard, but failed when installed on the eMMC module:
> > 
> > Oh, reading this again you meant that you put u-boot directly on the
> > eMMC? Ok then, something is wrong when using the driver with the eMMC.
> > 
> 
> Yes, I installed it directly on the eMMC, using the micro-sd adapter,
> and following the same instructions as for the SDcard..

Could you try with this patch?


Thanks,

Comments

Robert Gadsdon May 21, 2016, 2:28 a.m. UTC | #1
On 05/20/2016 12:34 PM, Carlo Caione wrote:
> On 20/05/16 11:58, Robert Gadsdon wrote:
>> On 05/20/2016 01:07 AM, Carlo Caione wrote:
>>> On 20/05/16 08:27, Carlo Caione wrote:
>>>> On 19/05/16 21:51, Robert Gadsdon wrote:
>>>>> Applied this on my Odroid C2, and it worked OK when installed on the
>>>>> SDcard, but failed when installed on the eMMC module:
>>> Oh, reading this again you meant that you put u-boot directly on the
>>> eMMC? Ok then, something is wrong when using the driver with the eMMC.
>>>
>>> Yes, I installed it directly on the eMMC, using the micro-sd adapter,
>>> and following the same instructions as for the SDcard..
> Could you try with this patch?
>
> diff --git a/board/hardkernel/odroid-c2/odroid-c2.c
> b/board/hardkernel/odroid-c2/odroid-c2.c
> index 34b9a95..ab78328 100644
> --- a/board/hardkernel/odroid-c2/odroid-c2.c
> +++ b/board/hardkernel/odroid-c2/odroid-c2.c
> @@ -80,6 +80,11 @@ U_BOOT_DEVICE(meson_mmc) = {
>         .platdata = &gxbb_sd_platdata[CONFIG_MMC_MESON_SD_PORT],
> 	 };
> 	  
> 	  +U_BOOT_DEVICE(meson_emmc) = {
> 	  +       .name = "meson_mmc",
> 	  +       .platdata = &gxbb_sd_platdata[2],
> 	  +};
> 	  +
> 	   static void meson_mmc_pinmux_setup(unsigned int port)
> 	    {
> 	            switch (port) {
>
> Thanks,

Patch applied, and now the eMMC is detected OK:

=> mmc info
Device: <NULL>
Manufacturer ID: 15
OEM: 100
Name: BGND3
Tran Speed: 52000000
Rd Block Len: 512
MMC version 5.0
High Capacity: Yes
Capacity: 29.1 GiB
Bus Width: 8-bit
Erase Group Size: 512 KiB
HC WP Group Size: 8 MiB
User Capacity: 29.1 GiB WRREL
Boot Capacity: 4 MiB ENH
RPMB Capacity: 4 MiB ENH

...  And I can load/boot the Kernel (as far as the /dev/mmc... prompt..)

Thanks!

Robert Gadsdon.
diff mbox

Patch

diff --git a/board/hardkernel/odroid-c2/odroid-c2.c
b/board/hardkernel/odroid-c2/odroid-c2.c
index 34b9a95..ab78328 100644
--- a/board/hardkernel/odroid-c2/odroid-c2.c
+++ b/board/hardkernel/odroid-c2/odroid-c2.c
@@ -80,6 +80,11 @@  U_BOOT_DEVICE(meson_mmc) = {
        .platdata = &gxbb_sd_platdata[CONFIG_MMC_MESON_SD_PORT],
	 };
	  
	  +U_BOOT_DEVICE(meson_emmc) = {
	  +       .name = "meson_mmc",
	  +       .platdata = &gxbb_sd_platdata[2],
	  +};
	  +
	   static void meson_mmc_pinmux_setup(unsigned int port)
	    {
	            switch (port) {