@@ -24,6 +24,9 @@
#define REG_PIN_47_SEL 0x08
#define REG_FILTER_SEL 0x0c
+/* use for A1 like chips */
+#define REG_PIN_A1_SEL 0x04
+
/*
* Note: The S905X3 datasheet reports that BOTH_EDGE is controlled by
* bits 24 to 31. Tests on the actual HW show that these bits are
@@ -44,6 +47,10 @@ struct meson_gpio_irq_controller;
static void meson8_gpio_irq_sel_pin(struct meson_gpio_irq_controller *ctl,
unsigned int channel, unsigned long hwirq);
static void meson_gpio_irq_init_dummy(struct meson_gpio_irq_controller *ctl);
+static void meson_a1_gpio_irq_sel_pin(struct meson_gpio_irq_controller *ctl,
+ unsigned int channel,
+ unsigned long hwirq);
+static void meson_a1_gpio_irq_init(struct meson_gpio_irq_controller *ctl);
struct irq_ctl_ops {
void (*gpio_irq_sel_pin)(struct meson_gpio_irq_controller *ctl,
@@ -75,6 +82,15 @@ struct meson_gpio_irq_params {
.pol_low_offset = 16, \
.pin_sel_mask = 0xff, \
+#define INIT_MESON_A1_COMMON_DATA(irqs) \
+ INIT_MESON_COMMON(irqs, meson_a1_gpio_irq_init, \
+ meson_a1_gpio_irq_sel_pin) \
+ .support_edge_both = true, \
+ .edge_both_offset = 16, \
+ .edge_single_offset = 8, \
+ .pol_low_offset = 0, \
+ .pin_sel_mask = 0x7f, \
+
static const struct meson_gpio_irq_params meson8_params = {
INIT_MESON8_COMMON_DATA(134)
};
@@ -101,6 +117,10 @@ static const struct meson_gpio_irq_params sm1_params = {
.edge_both_offset = 8,
};
+static const struct meson_gpio_irq_params a1_params = {
+ INIT_MESON_A1_COMMON_DATA(62)
+};
+
static const struct of_device_id meson_irq_gpio_matches[] = {
{ .compatible = "amlogic,meson8-gpio-intc", .data = &meson8_params },
{ .compatible = "amlogic,meson8b-gpio-intc", .data = &meson8b_params },
@@ -109,6 +129,7 @@ static const struct of_device_id meson_irq_gpio_matches[] = {
{ .compatible = "amlogic,meson-axg-gpio-intc", .data = &axg_params },
{ .compatible = "amlogic,meson-g12a-gpio-intc", .data = &axg_params },
{ .compatible = "amlogic,meson-sm1-gpio-intc", .data = &sm1_params },
+ { .compatible = "amlogic,meson-a1-gpio-intc", .data = &a1_params },
{ }
};
@@ -149,6 +170,27 @@ static void meson8_gpio_irq_sel_pin(struct meson_gpio_irq_controller *ctl,
hwirq << bit_offset);
}
+static void meson_a1_gpio_irq_sel_pin(struct meson_gpio_irq_controller *ctl,
+ unsigned int channel,
+ unsigned long hwirq)
+{
+ unsigned int reg_offset;
+ unsigned int bit_offset;
+
+ bit_offset = ((channel % 2) == 0) ? 0 : 16;
+ reg_offset = REG_PIN_A1_SEL + ((channel / 2) << 2);
+
+ meson_gpio_irq_update_bits(ctl, reg_offset,
+ ctl->params->pin_sel_mask << bit_offset,
+ hwirq << bit_offset);
+}
+
+/* For a1 or later chips like a1 there is a switch to enable/disable irq */
+static void meson_a1_gpio_irq_init(struct meson_gpio_irq_controller *ctl)
+{
+ meson_gpio_irq_update_bits(ctl, REG_EDGE_POL, BIT(31), BIT(31));
+}
+
static int
meson_gpio_irq_request_channel(struct meson_gpio_irq_controller *ctl,
unsigned long hwirq,
The meson a1 Socs have some changes compared with previous chips. For A113L, it contains 62 pins and can be spied on: - 62:128 undefined - 61:50 12 pins on bank A - 49:37 13 pins on bank F - 36:20 17 pins on bank X - 19:13 7 pins on bank B - 12:0 13 pins on bank P There are five relative registers for gpio interrupt controller, details are as below: - PADCTRL_GPIO_IRQ_CTRL0 bit[31]: enable/disable the whole irq lines bit[16-23]: both edge trigger bit[8-15]: single edge trigger bit[0-7]: pol trigger - PADCTRL_GPIO_IRQ_CTRL[X] bit[0-6]: 7 bits to choose gpio source for irq line 2*[X] - 2 bit[16-22]: 7 bits to choose gpio source for irq line 2*[X] - 1 where X =1,2,3,4 Signed-off-by: Qianggui Song <qianggui.song@amlogic.com> --- drivers/irqchip/irq-meson-gpio.c | 42 ++++++++++++++++++++++++++++++++ 1 file changed, 42 insertions(+)