diff mbox series

[RFC,v2,08/11] net: stmmac: dwmac-meson8b: add support for the RX delay configuration

Message ID 20200429201644.1144546-9-martin.blumenstingl@googlemail.com (mailing list archive)
State Superseded
Headers show
Series dwmac-meson8b Ethernet RX delay configuration | expand

Commit Message

Martin Blumenstingl April 29, 2020, 8:16 p.m. UTC 
Configure the PRG_ETH0_ADJ_* bits to enable or disable the RX delay
based on the various RGMII PHY modes. For now the only supported RX
delay settings are:
- disabled, use for example for phy-mode "rgmii-id"
- 0ns - this is treated identical to "disabled", used for example on
  boards where the PHY provides 2ns TX delay and the PCB trace length
  already adds 2ns RX delay
- 2ns - for whenever the PHY cannot add the RX delay and the traces on
  the PCB don't add any RX delay

Disabling the RX delay (in case u-boot enables it, which is the case
for example on Meson8b Odroid-C1) simply means that PRG_ETH0_ADJ_ENABLE,
PRG_ETH0_ADJ_SETUP, PRG_ETH0_ADJ_DELAY and PRG_ETH0_ADJ_SKEW should be
disabled (just disabling PRG_ETH0_ADJ_ENABLE may be enough, since that
disables the whole re-timing logic - but I find it makes more sense to
clear the other bits as well since they depend on that setting).

u-boot on Odroid-C1 uses the following steps to enable a 2ns RX delay:
- enabling enabling the timing adjustment clock
- enabling the timing adjustment logic by setting PRG_ETH0_ADJ_ENABLE
- setting the PRG_ETH0_ADJ_SETUP bit

The documentation for the PRG_ETH0_ADJ_DELAY and PRG_ETH0_ADJ_SKEW
registers indicates that we can even set different RX delays. However,
I could not find out how this works exactly, so for now we only support
a 2ns RX delay using the exact same way that Odroid-C1's u-boot does.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
---
 .../ethernet/stmicro/stmmac/dwmac-meson8b.c   | 79 +++++++++++++------
 1 file changed, 56 insertions(+), 23 deletions(-)

Comments

Andrew Lunn May 1, 2020, 3:44 p.m. UTC | #1 
> +	if (rx_dly_config & PRG_ETH0_ADJ_ENABLE) {
> +		/* The timing adjustment logic is driven by a separate clock */
> +		ret = meson8b_devm_clk_prepare_enable(dwmac,
> +						      dwmac->timing_adj_clk);
> +		if (ret) {
> +			dev_err(dwmac->dev,
> +				"Failed to enable the timing-adjustment clock\n");
> +			return ret;
> +		}
> +	}

Hi Martin

It is a while since i used the clk API. I thought the get_optional()
call returned a NULL pointer if the clock does not exist.
clk_prepare_enable() passed a NULL pointer is a NOP, but it also does
not return an error. So if the clock does not exist, you won't get
this error, the code keeps going, configures the hardware, but it does
not work.

I think you need to check dwmac->timing_adj_clk != NULL here, and
error out if DT has properties which require it.

      Andrew
Martin Blumenstingl May 1, 2020, 5:10 p.m. UTC | #2 
Hi Andrew,

On Fri, May 1, 2020 at 5:44 PM Andrew Lunn <andrew@lunn.ch> wrote:
>
> > +     if (rx_dly_config & PRG_ETH0_ADJ_ENABLE) {
> > +             /* The timing adjustment logic is driven by a separate clock */
> > +             ret = meson8b_devm_clk_prepare_enable(dwmac,
> > +                                                   dwmac->timing_adj_clk);
> > +             if (ret) {
> > +                     dev_err(dwmac->dev,
> > +                             "Failed to enable the timing-adjustment clock\n");
> > +                     return ret;
> > +             }
> > +     }
>
> Hi Martin
>
> It is a while since i used the clk API. I thought the get_optional()
> call returned a NULL pointer if the clock does not exist.
> clk_prepare_enable() passed a NULL pointer is a NOP, but it also does
> not return an error. So if the clock does not exist, you won't get
> this error, the code keeps going, configures the hardware, but it does
> not work.
>
> I think you need to check dwmac->timing_adj_clk != NULL here, and
> error out if DT has properties which require it.
Thank you for your excellent code review quality (as always)!
you are right and I will fix that in the next version


Martin
diff mbox series

Patch

diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-meson8b.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-meson8b.c
index d31f79c455de..73c84108d65b 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-meson8b.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-meson8b.c
@@ -85,6 +85,7 @@  struct meson8b_dwmac {
 	phy_interface_t			phy_mode;
 	struct clk			*rgmii_tx_clk;
 	u32				tx_delay_ns;
+	u32				rx_delay_ns;
 	struct clk			*timing_adj_clk;
 };
 
@@ -284,25 +285,58 @@  static int meson8b_devm_clk_prepare_enable(struct meson8b_dwmac *dwmac,
 
 static int meson8b_init_prg_eth(struct meson8b_dwmac *dwmac)
 {
+	u32 tx_dly_config, rx_dly_config, delay_config;
 	int ret;
-	u8 tx_dly_val = 0;
+
+	tx_dly_config = FIELD_PREP(PRG_ETH0_TXDLY_MASK,
+				   dwmac->tx_delay_ns >> 1);
+
+	if (dwmac->rx_delay_ns == 2)
+		rx_dly_config = PRG_ETH0_ADJ_ENABLE | PRG_ETH0_ADJ_SETUP;
+	else
+		rx_dly_config = 0;
 
 	switch (dwmac->phy_mode) {
 	case PHY_INTERFACE_MODE_RGMII:
+		delay_config = tx_dly_config | rx_dly_config;
+		break;
 	case PHY_INTERFACE_MODE_RGMII_RXID:
-		tx_dly_val = dwmac->tx_delay_ns >> 1;
-		/* fall through */
-
-	case PHY_INTERFACE_MODE_RGMII_ID:
+		delay_config = tx_dly_config;
+		break;
 	case PHY_INTERFACE_MODE_RGMII_TXID:
+		delay_config = rx_dly_config;
+		break;
+	case PHY_INTERFACE_MODE_RGMII_ID:
+	case PHY_INTERFACE_MODE_RMII:
+		delay_config = 0;
+		break;
+	default:
+		dev_err(dwmac->dev, "unsupported phy-mode %s\n",
+			phy_modes(dwmac->phy_mode));
+		return -EINVAL;
+	};
+
+	if (rx_dly_config & PRG_ETH0_ADJ_ENABLE) {
+		/* The timing adjustment logic is driven by a separate clock */
+		ret = meson8b_devm_clk_prepare_enable(dwmac,
+						      dwmac->timing_adj_clk);
+		if (ret) {
+			dev_err(dwmac->dev,
+				"Failed to enable the timing-adjustment clock\n");
+			return ret;
+		}
+	}
+
+	meson8b_dwmac_mask_bits(dwmac, PRG_ETH0, PRG_ETH0_TXDLY_MASK |
+				PRG_ETH0_ADJ_ENABLE | PRG_ETH0_ADJ_SETUP |
+				PRG_ETH0_ADJ_DELAY | PRG_ETH0_ADJ_SKEW,
+				delay_config);
+
+	if (phy_interface_mode_is_rgmii(dwmac->phy_mode)) {
 		/* only relevant for RMII mode -> disable in RGMII mode */
 		meson8b_dwmac_mask_bits(dwmac, PRG_ETH0,
 					PRG_ETH0_INVERTED_RMII_CLK, 0);
 
-		meson8b_dwmac_mask_bits(dwmac, PRG_ETH0, PRG_ETH0_TXDLY_MASK,
-					FIELD_PREP(PRG_ETH0_TXDLY_MASK,
-						   tx_dly_val));
-
 		/* Configure the 125MHz RGMII TX clock, the IP block changes
 		 * the output automatically (= without us having to configure
 		 * a register) based on the line-speed (125MHz for Gbit speeds,
@@ -322,24 +356,11 @@  static int meson8b_init_prg_eth(struct meson8b_dwmac *dwmac)
 				"failed to enable the RGMII TX clock\n");
 			return ret;
 		}
-		break;
-
-	case PHY_INTERFACE_MODE_RMII:
+	} else {
 		/* invert internal clk_rmii_i to generate 25/2.5 tx_rx_clk */
 		meson8b_dwmac_mask_bits(dwmac, PRG_ETH0,
 					PRG_ETH0_INVERTED_RMII_CLK,
 					PRG_ETH0_INVERTED_RMII_CLK);
-
-		/* TX clock delay cannot be configured in RMII mode */
-		meson8b_dwmac_mask_bits(dwmac, PRG_ETH0, PRG_ETH0_TXDLY_MASK,
-					0);
-
-		break;
-
-	default:
-		dev_err(dwmac->dev, "unsupported phy-mode %s\n",
-			phy_modes(dwmac->phy_mode));
-		return -EINVAL;
 	}
 
 	/* enable TX_CLK and PHY_REF_CLK generator */
@@ -394,6 +415,18 @@  static int meson8b_dwmac_probe(struct platform_device *pdev)
 				 &dwmac->tx_delay_ns))
 		dwmac->tx_delay_ns = 2;
 
+	/* use 0ns as fallback since this is what most boards actually use */
+	if (of_property_read_u32(pdev->dev.of_node, "amlogic,rx-delay-ns",
+				 &dwmac->rx_delay_ns))
+		dwmac->rx_delay_ns = 0;
+
+	if (dwmac->rx_delay_ns != 0 && dwmac->rx_delay_ns != 2) {
+		dev_err(&pdev->dev,
+			"The only allowed RX delays values are: 0ns, 2ns");
+		ret = -EINVAL;
+		goto err_remove_config_dt;
+	}
+
 	dwmac->timing_adj_clk = devm_clk_get_optional(dwmac->dev,
 						      "timing-adjustment");
 	if (IS_ERR(dwmac->timing_adj_clk)) {