@@ -750,7 +750,7 @@ static int dwc3_meson_g12a_probe(struct platform_device *pdev)
ret = dwc3_meson_g12a_get_phys(priv);
if (ret)
- goto err_disable_clks;
+ goto err_rearm;
ret = priv->drvdata->setup_regmaps(priv, base);
if (ret)
@@ -759,7 +759,7 @@ static int dwc3_meson_g12a_probe(struct platform_device *pdev)
if (priv->vbus) {
ret = regulator_enable(priv->vbus);
if (ret)
- goto err_disable_clks;
+ goto err_rearm;
}
/* Get dr_mode */
@@ -772,13 +772,13 @@ static int dwc3_meson_g12a_probe(struct platform_device *pdev)
ret = priv->drvdata->usb_init(priv);
if (ret)
- goto err_disable_clks;
+ goto err_rearm;
/* Init PHYs */
for (i = 0 ; i < PHY_COUNT ; ++i) {
ret = phy_init(priv->phys[i]);
if (ret)
- goto err_disable_clks;
+ goto err_rearm;
}
/* Set PHY Power */
@@ -816,6 +816,9 @@ static int dwc3_meson_g12a_probe(struct platform_device *pdev)
for (i = 0 ; i < PHY_COUNT ; ++i)
phy_exit(priv->phys[i]);
+err_rearm:
+ reset_control_rearm(priv->reset);
+
err_disable_clks:
clk_bulk_disable_unprepare(priv->drvdata->num_clks,
priv->drvdata->clks);
@@ -843,6 +846,8 @@ static int dwc3_meson_g12a_remove(struct platform_device *pdev)
pm_runtime_put_noidle(dev);
pm_runtime_set_suspended(dev);
+ reset_control_rearm(priv->reset);
+
clk_bulk_disable_unprepare(priv->drvdata->num_clks,
priv->drvdata->clks);
@@ -883,7 +888,7 @@ static int __maybe_unused dwc3_meson_g12a_suspend(struct device *dev)
phy_exit(priv->phys[i]);
}
- reset_control_assert(priv->reset);
+ reset_control_rearm(priv->reset);
return 0;
}
@@ -893,7 +898,9 @@ static int __maybe_unused dwc3_meson_g12a_resume(struct device *dev)
struct dwc3_meson_g12a *priv = dev_get_drvdata(dev);
int i, ret;
- reset_control_deassert(priv->reset);
+ ret = reset_control_reset(priv->reset);
+ if (ret)
+ return ret;
ret = priv->drvdata->usb_init(priv);
if (ret)
reset_control_(de)assert() calls are called on a shared reset line when reset_control_reset has been used. This is not allowed by the reset framework. Use reset_control_rearm() call in suspend() and remove() as a way to state that the resource is no longer used, hence the shared reset line may be triggered again by other devices. Use reset_control_rearm() also in case probe fails after reset() has been called. reset_control_rearm() keeps use of triggered_count sane in the reset framework, use of reset_control_reset() on shared reset line should be balanced with reset_control_rearm(). Signed-off-by: Amjad Ouled-Ameur <aouledameur@baylibre.com> Reported-by: Jerome Brunet <jbrunet@baylibre.com> --- Important: Please DO NOT merge before this patch [0] is merged, it adds reset_control_rearm() call to the reset framework API. [0] https://lore.kernel.org/lkml/20201112230043.28987-1-aouledameur@baylib re.com/ drivers/usb/dwc3/dwc3-meson-g12a.c | 19 +++++++++++++------ 1 file changed, 13 insertions(+), 6 deletions(-)