@@ -1,10 +1,10 @@
.. SPDX-License-Identifier: GPL-2.0+
-U-Boot for ODROID-C4
-====================
+U-Boot for ODROID-C4 (S905X3)
+=============================
-ODROID-C4 is a single board computer manufactured by Hardkernel
-Co. Ltd with the following specifications:
+ODROID-C4 is a Single Board Computer manufactured by Hardkernel with the following
+specifications:
- Amlogic S905X3 Arm Cortex-A55 quad-core SoC
- 4GB DDR4 SDRAM
@@ -17,12 +17,9 @@ Co. Ltd with the following specifications:
- UART serial
- Infrared receiver
-The ODROID-HC4 is a variant with a PCIe-SATA controller, the same commands
-applies for HC4.
-
Schematics are available on the manufacturer website.
-U-Boot compilation
+U-Boot Compilation
------------------
.. code-block:: bash
@@ -31,14 +28,20 @@ U-Boot compilation
$ make odroid-c4_defconfig
$ make
-Image creation
---------------
+U-Boot Signing with Pre-Built FIP repo
+--------------------------------------
+
+.. code-block:: bash
+ $ git clone https://github.com/LibreELEC/amlogic-boot-fip --depth=1
+ $ cd amlogic-boot-fip
+ $ mkdir my-output-dir
+ $ ./build-fip.sh odroid-c4 /path/to/u-boot/u-boot.bin my-output-dir
-For simplified usage, pleaser refer to :doc:`pre-generated-fip` with codename `odroid-c4` or `odroid-hc4`
+U-Boot Manual Signing
+---------------------
-Amlogic doesn't provide sources for the firmware and for tools needed
-to create the bootloader image, so it is necessary to obtain them from
-the git tree published by the board vendor:
+Amlogic does not provide sources for the firmware and tools needed to create a bootloader
+image so it is necessary to obtain binaries from sources published by the board vendor:
.. code-block:: bash
@@ -58,7 +61,7 @@ the git tree published by the board vendor:
$ make
$ export UBOOTDIR=$PWD
-Go back to mainline U-Boot source tree then :
+Go back to the mainline U-Boot source tree then:
.. code-block:: bash
@@ -82,58 +85,58 @@ Go back to mainline U-Boot source tree then :
$ cp u-boot.bin fip/bl33.bin
$ sh fip/blx_fix.sh \
- fip/bl30.bin \
- fip/zero_tmp \
- fip/bl30_zero.bin \
- fip/bl301.bin \
- fip/bl301_zero.bin \
- fip/bl30_new.bin \
- bl30
+ fip/bl30.bin \
+ fip/zero_tmp \
+ fip/bl30_zero.bin \
+ fip/bl301.bin \
+ fip/bl301_zero.bin \
+ fip/bl30_new.bin \
+ bl30
$ sh fip/blx_fix.sh \
- fip/bl2.bin \
- fip/zero_tmp \
- fip/bl2_zero.bin \
- fip/acs.bin \
- fip/bl21_zero.bin \
- fip/bl2_new.bin \
- bl2
+ fip/bl2.bin \
+ fip/zero_tmp \
+ fip/bl2_zero.bin \
+ fip/acs.bin \
+ fip/bl21_zero.bin \
+ fip/bl2_new.bin \
+ bl2
$ $UBOOTDIR/fip/g12a/aml_encrypt_g12a --bl30sig --input fip/bl30_new.bin \
- --output fip/bl30_new.bin.g12a.enc \
- --level v3
+ --output fip/bl30_new.bin.g12a.enc \
+ --level v3
$ $UBOOTDIR/fip/g12a/aml_encrypt_g12a --bl3sig --input fip/bl30_new.bin.g12a.enc \
- --output fip/bl30_new.bin.enc \
- --level v3 --type bl30
+ --output fip/bl30_new.bin.enc \
+ --level v3 --type bl30
$ $UBOOTDIR/fip/g12a/aml_encrypt_g12a --bl3sig --input fip/bl31.img \
- --output fip/bl31.img.enc \
- --level v3 --type bl31
+ --output fip/bl31.img.enc \
+ --level v3 --type bl31
$ $UBOOTDIR/fip/g12a/aml_encrypt_g12a --bl3sig --input fip/bl33.bin --compress lz4 \
- --output fip/bl33.bin.enc \
- --level v3 --type bl33 --compress lz4
+ --output fip/bl33.bin.enc \
+ --level v3 --type bl33 --compress lz4
$ $UBOOTDIR/fip/g12a/aml_encrypt_g12a --bl2sig --input fip/bl2_new.bin \
- --output fip/bl2.n.bin.sig
+ --output fip/bl2.n.bin.sig
$ $UBOOTDIR/fip/g12a/aml_encrypt_g12a --bootmk \
- --output fip/u-boot.bin \
- --bl2 fip/bl2.n.bin.sig \
- --bl30 fip/bl30_new.bin.enc \
- --bl31 fip/bl31.img.enc \
- --bl33 fip/bl33.bin.enc \
- --ddrfw1 fip/ddr4_1d.fw \
- --ddrfw2 fip/ddr4_2d.fw \
- --ddrfw3 fip/ddr3_1d.fw \
- --ddrfw4 fip/piei.fw \
- --ddrfw5 fip/lpddr4_1d.fw \
- --ddrfw6 fip/lpddr4_2d.fw \
- --ddrfw7 fip/diag_lpddr4.fw \
- --ddrfw8 fip/aml_ddr.fw \
- --ddrfw9 fip/lpddr3_1d.fw \
- --level v3
-
-and then write the image to SD with:
+ --output fip/u-boot.bin \
+ --bl2 fip/bl2.n.bin.sig \
+ --bl30 fip/bl30_new.bin.enc \
+ --bl31 fip/bl31.img.enc \
+ --bl33 fip/bl33.bin.enc \
+ --ddrfw1 fip/ddr4_1d.fw \
+ --ddrfw2 fip/ddr4_2d.fw \
+ --ddrfw3 fip/ddr3_1d.fw \
+ --ddrfw4 fip/piei.fw \
+ --ddrfw5 fip/lpddr4_1d.fw \
+ --ddrfw6 fip/lpddr4_2d.fw \
+ --ddrfw7 fip/diag_lpddr4.fw \
+ --ddrfw8 fip/aml_ddr.fw \
+ --ddrfw9 fip/lpddr3_1d.fw \
+ --level v3
+
+Then write the image to SD or eMMC with:
.. code-block:: bash
- $ DEV=/dev/your_sd_device
+ $ DEV=/dev/boot_device
$ dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=512 skip=1 seek=1
- $ dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=1 count=444
+ $ dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=1 count=440
Improve documentation. Notably drop references to the ODROID-HC4 board as its support has evolved and we will add an HC4 specific document in a later patch. Signed-off-by: Christian Hewitt <christianshewitt@gmail.com> --- doc/board/amlogic/odroid-c4.rst | 117 ++++++++++++++++---------------- 1 file changed, 60 insertions(+), 57 deletions(-)