| Message ID | 20230320114609.930145-34-christianshewitt@gmail.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | doc: board: amlogic: spring clean-up of Amlogic docs | expand |
On 3/20/23 12:46, Christian Hewitt wrote: > Add separate documentation for the ODROID-HC4 board to ensure > users build U-Boot using the HC4 defconfig that enables PCIe > SATA boot. This avoids user frustration trying to boot after > using the C4 recipe which only works from SD card. > > Signed-off-by: Christian Hewitt <christianshewitt@gmail.com> > --- > doc/board/amlogic/index.rst | 1 + > doc/board/amlogic/odroid-hc4.rst | 141 +++++++++++++++++++++++++++++++ > 2 files changed, 142 insertions(+) > create mode 100644 doc/board/amlogic/odroid-hc4.rst > > diff --git a/doc/board/amlogic/index.rst b/doc/board/amlogic/index.rst > index 7c4c161e0d..9b76bca427 100644 > --- a/doc/board/amlogic/index.rst > +++ b/doc/board/amlogic/index.rst > @@ -101,6 +101,7 @@ Board Documentation > nanopi-k2 > odroid-c2 > odroid-c4 > + odroid-hc4 > odroid-n2 > odroid-n2l > odroid-go-ultra > diff --git a/doc/board/amlogic/odroid-hc4.rst b/doc/board/amlogic/odroid-hc4.rst > new file mode 100644 > index 0000000000..94c3312022 > --- /dev/null > +++ b/doc/board/amlogic/odroid-hc4.rst > @@ -0,0 +1,141 @@ > +.. SPDX-License-Identifier: GPL-2.0+ > + > +U-Boot for ODROID-HC4 (S905X3) > +============================== > + > +ODROID-HC4 is a variant of the ODROID-C4 single board computer manufactured by Hardkernel > +with the following specification: > + > + - Amlogic S905X3 Arm Cortex-A55 quad-core SoC > + - 4GB DDR4 SDRAM > + - 16MB XT25F128B SPI-NOR flash > + - Gigabit Ethernet > + - HDMI 2.1 display > + - 7-pin GPIO header for OLED display and RTC > + - 1x USB 2.0 host (micro) > + - 2x SATA ports via ASM1061 PCIe to SATA controller > + - microSD > + - UART serial > + - Infrared receiver > + > +Schematics are available on the manufacturer website. > + > +U-Boot Compilation > +------------------ > + > +.. code-block:: bash > + > + $ export CROSS_COMPILE=aarch64-none-elf- > + $ make odroid-hc4_defconfig > + $ make > + > +U-Boot Signing with Pre-Built FIP repo > +-------------------------------------- > + > +.. code-block:: bash > + $ git clone https://github.com/LibreELEC/amlogic-boot-fip --depth=1 > + $ cd amlogic-boot-fip > + $ mkdir my-output-dir > + $ ./build-fip.sh odroid-hc4 /path/to/u-boot/u-boot.bin my-output-dir > + > +U-Boot Manual Signing > +--------------------- > + > +Amlogic does not provide sources for the firmware and tools needed to create a bootloader > +image so it is necessary to obtain binaries from sources published by the board vendor: > + > +.. code-block:: bash > + > + $ wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz > + $ wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz > + $ tar xvfJ gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz > + $ tar xvfJ gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz > + $ export PATH=$PWD/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux/bin:$PWD/gcc-linaro-arm-none-eabi-4.8-2013.11_linux/bin:$PATH > + > + $ DIR=odroid-hc4 > + $ git clone --depth 1 https://github.com/hardkernel/u-boot.git -b odroidg12-v2015.01 $DIR > + > + $ cd odroid-hc4 > + $ make odroidc4_defconfig > + $ make > + $ export UBOOTDIR=$PWD > + > +Go back to mainline U-Boot source tree then: > + > +.. code-block:: bash > + > + $ mkdir fip Thanks a lot for providing all these board descriptions. Prefixing with $ makes copy-/pasting multiple commands impossible. I personally feel distracted by the prompts. But if you really want those $ signs displayed, please, use .. prompt:: bash $ mkdir fip Best regards Heinrich > + > + $ wget https://github.com/BayLibre/u-boot/releases/download/v2017.11-libretech-cc/blx_fix_g12a.sh -O fip/blx_fix.sh > + $ cp $UBOOTDIR/build/scp_task/bl301.bin fip/ > + $ cp $UBOOTDIR/build/board/hardkernel/odroidc4/firmware/acs.bin fip/ > + $ cp $UBOOTDIR/fip/g12a/bl2.bin fip/ > + $ cp $UBOOTDIR/fip/g12a/bl30.bin fip/ > + $ cp $UBOOTDIR/fip/g12a/bl31.img fip/ > + $ cp $UBOOTDIR/fip/g12a/ddr3_1d.fw fip/ > + $ cp $UBOOTDIR/fip/g12a/ddr4_1d.fw fip/ > + $ cp $UBOOTDIR/fip/g12a/ddr4_2d.fw fip/ > + $ cp $UBOOTDIR/fip/g12a/diag_lpddr4.fw fip/ > + $ cp $UBOOTDIR/fip/g12a/lpddr3_1d.fw fip/ > + $ cp $UBOOTDIR/fip/g12a/lpddr4_1d.fw fip/ > + $ cp $UBOOTDIR/fip/g12a/lpddr4_2d.fw fip/ > + $ cp $UBOOTDIR/fip/g12a/piei.fw fip/ > + $ cp $UBOOTDIR/fip/g12a/aml_ddr.fw fip/ > + $ cp u-boot.bin fip/bl33.bin > + > + $ sh fip/blx_fix.sh \ > + fip/bl30.bin \ > + fip/zero_tmp \ > + fip/bl30_zero.bin \ > + fip/bl301.bin \ > + fip/bl301_zero.bin \ > + fip/bl30_new.bin \ > + bl30 > + > + $ sh fip/blx_fix.sh \ > + fip/bl2.bin \ > + fip/zero_tmp \ > + fip/bl2_zero.bin \ > + fip/acs.bin \ > + fip/bl21_zero.bin \ > + fip/bl2_new.bin \ > + bl2 > + > + $ $UBOOTDIR/fip/g12a/aml_encrypt_g12a --bl30sig --input fip/bl30_new.bin \ > + --output fip/bl30_new.bin.g12a.enc \ > + --level v3 > + $ $UBOOTDIR/fip/g12a/aml_encrypt_g12a --bl3sig --input fip/bl30_new.bin.g12a.enc \ > + --output fip/bl30_new.bin.enc \ > + --level v3 --type bl30 > + $ $UBOOTDIR/fip/g12a/aml_encrypt_g12a --bl3sig --input fip/bl31.img \ > + --output fip/bl31.img.enc \ > + --level v3 --type bl31 > + $ $UBOOTDIR/fip/g12a/aml_encrypt_g12a --bl3sig --input fip/bl33.bin --compress lz4 \ > + --output fip/bl33.bin.enc \ > + --level v3 --type bl33 --compress lz4 > + $ $UBOOTDIR/fip/g12a/aml_encrypt_g12a --bl2sig --input fip/bl2_new.bin \ > + --output fip/bl2.n.bin.sig > + $ $UBOOTDIR/fip/g12a/aml_encrypt_g12a --bootmk \ > + --output fip/u-boot.bin \ > + --bl2 fip/bl2.n.bin.sig \ > + --bl30 fip/bl30_new.bin.enc \ > + --bl31 fip/bl31.img.enc \ > + --bl33 fip/bl33.bin.enc \ > + --ddrfw1 fip/ddr4_1d.fw \ > + --ddrfw2 fip/ddr4_2d.fw \ > + --ddrfw3 fip/ddr3_1d.fw \ > + --ddrfw4 fip/piei.fw \ > + --ddrfw5 fip/lpddr4_1d.fw \ > + --ddrfw6 fip/lpddr4_2d.fw \ > + --ddrfw7 fip/diag_lpddr4.fw \ > + --ddrfw8 fip/aml_ddr.fw \ > + --ddrfw9 fip/lpddr3_1d.fw \ > + --level v3 > + > +Then write U-Boot to SD or SPI-NOR with: > + > +.. code-block:: bash > + > + $ DEV=/dev/boot_device > + $ dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=512 skip=1 seek=1 > + $ dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=1 count=440
diff --git a/doc/board/amlogic/index.rst b/doc/board/amlogic/index.rst index 7c4c161e0d..9b76bca427 100644 --- a/doc/board/amlogic/index.rst +++ b/doc/board/amlogic/index.rst @@ -101,6 +101,7 @@ Board Documentation nanopi-k2 odroid-c2 odroid-c4 + odroid-hc4 odroid-n2 odroid-n2l odroid-go-ultra diff --git a/doc/board/amlogic/odroid-hc4.rst b/doc/board/amlogic/odroid-hc4.rst new file mode 100644 index 0000000000..94c3312022 --- /dev/null +++ b/doc/board/amlogic/odroid-hc4.rst @@ -0,0 +1,141 @@ +.. SPDX-License-Identifier: GPL-2.0+ + +U-Boot for ODROID-HC4 (S905X3) +============================== + +ODROID-HC4 is a variant of the ODROID-C4 single board computer manufactured by Hardkernel +with the following specification: + + - Amlogic S905X3 Arm Cortex-A55 quad-core SoC + - 4GB DDR4 SDRAM + - 16MB XT25F128B SPI-NOR flash + - Gigabit Ethernet + - HDMI 2.1 display + - 7-pin GPIO header for OLED display and RTC + - 1x USB 2.0 host (micro) + - 2x SATA ports via ASM1061 PCIe to SATA controller + - microSD + - UART serial + - Infrared receiver + +Schematics are available on the manufacturer website. + +U-Boot Compilation +------------------ + +.. code-block:: bash + + $ export CROSS_COMPILE=aarch64-none-elf- + $ make odroid-hc4_defconfig + $ make + +U-Boot Signing with Pre-Built FIP repo +-------------------------------------- + +.. code-block:: bash + $ git clone https://github.com/LibreELEC/amlogic-boot-fip --depth=1 + $ cd amlogic-boot-fip + $ mkdir my-output-dir + $ ./build-fip.sh odroid-hc4 /path/to/u-boot/u-boot.bin my-output-dir + +U-Boot Manual Signing +--------------------- + +Amlogic does not provide sources for the firmware and tools needed to create a bootloader +image so it is necessary to obtain binaries from sources published by the board vendor: + +.. code-block:: bash + + $ wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz + $ wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz + $ tar xvfJ gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz + $ tar xvfJ gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz + $ export PATH=$PWD/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux/bin:$PWD/gcc-linaro-arm-none-eabi-4.8-2013.11_linux/bin:$PATH + + $ DIR=odroid-hc4 + $ git clone --depth 1 https://github.com/hardkernel/u-boot.git -b odroidg12-v2015.01 $DIR + + $ cd odroid-hc4 + $ make odroidc4_defconfig + $ make + $ export UBOOTDIR=$PWD + +Go back to mainline U-Boot source tree then: + +.. code-block:: bash + + $ mkdir fip + + $ wget https://github.com/BayLibre/u-boot/releases/download/v2017.11-libretech-cc/blx_fix_g12a.sh -O fip/blx_fix.sh + $ cp $UBOOTDIR/build/scp_task/bl301.bin fip/ + $ cp $UBOOTDIR/build/board/hardkernel/odroidc4/firmware/acs.bin fip/ + $ cp $UBOOTDIR/fip/g12a/bl2.bin fip/ + $ cp $UBOOTDIR/fip/g12a/bl30.bin fip/ + $ cp $UBOOTDIR/fip/g12a/bl31.img fip/ + $ cp $UBOOTDIR/fip/g12a/ddr3_1d.fw fip/ + $ cp $UBOOTDIR/fip/g12a/ddr4_1d.fw fip/ + $ cp $UBOOTDIR/fip/g12a/ddr4_2d.fw fip/ + $ cp $UBOOTDIR/fip/g12a/diag_lpddr4.fw fip/ + $ cp $UBOOTDIR/fip/g12a/lpddr3_1d.fw fip/ + $ cp $UBOOTDIR/fip/g12a/lpddr4_1d.fw fip/ + $ cp $UBOOTDIR/fip/g12a/lpddr4_2d.fw fip/ + $ cp $UBOOTDIR/fip/g12a/piei.fw fip/ + $ cp $UBOOTDIR/fip/g12a/aml_ddr.fw fip/ + $ cp u-boot.bin fip/bl33.bin + + $ sh fip/blx_fix.sh \ + fip/bl30.bin \ + fip/zero_tmp \ + fip/bl30_zero.bin \ + fip/bl301.bin \ + fip/bl301_zero.bin \ + fip/bl30_new.bin \ + bl30 + + $ sh fip/blx_fix.sh \ + fip/bl2.bin \ + fip/zero_tmp \ + fip/bl2_zero.bin \ + fip/acs.bin \ + fip/bl21_zero.bin \ + fip/bl2_new.bin \ + bl2 + + $ $UBOOTDIR/fip/g12a/aml_encrypt_g12a --bl30sig --input fip/bl30_new.bin \ + --output fip/bl30_new.bin.g12a.enc \ + --level v3 + $ $UBOOTDIR/fip/g12a/aml_encrypt_g12a --bl3sig --input fip/bl30_new.bin.g12a.enc \ + --output fip/bl30_new.bin.enc \ + --level v3 --type bl30 + $ $UBOOTDIR/fip/g12a/aml_encrypt_g12a --bl3sig --input fip/bl31.img \ + --output fip/bl31.img.enc \ + --level v3 --type bl31 + $ $UBOOTDIR/fip/g12a/aml_encrypt_g12a --bl3sig --input fip/bl33.bin --compress lz4 \ + --output fip/bl33.bin.enc \ + --level v3 --type bl33 --compress lz4 + $ $UBOOTDIR/fip/g12a/aml_encrypt_g12a --bl2sig --input fip/bl2_new.bin \ + --output fip/bl2.n.bin.sig + $ $UBOOTDIR/fip/g12a/aml_encrypt_g12a --bootmk \ + --output fip/u-boot.bin \ + --bl2 fip/bl2.n.bin.sig \ + --bl30 fip/bl30_new.bin.enc \ + --bl31 fip/bl31.img.enc \ + --bl33 fip/bl33.bin.enc \ + --ddrfw1 fip/ddr4_1d.fw \ + --ddrfw2 fip/ddr4_2d.fw \ + --ddrfw3 fip/ddr3_1d.fw \ + --ddrfw4 fip/piei.fw \ + --ddrfw5 fip/lpddr4_1d.fw \ + --ddrfw6 fip/lpddr4_2d.fw \ + --ddrfw7 fip/diag_lpddr4.fw \ + --ddrfw8 fip/aml_ddr.fw \ + --ddrfw9 fip/lpddr3_1d.fw \ + --level v3 + +Then write U-Boot to SD or SPI-NOR with: + +.. code-block:: bash + + $ DEV=/dev/boot_device + $ dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=512 skip=1 seek=1 + $ dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=1 count=440
Add separate documentation for the ODROID-HC4 board to ensure users build U-Boot using the HC4 defconfig that enables PCIe SATA boot. This avoids user frustration trying to boot after using the C4 recipe which only works from SD card. Signed-off-by: Christian Hewitt <christianshewitt@gmail.com> --- doc/board/amlogic/index.rst | 1 + doc/board/amlogic/odroid-hc4.rst | 141 +++++++++++++++++++++++++++++++ 2 files changed, 142 insertions(+) create mode 100644 doc/board/amlogic/odroid-hc4.rst