| Message ID | 20190325074523.26456-1-josephl@nvidia.com (mailing list archive) |
|---|---|
| Headers | show |
| Series | Add EMC scaling support for Tegra210 | expand |
Looks ok to me. Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com> On Mon, Mar 25, 2019 at 03:45:15PM +0800, Joseph Lo wrote: > This series introduces the EMC clock scaling support for Tegra210. There > are three parts of this series. > > i. The DT bindings of the EMC table and how to deal with them. > To support LPDDR4 DRAM devices, the EMC table with timing data must be > trained before it can be used. The bootloader firmware will help to do > that at the early boot stage. And help to merge the trained timing data > into the DTB that EMC driver in the kernel will use later for EMC clock > scaling. > > And for backward compatibility to support the upstreaming devices, like > Jetson TX1 and Shield, the bindings should remain the same. Which means > we may not able to change the bindings currently. > > ii. The EMC driver will use the trained EMC table with the ram code that > the platform used to update the EMC registers for clock scaling. And to > support higher rates (above 800MHz), periodic training is needed. This > will be done by a timer. And two EMC sources will be used (PLL_M and > PLL_MB) for the rate switching above or equal to 665MHz. > It will check the current source and switch to another one dynamically. > > iii. The detail sequence for EMC scaling support, this includes how we > update the table to EMC registers and the periodic training support. > > Here are the details and dependency of these patches. > Patch 1 is the binding document of the EMC node and table. > Patch 2 is the clock driver update for EMC scaling support. Need to note > that with the update of the MC clock, the patch 3 (EMC clock driver) and > patch 6 (EMC node in DT) will be needed to make MC clock to work > normally. > Patch 3 is the EMC clock driver. It can get the trained table from the > firmware and know the current EMC status, like the rate and source > clock. > Patch 4 adds more APIs and support code. Tha will be needed for the EMC > scaling sequence. > Patch 5 adds the EMC scaling sequence code. With this, we can support > EMC clock scaling now. > Patch 6 introduces the EMC node in DT. > Patch 7 adds EMC table of ram code 0. > Patch 8 adds EMC table of ram code 1. > > Joseph Lo (8): > dt-bindings: memory: tegra: Add Tegra210 EMC bindings > clk: tegra: clock changes for emc scaling support on Tegra210 > memory: tegra: Add Tegra210 EMC clock driver > memory: tegra: add EMC scaling support code for Tegra210 > memory: tegra: Add EMC scaling sequence code for Tegra210 > arm64: tegra: Add external memory controller node for Tegra210 > arm64: tegra: Add EMC table of ram code 0 for Tegra210 Shield platform > arm64: tegra: Add EMC table of ram code 1 for Tegra210 Shield platform > > .../nvidia,tegra210-emc.txt | 605 + > .../boot/dts/nvidia/tegra210-p2894-emc.dtsi | 24851 ++++++++++++++++ > .../arm64/boot/dts/nvidia/tegra210-p2894.dtsi | 1 + > arch/arm64/boot/dts/nvidia/tegra210.dtsi | 23 + > drivers/clk/tegra/clk-tegra210.c | 112 +- > drivers/memory/tegra/Kconfig | 10 + > drivers/memory/tegra/Makefile | 1 + > drivers/memory/tegra/tegra210-dt-parse.c | 340 + > drivers/memory/tegra/tegra210-emc-cc-r21021.c | 1962 ++ > drivers/memory/tegra/tegra210-emc-reg.h | 1482 + > drivers/memory/tegra/tegra210-emc.c | 1814 ++ > include/dt-bindings/clock/tegra210-car.h | 4 +- > include/linux/clk/tegra.h | 5 + > 13 files changed, 31192 insertions(+), 18 deletions(-) > create mode 100644 Documentation/devicetree/bindings/memory-controllers/nvidia,tegra210-emc.txt > create mode 100644 arch/arm64/boot/dts/nvidia/tegra210-p2894-emc.dtsi > create mode 100644 drivers/memory/tegra/tegra210-dt-parse.c > create mode 100644 drivers/memory/tegra/tegra210-emc-cc-r21021.c > create mode 100644 drivers/memory/tegra/tegra210-emc-reg.h > create mode 100644 drivers/memory/tegra/tegra210-emc.c > > -- > 2.21.0 >