| Message ID | 20200701103126.1512615-1-megous@megous.com (mailing list archive) |
|---|---|
| Headers | show |
| Series | Add support for PinePhone LCD panel | expand |
Hi Ondrej. On Wed, Jul 01, 2020 at 12:31:13PM +0200, Ondrej Jirman wrote: > This patchset adds support for the LCD panel of PinePhone. > > I've tested this on PinePhone 1.0 and 1.2. > > Please take a look. > > thank you and regards, > Ondrej Jirman > > Changes in v6: > - Fixed spacing in yaml > - Fixed wrong vccio->iovcc supply name in the bindings doc > - I noticed that the original driver uses a delay of 20ms in the init > function to achieve a combined total of 120ms required from post-reset > to display_on. I've added a similar delay to xbd599_init, so that > xbd599 panel also has the right timing. (patch 9) > - v5->v6 diff: https://megous.com/dl/tmp/v5-v6.patch > - Added review/ack tags > - Learned to run dt_binding_check by myself ;) The patch-set does not apply clean on top of drm-misc-next - due to vrefresh removal. Please re-spin. Sam
Hi, On Wed, Jul 01, 2020 at 12:31:13PM +0200, Ondrej Jirman wrote: > This patchset adds support for the LCD panel of PinePhone. I gave this a quick spin on the Librem5 devkit so Tested-by: Guido Günther <agx@sigxcpu.org> but please also adjust MAINTAINERS so we stay in the loop on driver changes. Cheers, -- Guido > > I've tested this on PinePhone 1.0 and 1.2. > > Please take a look. > > thank you and regards, > Ondrej Jirman > > Changes in v6: > - Fixed spacing in yaml > - Fixed wrong vccio->iovcc supply name in the bindings doc > - I noticed that the original driver uses a delay of 20ms in the init > function to achieve a combined total of 120ms required from post-reset > to display_on. I've added a similar delay to xbd599_init, so that > xbd599 panel also has the right timing. (patch 9) > - v5->v6 diff: https://megous.com/dl/tmp/v5-v6.patch > - Added review/ack tags > - Learned to run dt_binding_check by myself ;) > > Changes in v5: > - rewritten on top of rocktech-jh057n00900 driver > - rocktech-jh057n00900 renamed to st7703 (controller name) > - converted rocktech-jh057n00900 bindings to yaml and extended for xbd599 > > Changes in v4: > - use ->type from the mode instead of hardcoding (Samuel) > - move init_sequence to ->prepare (Samuel) > - move anti-flicker delay to ->enable, explain it (Samuel) > - add enter_sleep after display_off (Samuel) > - drop ->disable (move code to ->unprepare) > - add ID bytes dumping (Linus) > (I can't test it since allwinner DSI driver has a broken > dcs_read function, and I didn't manage to fix it.) > - document magic bytes (Linus) > - assert reset during powerup > - cleanup powerup timings according to the datasheet > > Changes in v3: > - Panel driver renamed to the name of the LCD controller > - Re-organize the driver slightly to more easily support more panels > based on the same controller. > - Add patch to enable the touchscreen to complete the LCD support > on PinePhone. > - Dropped the "DSI fix" patch (the driver seems to work for me without it) > - Improved brightness levels handling: > - PinePhone 1.0 uses default levels generated by the driver > - On PinePhone 1.1 duty cycles < 20% lead to black screen, so > default levels can't be used. Martijn Braam came up with a > list of duty cycle values that lead to perception of linear > brigtness level <-> light intensity on PinePhone 1.1 > - There was some feedback on v2 about this being similar to st7701. > It's only similar in name. Most of the "user commands" are different, > so I opted to keep this in a new driver instead of creating st770x. > > Anyone who likes to check the differences, here are datasheets: > > - https://megous.com/dl/tmp/ST7703_DS_v01_20160128.pdf > - https://megous.com/dl/tmp/ST7701.pdf > > Changes in v2: > - DT Example fix. > - DT Format fix. > - Raised copyright info to 2020. > - Sort panel operation functions. > - Sort inclusion. > > > -- For phone owners: -- > > There's an open question on how to set the backlight brightness values > on post 1.0 revision phone, since lower duty cycles (< 10-20%) lead > to backlight being black. It would be nice if more people can test > the various backlight levels on 1.1 and 1.2 revision with this change > in dts: > > brightness-levels = <0 1000>; > num-interpolated-steps = <1000>; > > and report at what brightness level the backlight turns on. So far it > seems this has a wide range. Lowest useable duty cycle for me is ~7% > on 1.2 and for Martijn ~20% on 1.1. > > Icenowy Zheng (2): > dt-bindings: vendor-prefixes: Add Xingbangda > arm64: dts: sun50i-a64-pinephone: Enable LCD support on PinePhone > > Ondrej Jirman (11): > dt-bindings: panel: Convert rocktech,jh057n00900 to yaml > dt-bindings: panel: Add compatible for Xingbangda XBD599 panel > drm/panel: rocktech-jh057n00900: Rename the driver to st7703 > drm/panel: st7703: Rename functions from jh057n prefix to st7703 > drm/panel: st7703: Prepare for supporting multiple panels > drm/panel: st7703: Move code specific to jh057n closer together > drm/panel: st7703: Move generic part of init sequence to enable > callback > drm/panel: st7703: Add support for Xingbangda XBD599 > drm/panel: st7703: Enter sleep after display off > drm/panel: st7703: Assert reset prior to powering down the regulators > arm64: dts: sun50i-a64-pinephone: Add touchscreen support > > .../display/panel/rocktech,jh057n00900.txt | 23 - > .../display/panel/rocktech,jh057n00900.yaml | 70 ++ > .../devicetree/bindings/vendor-prefixes.yaml | 2 + > .../allwinner/sun50i-a64-pinephone-1.1.dts | 19 + > .../dts/allwinner/sun50i-a64-pinephone.dtsi | 54 ++ > drivers/gpu/drm/panel/Kconfig | 26 +- > drivers/gpu/drm/panel/Makefile | 2 +- > .../drm/panel/panel-rocktech-jh057n00900.c | 424 ----------- > drivers/gpu/drm/panel/panel-sitronix-st7703.c | 656 ++++++++++++++++++ > 9 files changed, 815 insertions(+), 461 deletions(-) > delete mode 100644 Documentation/devicetree/bindings/display/panel/rocktech,jh057n00900.txt > create mode 100644 Documentation/devicetree/bindings/display/panel/rocktech,jh057n00900.yaml > delete mode 100644 drivers/gpu/drm/panel/panel-rocktech-jh057n00900.c > create mode 100644 drivers/gpu/drm/panel/panel-sitronix-st7703.c > > -- > 2.27.0 >
Hello Sam, On Wed, Jul 01, 2020 at 05:25:32PM +0200, Sam Ravnborg wrote: > Hi Ondrej. > > On Wed, Jul 01, 2020 at 12:31:13PM +0200, Ondrej Jirman wrote: > > This patchset adds support for the LCD panel of PinePhone. > > > > I've tested this on PinePhone 1.0 and 1.2. > > > > Please take a look. > > > > thank you and regards, > > Ondrej Jirman > > > > Changes in v6: > > - Fixed spacing in yaml > > - Fixed wrong vccio->iovcc supply name in the bindings doc > > - I noticed that the original driver uses a delay of 20ms in the init > > function to achieve a combined total of 120ms required from post-reset > > to display_on. I've added a similar delay to xbd599_init, so that > > xbd599 panel also has the right timing. (patch 9) > > - v5->v6 diff: https://megous.com/dl/tmp/v5-v6.patch > > - Added review/ack tags > > - Learned to run dt_binding_check by myself ;) > The patch-set does not apply clean on top of drm-misc-next - due to > vrefresh removal. > Please re-spin. Sorry for that. Rebased and retested. thank you, o. > Sam
On Wed, Jul 1, 2020 at 6:30 PM Ondřej Jirman <megous@megous.com> wrote: > On Wed, Jul 01, 2020 at 05:25:32PM +0200, Sam Ravnborg wrote: > > Hi Ondrej. > > > > On Wed, Jul 01, 2020 at 12:31:13PM +0200, Ondrej Jirman wrote: > > > This patchset adds support for the LCD panel of PinePhone. > > > > > > I've tested this on PinePhone 1.0 and 1.2. > > > > > > Please take a look. > > > > > > thank you and regards, > > > Ondrej Jirman > > > > > > Changes in v6: > > > - Fixed spacing in yaml > > > - Fixed wrong vccio->iovcc supply name in the bindings doc > > > - I noticed that the original driver uses a delay of 20ms in the init > > > function to achieve a combined total of 120ms required from post-reset > > > to display_on. I've added a similar delay to xbd599_init, so that > > > xbd599 panel also has the right timing. (patch 9) > > > - v5->v6 diff: https://megous.com/dl/tmp/v5-v6.patch > > > - Added review/ack tags > > > - Learned to run dt_binding_check by myself ;) > > The patch-set does not apply clean on top of drm-misc-next - due to > > vrefresh removal. > > Please re-spin. > > Sorry for that. Rebased and retested. Sam will you apply it? I was in the middle of applying and ran into the same issue :D Yours, Linus Walleij
Hello, On Wed, Jul 01, 2020 at 05:54:05PM +0200, Guido Günther wrote: > Hi, > On Wed, Jul 01, 2020 at 12:31:13PM +0200, Ondrej Jirman wrote: > > This patchset adds support for the LCD panel of PinePhone. > > I gave this a quick spin on the Librem5 devkit so > > Tested-by: Guido Günther <agx@sigxcpu.org> > > but please also adjust MAINTAINERS so we stay in the loop on driver > changes. Ah, right. I'll send a quick followup patch[1] after this gets merged, or add it to v8 if there will be a need for v8. Thanks for noticing. [1] https://megous.com/dl/tmp/0001-MAINTAINERS-Update-entry-for-st7703-driver-after-the.patch And thanks for testing, too. :) regards, o. > Cheers, > -- Guido > > > > > I've tested this on PinePhone 1.0 and 1.2. > > > > Please take a look. > > > > thank you and regards, > > Ondrej Jirman > > > > Changes in v6: > > - Fixed spacing in yaml > > - Fixed wrong vccio->iovcc supply name in the bindings doc > > - I noticed that the original driver uses a delay of 20ms in the init > > function to achieve a combined total of 120ms required from post-reset > > to display_on. I've added a similar delay to xbd599_init, so that > > xbd599 panel also has the right timing. (patch 9) > > - v5->v6 diff: https://megous.com/dl/tmp/v5-v6.patch > > - Added review/ack tags > > - Learned to run dt_binding_check by myself ;) > > > > Changes in v5: > > - rewritten on top of rocktech-jh057n00900 driver > > - rocktech-jh057n00900 renamed to st7703 (controller name) > > - converted rocktech-jh057n00900 bindings to yaml and extended for xbd599 > > > > Changes in v4: > > - use ->type from the mode instead of hardcoding (Samuel) > > - move init_sequence to ->prepare (Samuel) > > - move anti-flicker delay to ->enable, explain it (Samuel) > > - add enter_sleep after display_off (Samuel) > > - drop ->disable (move code to ->unprepare) > > - add ID bytes dumping (Linus) > > (I can't test it since allwinner DSI driver has a broken > > dcs_read function, and I didn't manage to fix it.) > > - document magic bytes (Linus) > > - assert reset during powerup > > - cleanup powerup timings according to the datasheet > > > > Changes in v3: > > - Panel driver renamed to the name of the LCD controller > > - Re-organize the driver slightly to more easily support more panels > > based on the same controller. > > - Add patch to enable the touchscreen to complete the LCD support > > on PinePhone. > > - Dropped the "DSI fix" patch (the driver seems to work for me without it) > > - Improved brightness levels handling: > > - PinePhone 1.0 uses default levels generated by the driver > > - On PinePhone 1.1 duty cycles < 20% lead to black screen, so > > default levels can't be used. Martijn Braam came up with a > > list of duty cycle values that lead to perception of linear > > brigtness level <-> light intensity on PinePhone 1.1 > > - There was some feedback on v2 about this being similar to st7701. > > It's only similar in name. Most of the "user commands" are different, > > so I opted to keep this in a new driver instead of creating st770x. > > > > Anyone who likes to check the differences, here are datasheets: > > > > - https://megous.com/dl/tmp/ST7703_DS_v01_20160128.pdf > > - https://megous.com/dl/tmp/ST7701.pdf > > > > Changes in v2: > > - DT Example fix. > > - DT Format fix. > > - Raised copyright info to 2020. > > - Sort panel operation functions. > > - Sort inclusion. > > > > > > -- For phone owners: -- > > > > There's an open question on how to set the backlight brightness values > > on post 1.0 revision phone, since lower duty cycles (< 10-20%) lead > > to backlight being black. It would be nice if more people can test > > the various backlight levels on 1.1 and 1.2 revision with this change > > in dts: > > > > brightness-levels = <0 1000>; > > num-interpolated-steps = <1000>; > > > > and report at what brightness level the backlight turns on. So far it > > seems this has a wide range. Lowest useable duty cycle for me is ~7% > > on 1.2 and for Martijn ~20% on 1.1. > > > > Icenowy Zheng (2): > > dt-bindings: vendor-prefixes: Add Xingbangda > > arm64: dts: sun50i-a64-pinephone: Enable LCD support on PinePhone > > > > Ondrej Jirman (11): > > dt-bindings: panel: Convert rocktech,jh057n00900 to yaml > > dt-bindings: panel: Add compatible for Xingbangda XBD599 panel > > drm/panel: rocktech-jh057n00900: Rename the driver to st7703 > > drm/panel: st7703: Rename functions from jh057n prefix to st7703 > > drm/panel: st7703: Prepare for supporting multiple panels > > drm/panel: st7703: Move code specific to jh057n closer together > > drm/panel: st7703: Move generic part of init sequence to enable > > callback > > drm/panel: st7703: Add support for Xingbangda XBD599 > > drm/panel: st7703: Enter sleep after display off > > drm/panel: st7703: Assert reset prior to powering down the regulators > > arm64: dts: sun50i-a64-pinephone: Add touchscreen support > > > > .../display/panel/rocktech,jh057n00900.txt | 23 - > > .../display/panel/rocktech,jh057n00900.yaml | 70 ++ > > .../devicetree/bindings/vendor-prefixes.yaml | 2 + > > .../allwinner/sun50i-a64-pinephone-1.1.dts | 19 + > > .../dts/allwinner/sun50i-a64-pinephone.dtsi | 54 ++ > > drivers/gpu/drm/panel/Kconfig | 26 +- > > drivers/gpu/drm/panel/Makefile | 2 +- > > .../drm/panel/panel-rocktech-jh057n00900.c | 424 ----------- > > drivers/gpu/drm/panel/panel-sitronix-st7703.c | 656 ++++++++++++++++++ > > 9 files changed, 815 insertions(+), 461 deletions(-) > > delete mode 100644 Documentation/devicetree/bindings/display/panel/rocktech,jh057n00900.txt > > create mode 100644 Documentation/devicetree/bindings/display/panel/rocktech,jh057n00900.yaml > > delete mode 100644 drivers/gpu/drm/panel/panel-rocktech-jh057n00900.c > > create mode 100644 drivers/gpu/drm/panel/panel-sitronix-st7703.c > > > > -- > > 2.27.0 > >
This patchset adds support for the LCD panel of PinePhone. I've tested this on PinePhone 1.0 and 1.2. Please take a look. thank you and regards, Ondrej Jirman Changes in v6: - Fixed spacing in yaml - Fixed wrong vccio->iovcc supply name in the bindings doc - I noticed that the original driver uses a delay of 20ms in the init function to achieve a combined total of 120ms required from post-reset to display_on. I've added a similar delay to xbd599_init, so that xbd599 panel also has the right timing. (patch 9) - v5->v6 diff: https://megous.com/dl/tmp/v5-v6.patch - Added review/ack tags - Learned to run dt_binding_check by myself ;) Changes in v5: - rewritten on top of rocktech-jh057n00900 driver - rocktech-jh057n00900 renamed to st7703 (controller name) - converted rocktech-jh057n00900 bindings to yaml and extended for xbd599 Changes in v4: - use ->type from the mode instead of hardcoding (Samuel) - move init_sequence to ->prepare (Samuel) - move anti-flicker delay to ->enable, explain it (Samuel) - add enter_sleep after display_off (Samuel) - drop ->disable (move code to ->unprepare) - add ID bytes dumping (Linus) (I can't test it since allwinner DSI driver has a broken dcs_read function, and I didn't manage to fix it.) - document magic bytes (Linus) - assert reset during powerup - cleanup powerup timings according to the datasheet Changes in v3: - Panel driver renamed to the name of the LCD controller - Re-organize the driver slightly to more easily support more panels based on the same controller. - Add patch to enable the touchscreen to complete the LCD support on PinePhone. - Dropped the "DSI fix" patch (the driver seems to work for me without it) - Improved brightness levels handling: - PinePhone 1.0 uses default levels generated by the driver - On PinePhone 1.1 duty cycles < 20% lead to black screen, so default levels can't be used. Martijn Braam came up with a list of duty cycle values that lead to perception of linear brigtness level <-> light intensity on PinePhone 1.1 - There was some feedback on v2 about this being similar to st7701. It's only similar in name. Most of the "user commands" are different, so I opted to keep this in a new driver instead of creating st770x. Anyone who likes to check the differences, here are datasheets: - https://megous.com/dl/tmp/ST7703_DS_v01_20160128.pdf - https://megous.com/dl/tmp/ST7701.pdf Changes in v2: - DT Example fix. - DT Format fix. - Raised copyright info to 2020. - Sort panel operation functions. - Sort inclusion. -- For phone owners: -- There's an open question on how to set the backlight brightness values on post 1.0 revision phone, since lower duty cycles (< 10-20%) lead to backlight being black. It would be nice if more people can test the various backlight levels on 1.1 and 1.2 revision with this change in dts: brightness-levels = <0 1000>; num-interpolated-steps = <1000>; and report at what brightness level the backlight turns on. So far it seems this has a wide range. Lowest useable duty cycle for me is ~7% on 1.2 and for Martijn ~20% on 1.1. Icenowy Zheng (2): dt-bindings: vendor-prefixes: Add Xingbangda arm64: dts: sun50i-a64-pinephone: Enable LCD support on PinePhone Ondrej Jirman (11): dt-bindings: panel: Convert rocktech,jh057n00900 to yaml dt-bindings: panel: Add compatible for Xingbangda XBD599 panel drm/panel: rocktech-jh057n00900: Rename the driver to st7703 drm/panel: st7703: Rename functions from jh057n prefix to st7703 drm/panel: st7703: Prepare for supporting multiple panels drm/panel: st7703: Move code specific to jh057n closer together drm/panel: st7703: Move generic part of init sequence to enable callback drm/panel: st7703: Add support for Xingbangda XBD599 drm/panel: st7703: Enter sleep after display off drm/panel: st7703: Assert reset prior to powering down the regulators arm64: dts: sun50i-a64-pinephone: Add touchscreen support .../display/panel/rocktech,jh057n00900.txt | 23 - .../display/panel/rocktech,jh057n00900.yaml | 70 ++ .../devicetree/bindings/vendor-prefixes.yaml | 2 + .../allwinner/sun50i-a64-pinephone-1.1.dts | 19 + .../dts/allwinner/sun50i-a64-pinephone.dtsi | 54 ++ drivers/gpu/drm/panel/Kconfig | 26 +- drivers/gpu/drm/panel/Makefile | 2 +- .../drm/panel/panel-rocktech-jh057n00900.c | 424 ----------- drivers/gpu/drm/panel/panel-sitronix-st7703.c | 656 ++++++++++++++++++ 9 files changed, 815 insertions(+), 461 deletions(-) delete mode 100644 Documentation/devicetree/bindings/display/panel/rocktech,jh057n00900.txt create mode 100644 Documentation/devicetree/bindings/display/panel/rocktech,jh057n00900.yaml delete mode 100644 drivers/gpu/drm/panel/panel-rocktech-jh057n00900.c create mode 100644 drivers/gpu/drm/panel/panel-sitronix-st7703.c