[v10,00/27] Add i2c-mux and eeprom devices for Meta Yosemite 4

Message

Delphine CC Chiu July 19, 2024, 5:58 a.m. UTC

Changelog:
  - v10
    - adjust mgm cpld ioexp bus
    - add GPIOO7 name
    - remove mctp driver
  - v9
    - add XDP710 support
    - add RTQ6056 support
    - add MP5990 support
  - v8
    - add fan led config
  - v7
    - Revise pca9506 i2c address
  - v6
    - Revise i2c duty-cycle for meeting 400khz spec
  - v5
    - Support medusa board adc sensors
    - support NIC eeprom
  - v4
    - Re-format gpio linename
    - Revise i2c device node names
    - Split patches by logic changes
  - v3
    - Correct patch for revising gpio name
  - v2
    - Revise mx31790 fan tach config
    - Add mctp config for NIC
    - Support mux to cpld
    - Revise gpio name
  - v1
    - Add gpio and eeprom behind i2c-mux
    - Remove redundant idle-state setting for i2c-mux
    - Enable adc 15, wdt2,spi gpio for yosemite4 use
    - Revise quad mode to dual mode to avoid WP pin influnece the SPI
    - Revise power sensor adm1281 for yosemite4 schematic change
    - Add gpio pca9506 I/O expander for yosemite4 use
    - remove space for adm1272 compatible
    - enable interrupt setting for pca9555
    - add eeprom for yosemite4 medusa board/BSM use
    - remove temperature sensor for yosemite4 schematic change
    - add power sensor for power module reading
    - Revise adc128d818 adc mode for yosemite4 schematic change
    - Revise ina233 for yosemite4 schematic change
    - Remove idle state setting for yosemite4 NIC connection
    - Initialize bmc gpio state
    - Revise mx31790 fan tach config
    - Add mctp config for NIC
    - Support mux to cpld
    - Revise gpio name

Delphine CC Chiu (27):
  ARM: dts: aspeed: yosemite4: Revise i2c-mux devices
  ARM: dts: aspeed: yosemite4: Enable adc15
  ARM: dts: aspeed: yosemite4: Enable spi-gpio setting
  ARM: dts: aspeed: yosemite4: Enable watchdog2
  ARM: dts: aspeed: yosemite4: Revise quad mode to dual mode
  ARM: dts: aspeed: yosemite4: Revise power sensor adm1281 for schematic
    change
  ARM: dts: aspeed: yosemite4: Add gpio pca9506
  ARM: dts: aspeed: yosemite4: Remove space for adm1272 compatible
  ARM: dts: aspeed: yosemite4: Enable interrupt setting for pca9555
  ARM: dts: aspeed: yosemite4: Add power sensor for power module reading
  ARM: dts: aspeed: yosemite4: Add eeprom for yosemite4 use
  ARM: dts: aspeed: yosemite4: Remove temperature sensor for yosemite4
    schematic change
  ARM: dts: aspeed: yosemite4: Revise adc128d818 adc mode for yosemite4
    schematic change
  ARM: dts: aspeed: yosemite4: Revise ina233 config for yosemite4
    schematic change
  ARM: dts: aspeed: yosemite4: Remove idle state setting for yosemite4
    NIC connection
  ARM: dts: aspeed: yosemite4: Initialize bmc gpio state
  ARM: dts: aspeed: yosemite4: Revise mx31790 fan tach config
  ARM: dts: aspeed: yosemite4: add mctp config for NIC
  ARM: dts: aspeed: yosemite4: support mux to cpld
  ARM: dts: aspeed: yosemite4: support medusa board adc sensors
  ARM: dts: aspeed: yosemite4: support NIC eeprom
  ARM: dts: aspeed: yosemite4: Revise i2c duty-cycle
  ARM: dts: aspeed: yosemite4: add fan led config
  ARM: dts: aspeed: yosemite4: add XDP710
  ARM: dts: aspeed: yosemite4: add RTQ6056 support
  ARM: dts: aspeed: yosemite4: add MP5990 support
  ARM: dts: aspeed: yosemite4: Adjust ioexp bus and remove mctp driver

 .../aspeed/aspeed-bmc-facebook-yosemite4.dts  | 1421 +++++++++++++++--
 1 file changed, 1311 insertions(+), 110 deletions(-)