@@ -50,6 +50,9 @@
cmpcc \irqnr, \irqnr
cmpne \irqnr, \tmp
cmpcs \irqnr, \irqnr
+#ifdef HAVE_GIC_BASE_OFFSET
+ compute_irqnr \irqnr, \tmp
+#endif
.endm
/* We assume that irqstat (the raw value of the IRQ acknowledge
@@ -9,66 +9,16 @@
* warranty of any kind, whether express or implied.
*/
-#include <mach/hardware.h>
-#include <asm/hardware/gic.h>
+#define HAVE_GIC_BASE_OFFSET 1
+#include <asm/hardware/entry-macro-gic.S>
- .macro disable_fiq
+ .macro compute_irqnr, irqnr, tmp
+ addne \irqnr, #32
.endm
- .macro get_irqnr_preamble, base, tmp
- ldr \base, =gic_cpu_base_addr
- ldr \base, [\base]
+ .macro disable_fiq
.endm
.macro arch_ret_to_user, tmp1, tmp2
.endm
- /*
- * The interrupt numbering scheme is defined in the
- * interrupt controller spec. To wit:
- *
- * Interrupts 0-15 are IPI
- * 16-28 are reserved
- * 29-31 are local. We allow 30 to be used for the watchdog.
- * 32-1020 are global
- * 1021-1022 are reserved
- * 1023 is "spurious" (no interrupt)
- *
- * For now, we ignore all local interrupts so only return an interrupt if it's
- * between 30 and 1020. The test_for_ipi routine below will pick up on IPIs.
- *
- * A simple read from the controller will tell us the number of the highest
- * priority enabled interrupt. We then just need to check whether it is in the
- * valid range for an IRQ (30-1020 inclusive).
- */
-
- .macro get_irqnr_and_base, irqnr, irqstat, base, tmp
-
- ldr \irqstat, [\base, #GIC_CPU_INTACK] /* bits 12-10 = src CPU, 9-0 = int # */
-
- ldr \tmp, =1021
-
- bic \irqnr, \irqstat, #0x1c00
-
- cmp \irqnr, #15
- cmpcc \irqnr, \irqnr
- cmpne \irqnr, \tmp
- cmpcs \irqnr, \irqnr
- addne \irqnr, \irqnr, #32
-
- .endm
-
- /* We assume that irqstat (the raw value of the IRQ acknowledge
- * register) is preserved from the macro above.
- * If there is an IPI, we immediately signal end of interrupt on the
- * controller, since this requires the original irqstat value which
- * we won't easily be able to recreate later.
- */
-
- .macro test_for_ipi, irqnr, irqstat, base, tmp
- bic \irqnr, \irqstat, #0x1c00
- cmp \irqnr, #16
- strcc \irqstat, [\base, #GIC_CPU_EOI]
- cmpcs \irqnr, \irqnr
- .endm
-
exynos4 has a full copy of entry-macro-gic.S, just for the sake of an offset added to the IRQ number read from the GIC. Add a compute_irqnr macro to entry-macro-gic.S so that any platform can add it's own hook without having to copy the whole file again. Cc: Ben Dooks <ben-linux@fluff.org> Cc: Kukjin Kim <kgene.kim@samsung.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> --- arch/arm/include/asm/hardware/entry-macro-gic.S | 3 + arch/arm/mach-exynos4/include/mach/entry-macro.S | 60 ++-------------------- 2 files changed, 8 insertions(+), 55 deletions(-)