@@ -31,6 +31,14 @@
#define SDHCI_VENDOR_SPEC 0xC0
#define SDHCI_VENDOR_SPEC_SDIO_QUIRK 0x00000002
+/*
+ * There is INT DMA ERR mis-match between eSDHC and STD SDHC SPEC
+ * Bit25 is used in STD SPEC, and is reserved in fsl eSDHC design,
+ * but bit28 is used as the INT DMA ERR in fsl eSDHC design.
+ * Define this macro DMA error INT for fsl eSDHC
+ */
+#define SDHCI_INT_VENDOR_SPEC_DMA_ERR 0x10000000
+
#define ESDHC_FLAG_GPIO_FOR_CD_WP (1 << 0)
/*
* The CMDTYPE of the CMD register (offset 0xE) should be set to
@@ -80,6 +88,20 @@ static u32 esdhc_readl_le(struct sdhci_host *host, int reg)
val |= SDHCI_CARD_PRESENT;
}
+ if (unlikely(reg == SDHCI_CAPABILITIES)) {
+ if (val & SDHCI_CAN_DO_ADMA1) {
+ val &= ~SDHCI_CAN_DO_ADMA1;
+ val |= SDHCI_CAN_DO_ADMA2;
+ }
+ }
+
+ if (unlikely(reg == SDHCI_INT_STATUS)) {
+ if (val & SDHCI_INT_VENDOR_SPEC_DMA_ERR) {
+ val &= ~SDHCI_INT_VENDOR_SPEC_DMA_ERR;
+ val |= SDHCI_INT_ADMA_ERROR;
+ }
+ }
+
return val;
}
@@ -105,6 +127,13 @@ static void esdhc_writel_le(struct sdhci_host *host, u32 val, int reg)
writel(v, host->ioaddr + SDHCI_VENDOR_SPEC);
}
+ if (unlikely((reg == SDHCI_INT_ENABLE)
+ || (reg == SDHCI_SIGNAL_ENABLE))) {
+ if (val & SDHCI_INT_ADMA_ERROR) {
+ val &= ~SDHCI_INT_ADMA_ERROR;
+ val |= SDHCI_INT_VENDOR_SPEC_DMA_ERR;
+ }
+ }
writel(val, host->ioaddr + reg);
}
@@ -322,9 +351,10 @@ static void esdhc_pltfm_exit(struct sdhci_host *host)
}
struct sdhci_pltfm_data sdhci_esdhc_imx_pdata = {
- .quirks = ESDHC_DEFAULT_QUIRKS | SDHCI_QUIRK_BROKEN_ADMA
+ .quirks = ESDHC_DEFAULT_QUIRKS | SDHCI_QUIRK_NO_HISPD_BIT
+ | SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC
+ | SDHCI_QUIRK_BROKEN_ADMA_ZEROLEN_DESC
| SDHCI_QUIRK_BROKEN_CARD_DETECTION,
- /* ADMA has issues. Might be fixable */
.ops = &sdhci_esdhc_ops,
.init = esdhc_pltfm_init,
.exit = esdhc_pltfm_exit,
Eanble the ADMA2 mode on freescale esdhc imx driver, tested on MX51 and MX53. Only ADMA2 mode is enabled, MX25/35 can't support the ADMA2 mode. So this patch is only used for MX51/53. The ADMA2 mode supported or not can be distinguished by the Capability Register(offset 0x40) of eSDHC module. Up to now, only MX51/MX53 set the ADMA2 supported bit(Bit20) in the Capability Register. Signed-off-by: Richard Zhu <richard.zhu@linaro.org> --- drivers/mmc/host/sdhci-esdhc-imx.c | 34 ++++++++++++++++++++++++++++++++-- 1 files changed, 32 insertions(+), 2 deletions(-)