@@ -192,6 +192,16 @@ config DA850_UI_RMII
endchoice
+config DA850_WL12XX
+ bool "AM18x wl1271 daughter board"
+ depends on MACH_DAVINCI_DA850_EVM
+ help
+ The wl1271 daughter card for AM18x EVMs is a combo wireless
+ connectivity add-on card, based on the LS Research TiWi module with
+ Texas Instruments' wl1271 solution.
+ Say Y if you want to use a wl1271 expansion card connected to the
+ AM18x EVM.
+
config GPIO_PCA953X
default MACH_DAVINCI_DA850_EVM
@@ -31,6 +31,8 @@
#include <linux/input/tps6507x-ts.h>
#include <linux/spi/spi.h>
#include <linux/spi/flash.h>
+#include <linux/delay.h>
+#include <linux/wl12xx.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
@@ -49,6 +51,9 @@
#define DA850_MMCSD_CD_PIN GPIO_TO_PIN(4, 0)
#define DA850_MMCSD_WP_PIN GPIO_TO_PIN(4, 1)
+#define DA850_WLAN_EN GPIO_TO_PIN(6, 9)
+#define DA850_WLAN_IRQ GPIO_TO_PIN(6, 10)
+
#define DA850_MII_MDIO_CLKEN_PIN GPIO_TO_PIN(2, 6)
static struct mtd_partition da850evm_spiflash_part[] = {
@@ -1117,6 +1122,110 @@ static __init int da850_evm_init_cpufreq(void)
static __init int da850_evm_init_cpufreq(void) { return 0; }
#endif
+#ifdef CONFIG_DA850_WL12XX
+
+static void wl12xx_set_power(int index, bool power_on)
+{
+ static bool power_state;
+
+ pr_debug("Powering %s wl12xx", power_on ? "on" : "off");
+
+ if (power_on == power_state)
+ return;
+ power_state = power_on;
+
+ if (power_on) {
+ /* Power up sequence required for wl127x devices */
+ gpio_set_value(DA850_WLAN_EN, 1);
+ usleep_range(15000, 15000);
+ gpio_set_value(DA850_WLAN_EN, 0);
+ usleep_range(1000, 1000);
+ gpio_set_value(DA850_WLAN_EN, 1);
+ msleep(70);
+ } else {
+ gpio_set_value(DA850_WLAN_EN, 0);
+ }
+}
+
+static struct davinci_mmc_config da850_wl12xx_mmc_config = {
+ .set_power = wl12xx_set_power,
+ .wires = 4,
+ .max_freq = 25000000,
+ .caps = MMC_CAP_4_BIT_DATA | MMC_CAP_NONREMOVABLE |
+ MMC_CAP_POWER_OFF_CARD,
+ .version = MMC_CTLR_VERSION_2,
+};
+
+static const short da850_wl12xx_pins[] __initconst = {
+ DA850_MMCSD1_DAT_0, DA850_MMCSD1_DAT_1, DA850_MMCSD1_DAT_2,
+ DA850_MMCSD1_DAT_3, DA850_MMCSD1_CLK, DA850_MMCSD1_CMD,
+ DA850_GPIO6_9, DA850_GPIO6_10,
+ -1
+};
+
+static struct wl12xx_platform_data da850_wl12xx_wlan_data __initdata = {
+ .irq = -1,
+ .board_ref_clock = WL12XX_REFCLOCK_38,
+ .platform_quirks = WL12XX_PLATFORM_QUIRK_EDGE_IRQ,
+};
+
+static __init int da850_wl12xx_init(void)
+{
+ int ret;
+
+ ret = davinci_cfg_reg_list(da850_wl12xx_pins);
+ if (ret) {
+ pr_err("wl12xx/mmc mux setup failed: %d\n", ret);
+ goto exit;
+ }
+
+ ret = da850_register_mmcsd1(&da850_wl12xx_mmc_config);
+ if (ret) {
+ pr_err("wl12xx/mmc registration failed: %d\n", ret);
+ goto exit;
+ }
+
+ ret = gpio_request_one(DA850_WLAN_EN, GPIOF_OUT_INIT_LOW, "wl12xx_en");
+ if (ret) {
+ pr_err("Could not request wl12xx enable gpio: %d\n", ret);
+ goto exit;
+ }
+
+ ret = gpio_request_one(DA850_WLAN_IRQ, GPIOF_IN, "wl12xx_irq");
+ if (ret) {
+ pr_err("Could not request wl12xx irq gpio: %d\n", ret);
+ goto free_wlan_en;
+ }
+
+ da850_wl12xx_wlan_data.irq = gpio_to_irq(DA850_WLAN_IRQ);
+
+ ret = wl12xx_set_platform_data(&da850_wl12xx_wlan_data);
+ if (ret) {
+ pr_err("Could not set wl12xx data: %d\n", ret);
+ goto free_wlan_irq;
+ }
+
+ return 0;
+
+free_wlan_irq:
+ gpio_free(DA850_WLAN_IRQ);
+
+free_wlan_en:
+ gpio_free(DA850_WLAN_EN);
+
+exit:
+ return ret;
+}
+
+#else /* CONFIG_DA850_WL12XX */
+
+static __init int da850_wl12xx_init(void)
+{
+ return 0;
+}
+
+#endif /* CONFIG_DA850_WL12XX */
+
#define DA850EVM_SATA_REFCLKPN_RATE (100 * 1000 * 1000)
static __init void da850_evm_init(void)
@@ -1171,6 +1280,11 @@ static __init void da850_evm_init(void)
if (ret)
pr_warning("da850_evm_init: mmcsd0 registration failed:"
" %d\n", ret);
+
+ ret = da850_wl12xx_init();
+ if (ret)
+ pr_warning("da850_evm_init: wl12xx initialization"
+ " failed: %d\n", ret);
}
davinci_serial_init(&da850_evm_uart_config);
The wl1271 daughter card for AM18x EVMs is a combo wireless connectivity add-on card, based on the LS Research TiWi module with Texas Instruments' wl1271 solution. It is a 4-wire, 1.8V, embedded SDIO WLAN device with an external IRQ line and is power-controlled by a GPIO-based fixed regulator. Add support for the WLAN capabilities of this expansion board. Signed-off-by: Ido Yariv <ido@wizery.com> --- arch/arm/mach-davinci/Kconfig | 10 +++ arch/arm/mach-davinci/board-da850-evm.c | 114 +++++++++++++++++++++++++++++++ 2 files changed, 124 insertions(+), 0 deletions(-)