@@ -288,5 +288,6 @@ config MACH_WLF_CRAGG_6410
select S3C_DEV_RTC
select S3C64XX_DEV_SPI
select S3C24XX_GPIO_EXTRA128
+ select I2C
help
Machine support for the Wolfson Cragganmore S3C6410 variant.
@@ -55,7 +55,7 @@ obj-$(CONFIG_MACH_HMT) += mach-hmt.o
obj-$(CONFIG_MACH_SMARTQ) += mach-smartq.o
obj-$(CONFIG_MACH_SMARTQ5) += mach-smartq5.o
obj-$(CONFIG_MACH_SMARTQ7) += mach-smartq7.o
-obj-$(CONFIG_MACH_WLF_CRAGG_6410) += mach-crag6410.o
+obj-$(CONFIG_MACH_WLF_CRAGG_6410) += mach-crag6410.o mach-crag6410-module.o
# device support
new file mode 100644
@@ -0,0 +1,23 @@
+/* Cragganmore 6410 shared definitions
+ *
+ * Copyright 2011 Wolfson Microelectronics plc
+ * Mark Brown <broonie@opensource.wolfsonmicro.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef MACH_CRAG6410_H
+#define MACH_CRAG6410_H
+
+#include <linux/gpio.h>
+
+#define BANFF_PMIC_IRQ_BASE IRQ_BOARD_START
+#define GLENFARCLAS_PMIC_IRQ_BASE (IRQ_BOARD_START + 64)
+
+#define PCA935X_GPIO_BASE GPIO_BOARD_START
+#define CODEC_GPIO_BASE (GPIO_BOARD_START + 8)
+#define GLENFARCLAS_PMIC_GPIO_BASE (GPIO_BOARD_START + 16)
+
+#endif
new file mode 100644
@@ -0,0 +1,167 @@
+/* Speyside modules for Cragganmore - board data probing
+ *
+ * Copyright 2011 Wolfson Microelectronics plc
+ * Mark Brown <broonie@opensource.wolfsonmicro.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/module.h>
+#include <linux/interrupt.h>
+#include <linux/i2c.h>
+
+#include <linux/mfd/wm831x/irq.h>
+#include <linux/mfd/wm831x/gpio.h>
+
+#include <sound/wm8996.h>
+#include <sound/wm8962.h>
+#include <sound/wm9081.h>
+
+#include <mach/crag6410.h>
+
+static struct wm8996_retune_mobile_config wm8996_retune[] = {
+ {
+ .name = "Sub LPF",
+ .rate = 48000,
+ .regs = {
+ 0x6318, 0x6300, 0x1000, 0x0000, 0x0004, 0x2000, 0xF000,
+ 0x0000, 0x0004, 0x2000, 0xF000, 0x0000, 0x0004, 0x2000,
+ 0xF000, 0x0000, 0x0004, 0x1000, 0x0800, 0x4000
+ },
+ },
+ {
+ .name = "Sub HPF",
+ .rate = 48000,
+ .regs = {
+ 0x000A, 0x6300, 0x1000, 0x0000, 0x0004, 0x2000, 0xF000,
+ 0x0000, 0x0004, 0x2000, 0xF000, 0x0000, 0x0004, 0x2000,
+ 0xF000, 0x0000, 0x0004, 0x1000, 0x0800, 0x4000
+ },
+ },
+};
+
+static struct wm8996_pdata wm8996_pdata __initdata = {
+ .ldo_ena = S3C64XX_GPN(7),
+ .gpio_base = CODEC_GPIO_BASE,
+ .micdet_def = 1,
+ .inl_mode = WM8996_DIFFERRENTIAL_1,
+ .inr_mode = WM8996_DIFFERRENTIAL_1,
+
+ .irq_flags = IRQF_TRIGGER_RISING,
+
+ .gpio_default = {
+ 0x8001, /* GPIO1 == ADCLRCLK1 */
+ 0x8001, /* GPIO2 == ADCLRCLK2, input due to CPU */
+ 0x0141, /* GPIO3 == HP_SEL */
+ 0x0002, /* GPIO4 == IRQ */
+ 0x020e, /* GPIO5 == CLKOUT */
+ },
+
+ .retune_mobile_cfgs = wm8996_retune,
+ .num_retune_mobile_cfgs = ARRAY_SIZE(wm8996_retune),
+};
+
+static struct wm8962_pdata wm8962_pdata __initdata = {
+ .gpio_init = {
+ 0,
+ WM8962_GPIO_FN_OPCLK,
+ WM8962_GPIO_FN_DMICCLK,
+ 0,
+ 0x8000 | WM8962_GPIO_FN_DMICDAT,
+ WM8962_GPIO_FN_IRQ, /* Open drain mode */
+ },
+ .irq_active_low = true,
+};
+
+static struct wm9081_pdata wm9081_pdata __initdata = {
+ .irq_high = false,
+ .irq_cmos = false,
+};
+
+static const struct i2c_board_info wm1254_devs[] = {
+ { I2C_BOARD_INFO("wm8996", 0x1a),
+ .platform_data = &wm8996_pdata,
+ .irq = GLENFARCLAS_PMIC_IRQ_BASE + WM831X_IRQ_GPIO_2,
+ },
+ { I2C_BOARD_INFO("wm9081", 0x6c),
+ .platform_data = &wm9081_pdata, },
+};
+
+static const struct i2c_board_info wm1259_devs[] = {
+ { I2C_BOARD_INFO("wm8962", 0x1a),
+ .platform_data = &wm8962_pdata,
+ .irq = GLENFARCLAS_PMIC_IRQ_BASE + WM831X_IRQ_GPIO_2,
+ },
+};
+
+
+static const struct {
+ u8 id;
+ const char *name;
+ const struct i2c_board_info *i2c_devs;
+ int num_i2c_devs;
+} gf_mods[] = {
+ { .id = 0x11, .name = "6249-EV2 Glenfarclas", },
+ { .id = 0x31, .name = "1253-EV1 Tomatin", },
+ { .id = 0x39, .name = "1254-EV1 Dallas Dhu",
+ .i2c_devs = wm1254_devs, .num_i2c_devs = ARRAY_SIZE(wm1254_devs) },
+ { .id = 0x3a, .name = "1259-EV1 Tobermory",
+ .i2c_devs = wm1259_devs, .num_i2c_devs = ARRAY_SIZE(wm1259_devs) },
+ { .id = 0x3b, .name = "1255-EV1 Kilchoman" },
+};
+
+static __devinit int wlf_gf_module_probe(struct i2c_client *i2c,
+ const struct i2c_device_id *i2c_id)
+{
+ int ret, i, j, id, rev;
+
+ ret = i2c_smbus_read_byte_data(i2c, 0);
+ if (ret < 0) {
+ dev_err(&i2c->dev, "Failed to read ID: %d\n", ret);
+ return ret;
+ }
+
+ id = (ret & 0xfe) >> 2;
+ rev = ret & 0x3;
+ for (i = 0; i < ARRAY_SIZE(gf_mods); i++)
+ if (id == gf_mods[i].id)
+ break;
+
+ if (i < ARRAY_SIZE(gf_mods)) {
+ dev_info(&i2c->dev, "%s revision %d\n",
+ gf_mods[i].name, rev + 1);
+ for (j = 0; j < gf_mods[i].num_i2c_devs; j++) {
+ if (!i2c_new_device(i2c->adapter,
+ &(gf_mods[i].i2c_devs[j])))
+ dev_err(&i2c->dev,
+ "Failed to register dev: %d\n", ret);
+ }
+ } else {
+ dev_warn(&i2c->dev, "Unknown module ID %d revision %d\n",
+ id, rev);
+ }
+
+ return 0;
+}
+
+static const struct i2c_device_id wlf_gf_module_id[] = {
+ { "wlf-gf-module", 0 },
+ { }
+};
+
+static struct i2c_driver wlf_gf_module = {
+ .driver = {
+ .name = "wlf-gf-module",
+ .owner = THIS_MODULE,
+ },
+ .probe = wlf_gf_module_probe,
+ .id_table = wlf_gf_module_id,
+};
+
+static int __init wlf_gf_module_register(void)
+{
+ return i2c_add_driver(&wlf_gf_module);
+}
+module_init(wlf_gf_module_register);
@@ -47,6 +47,7 @@
#include <mach/regs-sys.h>
#include <mach/regs-gpio.h>
#include <mach/regs-modem.h>
+#include <mach/crag6410.h>
#include <mach/regs-gpio-memport.h>
@@ -65,17 +66,6 @@
#include <plat/iic.h>
#include <plat/pm.h>
-#include <sound/wm8996.h>
-#include <sound/wm8962.h>
-#include <sound/wm9081.h>
-
-#define BANFF_PMIC_IRQ_BASE IRQ_BOARD_START
-#define GLENFARCLAS_PMIC_IRQ_BASE (IRQ_BOARD_START + 64)
-
-#define PCA935X_GPIO_BASE GPIO_BOARD_START
-#define CODEC_GPIO_BASE (GPIO_BOARD_START + 8)
-#define GLENFARCLAS_PMIC_GPIO_BASE (GPIO_BOARD_START + 16)
-
/* serial port setup */
#define UCON (S3C2410_UCON_DEFAULT | S3C2410_UCON_UCLK)
@@ -623,81 +613,16 @@ static struct wm831x_pdata glenfarclas_pmic_pdata __initdata = {
.disable_touch = true,
};
-static struct wm8996_retune_mobile_config wm8996_retune[] = {
- {
- .name = "Sub LPF",
- .rate = 48000,
- .regs = {
- 0x6318, 0x6300, 0x1000, 0x0000, 0x0004, 0x2000, 0xF000,
- 0x0000, 0x0004, 0x2000, 0xF000, 0x0000, 0x0004, 0x2000,
- 0xF000, 0x0000, 0x0004, 0x1000, 0x0800, 0x4000
- },
- },
- {
- .name = "Sub HPF",
- .rate = 48000,
- .regs = {
- 0x000A, 0x6300, 0x1000, 0x0000, 0x0004, 0x2000, 0xF000,
- 0x0000, 0x0004, 0x2000, 0xF000, 0x0000, 0x0004, 0x2000,
- 0xF000, 0x0000, 0x0004, 0x1000, 0x0800, 0x4000
- },
- },
-};
-
-static struct wm8996_pdata wm8996_pdata __initdata = {
- .ldo_ena = S3C64XX_GPN(7),
- .gpio_base = CODEC_GPIO_BASE,
- .micdet_def = 1,
- .inl_mode = WM8996_DIFFERRENTIAL_1,
- .inr_mode = WM8996_DIFFERRENTIAL_1,
-
- .irq_flags = IRQF_TRIGGER_RISING,
-
- .gpio_default = {
- 0x8001, /* GPIO1 == ADCLRCLK1 */
- 0x8001, /* GPIO2 == ADCLRCLK2, input due to CPU */
- 0x0141, /* GPIO3 == HP_SEL */
- 0x0002, /* GPIO4 == IRQ */
- 0x020e, /* GPIO5 == CLKOUT */
- },
-
- .retune_mobile_cfgs = wm8996_retune,
- .num_retune_mobile_cfgs = ARRAY_SIZE(wm8996_retune),
-};
-
-static struct wm8962_pdata wm8962_pdata __initdata = {
- .gpio_init = {
- 0,
- WM8962_GPIO_FN_OPCLK,
- WM8962_GPIO_FN_DMICCLK,
- 0,
- 0x8000 | WM8962_GPIO_FN_DMICDAT,
- WM8962_GPIO_FN_IRQ, /* Open drain mode */
- },
- .irq_active_low = true,
-};
-
-static struct wm9081_pdata wm9081_pdata __initdata = {
- .irq_high = false,
- .irq_cmos = false,
-};
-
static struct i2c_board_info i2c_devs1[] __initdata = {
{ I2C_BOARD_INFO("wm8311", 0x34),
.irq = S3C_EINT(0),
.platform_data = &glenfarclas_pmic_pdata },
+ { I2C_BOARD_INFO("wlf-gf-module", 0x24) },
+ { I2C_BOARD_INFO("wlf-gf-module", 0x25) },
+ { I2C_BOARD_INFO("wlf-gf-module", 0x26) },
+
{ I2C_BOARD_INFO("wm1250-ev1", 0x27) },
- { I2C_BOARD_INFO("wm8996", 0x1a),
- .platform_data = &wm8996_pdata,
- .irq = GLENFARCLAS_PMIC_IRQ_BASE + WM831X_IRQ_GPIO_2,
- },
- { I2C_BOARD_INFO("wm9081", 0x6c),
- .platform_data = &wm9081_pdata, },
- { I2C_BOARD_INFO("wm8962", 0x1a),
- .platform_data = &wm8962_pdata,
- .irq = GLENFARCLAS_PMIC_IRQ_BASE + WM831X_IRQ_GPIO_2,
- },
};
static void __init crag6410_map_io(void)
The Cragganmore system is modular with I2C based identification chips on the system allowing identification of the system build. Provide a stub I2C driver which parses the module IDs and uses them to select the appropriate audio subsystem components to register. To avoid confusion due to having the mini-driver in the system the driver is placed in a separate file. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> --- Sorry, resent due to a line of context from a change that is not yet upstreamed which would cause an issue applying the change. arch/arm/mach-s3c64xx/Kconfig | 1 + arch/arm/mach-s3c64xx/Makefile | 2 +- arch/arm/mach-s3c64xx/include/mach/crag6410.h | 23 ++++ arch/arm/mach-s3c64xx/mach-crag6410-module.c | 167 +++++++++++++++++++++++++ arch/arm/mach-s3c64xx/mach-crag6410.c | 85 +------------ 5 files changed, 197 insertions(+), 81 deletions(-) create mode 100644 arch/arm/mach-s3c64xx/include/mach/crag6410.h create mode 100644 arch/arm/mach-s3c64xx/mach-crag6410-module.c