| Message ID | 1341385499-5781-1-git-send-email-jiri.prchal@aksignal.cz (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
HI, please put a correct title of the commit On 09:04 Wed 04 Jul , Jiri Prchal wrote: > I'd like to add support for our "CDU" board based up on Telit's module GE863 Pro3. > It has more uarts, leds, another nand partitioning. > > Signed-off-by: Jiri Prchal <jiri.prchal@aksignal.cz> > --- > arch/arm/boot/dts/aks-cdu.dts | 111 +++++++++++++++++++++++++++++++++++++++++ plewase update thei arch/arm/mach-at91/Makefile.boot Best Regards, J. > 1 files changed, 111 insertions(+), 0 deletions(-) > create mode 100644 arch/arm/boot/dts/aks-cdu.dts > > diff --git a/arch/arm/boot/dts/aks-cdu.dts b/arch/arm/boot/dts/aks-cdu.dts > new file mode 100644 > index 0000000..05590cc > --- /dev/null > +++ b/arch/arm/boot/dts/aks-cdu.dts > @@ -0,0 +1,111 @@ > +/* > + * aks-cdu.dts - Device Tree file for AK signal CDU > + * > + * Copyright (C) 2012 AK signal Brno a.s. > + * 2012 Jiri Prchal <jiri.prchal@aksignal.cz> > + * > + * Licensed under GPLv2 or later. > + */ > + > +/include/ "ge863-pro3.dtsi" > + > +/ { > + chosen { > + bootargs = "console=ttyS0,115200 ubi.mtd=4 root=ubi0:rootfs rootfstype=ubifs"; > + }; > + > + ahb { > + apb { > + usart0: serial@fffb0000 { > + status = "okay"; > + }; > + > + usart1: serial@fffb4000 { > + status = "okay"; > + linux,rs485-enabled-at-boot-time; > + rs485-rts-delay = <0 0>; > + }; > + > + usart2: serial@fffb8000 { > + status = "okay"; > + linux,rs485-enabled-at-boot-time; > + rs485-rts-delay = <0 0>; > + }; > + > + usart3: serial@fffd0000 { > + status = "okay"; > + linux,rs485-enabled-at-boot-time; > + rs485-rts-delay = <0 0>; > + }; > + > + macb0: ethernet@fffbc000 { > + phy-mode = "rmii"; > + status = "okay"; > + }; > + > + usb1: gadget@fffa4000 { > + atmel,vbus-gpio = <&pioC 15 0>; > + status = "okay"; > + }; > + }; > + > + usb0: ohci@00500000 { > + num-ports = <2>; > + status = "okay"; > + }; > + > + nand0: nand@40000000 { > + nand-bus-width = <8>; > + nand-ecc-mode = "soft"; > + nand-on-flash-bbt; > + status = "okay"; > + > + bootstrap@0 { > + label = "bootstrap"; > + reg = <0x0 0x40000>; > + }; > + > + uboot@40000 { > + label = "uboot"; > + reg = <0x40000 0x80000>; > + }; > + ubootenv@c0000 { > + label = "ubootenv"; > + reg = <0xc0000 0x40000>; > + }; > + kernel@100000 { > + label = "kernel"; > + reg = <0x100000 0x400000>; > + }; > + rootfs@500000 { > + label = "rootfs"; > + reg = <0x500000 0x7b00000>; > + }; > + }; > + }; > + > + leds { > + compatible = "gpio-leds"; > + > + red { > + gpios = <&pioC 10 0>; > + linux,default-trigger = "none"; > + }; > + > + green { > + gpios = <&pioA 5 1>; > + linux,default-trigger = "none"; > + default-state = "on"; > + }; > + > + yellow { > + gpios = <&pioB 20 1>; > + linux,default-trigger = "none"; > + }; > + > + blue { > + gpios = <&pioB 21 1>; > + linux,default-trigger = "none"; > + }; > + }; > +}; > -- > 1.7.7 >
diff --git a/arch/arm/boot/dts/aks-cdu.dts b/arch/arm/boot/dts/aks-cdu.dts new file mode 100644 index 0000000..05590cc --- /dev/null +++ b/arch/arm/boot/dts/aks-cdu.dts @@ -0,0 +1,111 @@ +/* + * aks-cdu.dts - Device Tree file for AK signal CDU + * + * Copyright (C) 2012 AK signal Brno a.s. + * 2012 Jiri Prchal <jiri.prchal@aksignal.cz> + * + * Licensed under GPLv2 or later. + */ + +/include/ "ge863-pro3.dtsi" + +/ { + chosen { + bootargs = "console=ttyS0,115200 ubi.mtd=4 root=ubi0:rootfs rootfstype=ubifs"; + }; + + ahb { + apb { + usart0: serial@fffb0000 { + status = "okay"; + }; + + usart1: serial@fffb4000 { + status = "okay"; + linux,rs485-enabled-at-boot-time; + rs485-rts-delay = <0 0>; + }; + + usart2: serial@fffb8000 { + status = "okay"; + linux,rs485-enabled-at-boot-time; + rs485-rts-delay = <0 0>; + }; + + usart3: serial@fffd0000 { + status = "okay"; + linux,rs485-enabled-at-boot-time; + rs485-rts-delay = <0 0>; + }; + + macb0: ethernet@fffbc000 { + phy-mode = "rmii"; + status = "okay"; + }; + + usb1: gadget@fffa4000 { + atmel,vbus-gpio = <&pioC 15 0>; + status = "okay"; + }; + }; + + usb0: ohci@00500000 { + num-ports = <2>; + status = "okay"; + }; + + nand0: nand@40000000 { + nand-bus-width = <8>; + nand-ecc-mode = "soft"; + nand-on-flash-bbt; + status = "okay"; + + bootstrap@0 { + label = "bootstrap"; + reg = <0x0 0x40000>; + }; + + uboot@40000 { + label = "uboot"; + reg = <0x40000 0x80000>; + }; + ubootenv@c0000 { + label = "ubootenv"; + reg = <0xc0000 0x40000>; + }; + kernel@100000 { + label = "kernel"; + reg = <0x100000 0x400000>; + }; + rootfs@500000 { + label = "rootfs"; + reg = <0x500000 0x7b00000>; + }; + }; + }; + + leds { + compatible = "gpio-leds"; + + red { + gpios = <&pioC 10 0>; + linux,default-trigger = "none"; + }; + + green { + gpios = <&pioA 5 1>; + linux,default-trigger = "none"; + default-state = "on"; + }; + + yellow { + gpios = <&pioB 20 1>; + linux,default-trigger = "none"; + }; + + blue { + gpios = <&pioB 21 1>; + linux,default-trigger = "none"; + }; + }; +};
I'd like to add support for our "CDU" board based up on Telit's module GE863 Pro3. It has more uarts, leds, another nand partitioning. Signed-off-by: Jiri Prchal <jiri.prchal@aksignal.cz> --- arch/arm/boot/dts/aks-cdu.dts | 111 +++++++++++++++++++++++++++++++++++++++++ 1 files changed, 111 insertions(+), 0 deletions(-) create mode 100644 arch/arm/boot/dts/aks-cdu.dts