diff mbox

ARM: at91: Add support for board aks-cdu

Message ID 1341821118-8177-1-git-send-email-jiri.prchal@aksignal.cz (mailing list archive)
State New, archived
Headers show

Commit Message

Jiri Prchal July 9, 2012, 8:05 a.m. UTC 
Add support for our "aks-cdu" board based up on Telit's module GE863 Pro3.
It has more uarts, leds, another nand partitioning.

Signed-off-by: Jiri Prchal <jiri.prchal@aksignal.cz>
---
 arch/arm/boot/dts/aks-cdu.dts    |  111 ++++++++++++++++++++++++++++++++++++++
 arch/arm/mach-at91/Makefile.boot |    1 +
 2 files changed, 112 insertions(+), 0 deletions(-)
 create mode 100644 arch/arm/boot/dts/aks-cdu.dts

Comments

Nicolas Ferre July 9, 2012, 6:54 p.m. UTC | #1 
On 07/09/2012 10:05 AM, Jiri Prchal :
> Add support for our "aks-cdu" board based up on Telit's module GE863 Pro3.
> It has more uarts, leds, another nand partitioning.
> 
> Signed-off-by: Jiri Prchal <jiri.prchal@aksignal.cz>
> ---
>  arch/arm/boot/dts/aks-cdu.dts    |  111 ++++++++++++++++++++++++++++++++++++++
>  arch/arm/mach-at91/Makefile.boot |    1 +
>  2 files changed, 112 insertions(+), 0 deletions(-)
>  create mode 100644 arch/arm/boot/dts/aks-cdu.dts
> 
> diff --git a/arch/arm/boot/dts/aks-cdu.dts b/arch/arm/boot/dts/aks-cdu.dts
> new file mode 100644
> index 0000000..05590cc
> --- /dev/null
> +++ b/arch/arm/boot/dts/aks-cdu.dts
> @@ -0,0 +1,111 @@
> +/*
> + * aks-cdu.dts - Device Tree file for AK signal CDU
> + *
> + * Copyright (C) 2012 AK signal Brno a.s.
> + *               2012 Jiri Prchal <jiri.prchal@aksignal.cz>
> + *
> + * Licensed under GPLv2 or later.
> + */
> + 

This:

/dts-v1/;

is missing: I cannot compile the .dts


> +/include/ "ge863-pro3.dtsi"
> +
> +/ {
> +	chosen {
> +		bootargs = "console=ttyS0,115200 ubi.mtd=4 root=ubi0:rootfs rootfstype=ubifs";
> +	};
> +
> +	ahb {
> +		apb {
> +			usart0: serial@fffb0000 {
> +				status = "okay";
> +			};
> +
> +			usart1: serial@fffb4000 {
> +				status = "okay";
> +				linux,rs485-enabled-at-boot-time;
> +				rs485-rts-delay = <0 0>;
> +				};
> +
> +			usart2: serial@fffb8000 {
> +				status = "okay";
> +				linux,rs485-enabled-at-boot-time;
> +				rs485-rts-delay = <0 0>;
> +			};
> +
> +			usart3: serial@fffd0000 {
> +				status = "okay";
> +				linux,rs485-enabled-at-boot-time;
> +				rs485-rts-delay = <0 0>;
> +			};
> +
> +			macb0: ethernet@fffbc000 {

This is wrong: it can compile better with that:

                       macb0: ethernet@fffc4000 {

if you board is based on an at91sam9260, it is the proper address of the
EMAC.

> +				phy-mode = "rmii";
> +				status = "okay";
> +			};
> +
> +			usb1: gadget@fffa4000 {
> +				atmel,vbus-gpio = <&pioC 15 0>;
> +				status = "okay";
> +			};
> +		};
> +
> +		usb0: ohci@00500000 {
> +			num-ports = <2>;
> +			status = "okay";
> +		};
> +
> +		nand0: nand@40000000 {
> +			nand-bus-width = <8>;
> +			nand-ecc-mode = "soft";
> +			nand-on-flash-bbt;
> +			status = "okay";
> +
> +			bootstrap@0 {
> +				label = "bootstrap";
> +				reg = <0x0 0x40000>;
> +			};
> +
> +			uboot@40000 {
> +				label = "uboot";
> +				reg = <0x40000 0x80000>;
> +			};
> +			ubootenv@c0000 {
> +				label = "ubootenv";
> +				reg = <0xc0000 0x40000>;
> +			};
> +			kernel@100000 {
> +				label = "kernel";
> +				reg = <0x100000 0x400000>;
> +			};
> +			rootfs@500000 {
> +				label = "rootfs";
> +				reg = <0x500000 0x7b00000>;
> +			};
> +		};
> +	};
> +
> +	leds {
> +		compatible = "gpio-leds";
> +
> +		red {
> +			gpios = <&pioC 10 0>;
> +			linux,default-trigger = "none";
> +		};
> +
> +		green {
> +			gpios = <&pioA 5 1>;
> +			linux,default-trigger = "none";
> +			default-state = "on";
> +		};
> +
> +		yellow {
> +			gpios = <&pioB 20 1>;
> +			linux,default-trigger = "none";
> +		};
> +
> +		blue {
> +			gpios = <&pioB 21 1>;
> +			linux,default-trigger = "none";
> +		};
> +	};
> +};
> diff --git a/arch/arm/mach-at91/Makefile.boot b/arch/arm/mach-at91/Makefile.boot
> index 11c3ca7..30bb733 100644
> --- a/arch/arm/mach-at91/Makefile.boot
> +++ b/arch/arm/mach-at91/Makefile.boot
> @@ -15,6 +15,7 @@ endif
>  
>  # Keep dtb files sorted alphabetically for each SoC
>  # sam9260
> +dtb-$(CONFIG_MACH_AT91SAM_DT) += aks-cdu.dtb
>  dtb-$(CONFIG_MACH_AT91SAM_DT) += ethernut5.dtb
>  dtb-$(CONFIG_MACH_AT91SAM_DT) += evk-pro3.dtb
>  dtb-$(CONFIG_MACH_AT91SAM_DT) += tny_a9260.dtb


Please use

make ARCH=arm CROSS_COMPILE=arm-linux-gnueabi- aks-cdu.dtb
or
make ARCH=arm CROSS_COMPILE=arm-linux-gnueabi- dtbs

So that you can check that your device tree file is correct.

Anyway, I have added the corrections and pushed this patch in the AT91
at91-3.6-dt branch.

Thanks, best regards,
diff mbox

Patch

diff --git a/arch/arm/boot/dts/aks-cdu.dts b/arch/arm/boot/dts/aks-cdu.dts
new file mode 100644
index 0000000..05590cc
--- /dev/null
+++ b/arch/arm/boot/dts/aks-cdu.dts
@@ -0,0 +1,111 @@ 
+/*
+ * aks-cdu.dts - Device Tree file for AK signal CDU
+ *
+ * Copyright (C) 2012 AK signal Brno a.s.
+ *               2012 Jiri Prchal <jiri.prchal@aksignal.cz>
+ *
+ * Licensed under GPLv2 or later.
+ */
+
+/include/ "ge863-pro3.dtsi"
+
+/ {
+	chosen {
+		bootargs = "console=ttyS0,115200 ubi.mtd=4 root=ubi0:rootfs rootfstype=ubifs";
+	};
+
+	ahb {
+		apb {
+			usart0: serial@fffb0000 {
+				status = "okay";
+			};
+
+			usart1: serial@fffb4000 {
+				status = "okay";
+				linux,rs485-enabled-at-boot-time;
+				rs485-rts-delay = <0 0>;
+				};
+
+			usart2: serial@fffb8000 {
+				status = "okay";
+				linux,rs485-enabled-at-boot-time;
+				rs485-rts-delay = <0 0>;
+			};
+
+			usart3: serial@fffd0000 {
+				status = "okay";
+				linux,rs485-enabled-at-boot-time;
+				rs485-rts-delay = <0 0>;
+			};
+
+			macb0: ethernet@fffbc000 {
+				phy-mode = "rmii";
+				status = "okay";
+			};
+
+			usb1: gadget@fffa4000 {
+				atmel,vbus-gpio = <&pioC 15 0>;
+				status = "okay";
+			};
+		};
+
+		usb0: ohci@00500000 {
+			num-ports = <2>;
+			status = "okay";
+		};
+
+		nand0: nand@40000000 {
+			nand-bus-width = <8>;
+			nand-ecc-mode = "soft";
+			nand-on-flash-bbt;
+			status = "okay";
+
+			bootstrap@0 {
+				label = "bootstrap";
+				reg = <0x0 0x40000>;
+			};
+
+			uboot@40000 {
+				label = "uboot";
+				reg = <0x40000 0x80000>;
+			};
+			ubootenv@c0000 {
+				label = "ubootenv";
+				reg = <0xc0000 0x40000>;
+			};
+			kernel@100000 {
+				label = "kernel";
+				reg = <0x100000 0x400000>;
+			};
+			rootfs@500000 {
+				label = "rootfs";
+				reg = <0x500000 0x7b00000>;
+			};
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		red {
+			gpios = <&pioC 10 0>;
+			linux,default-trigger = "none";
+		};
+
+		green {
+			gpios = <&pioA 5 1>;
+			linux,default-trigger = "none";
+			default-state = "on";
+		};
+
+		yellow {
+			gpios = <&pioB 20 1>;
+			linux,default-trigger = "none";
+		};
+
+		blue {
+			gpios = <&pioB 21 1>;
+			linux,default-trigger = "none";
+		};
+	};
+};
diff --git a/arch/arm/mach-at91/Makefile.boot b/arch/arm/mach-at91/Makefile.boot
index 11c3ca7..30bb733 100644
--- a/arch/arm/mach-at91/Makefile.boot
+++ b/arch/arm/mach-at91/Makefile.boot
@@ -15,6 +15,7 @@  endif
 
 # Keep dtb files sorted alphabetically for each SoC
 # sam9260
+dtb-$(CONFIG_MACH_AT91SAM_DT) += aks-cdu.dtb
 dtb-$(CONFIG_MACH_AT91SAM_DT) += ethernut5.dtb
 dtb-$(CONFIG_MACH_AT91SAM_DT) += evk-pro3.dtb
 dtb-$(CONFIG_MACH_AT91SAM_DT) += tny_a9260.dtb