diff --git a/arch/arm/mach-imx/efika.h b/arch/arm/mach-imx/efika.h
deleted file mode 100644
index 014aa98..0000000
--- a/arch/arm/mach-imx/efika.h
+++ /dev/null
@@ -1,10 +0,0 @@
-#ifndef _EFIKA_H
-#define _EFIKA_H
-
-#define EFIKA_WLAN_EN		IMX_GPIO_NR(2, 16)
-#define EFIKA_WLAN_RESET	IMX_GPIO_NR(2, 10)
-#define EFIKA_USB_PHY_RESET	IMX_GPIO_NR(2, 9)
-
-void __init efika_board_common_init(void);
-
-#endif
diff --git a/arch/arm/mach-imx/mach-mx51_efikamx.c b/arch/arm/mach-imx/mach-mx51_efikamx.c
deleted file mode 100644
index 8d09c01..0000000
--- a/arch/arm/mach-imx/mach-mx51_efikamx.c
+++ /dev/null
@@ -1,300 +0,0 @@
-/*
- * Copyright (C) 2010 Linaro Limited
- *
- * based on code from the following
- * Copyright 2009-2010 Freescale Semiconductor, Inc. All Rights Reserved.
- * Copyright 2009-2010 Pegatron Corporation. All Rights Reserved.
- * Copyright 2009-2010 Genesi USA, Inc. All Rights Reserved.
- *
- * The code contained herein is licensed under the GNU General Public
- * License. You may obtain a copy of the GNU General Public License
- * Version 2 or later at the following locations:
- *
- * http://www.opensource.org/licenses/gpl-license.html
- * http://www.gnu.org/copyleft/gpl.html
- */
-
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/i2c.h>
-#include <linux/gpio.h>
-#include <linux/leds.h>
-#include <linux/input.h>
-#include <linux/delay.h>
-#include <linux/io.h>
-#include <linux/spi/flash.h>
-#include <linux/spi/spi.h>
-#include <linux/mfd/mc13892.h>
-#include <linux/regulator/machine.h>
-#include <linux/regulator/consumer.h>
-
-#include <mach/common.h>
-#include <mach/hardware.h>
-#include <mach/iomux-mx51.h>
-
-#include <asm/setup.h>
-#include <asm/system_info.h>
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/time.h>
-
-#include "devices-imx51.h"
-#include "efika.h"
-
-#define EFIKAMX_PCBID0		IMX_GPIO_NR(3, 16)
-#define EFIKAMX_PCBID1		IMX_GPIO_NR(3, 17)
-#define EFIKAMX_PCBID2		IMX_GPIO_NR(3, 11)
-
-#define EFIKAMX_BLUE_LED	IMX_GPIO_NR(3, 13)
-#define EFIKAMX_GREEN_LED	IMX_GPIO_NR(3, 14)
-#define EFIKAMX_RED_LED		IMX_GPIO_NR(3, 15)
-
-#define EFIKAMX_POWER_KEY	IMX_GPIO_NR(2, 31)
-
-/* board 1.1 doesn't have same reset gpio */
-#define EFIKAMX_RESET1_1	IMX_GPIO_NR(3, 2)
-#define EFIKAMX_RESET		IMX_GPIO_NR(1, 4)
-
-#define EFIKAMX_POWEROFF	IMX_GPIO_NR(4, 13)
-
-#define EFIKAMX_PMIC		IMX_GPIO_NR(1, 6)
-
-/* the pci ids pin have pull up. they're driven low according to board id */
-#define MX51_PAD_PCBID0	IOMUX_PAD(0x518, 0x130, 3, 0x0,   0, PAD_CTL_PUS_100K_UP)
-#define MX51_PAD_PCBID1	IOMUX_PAD(0x51C, 0x134, 3, 0x0,   0, PAD_CTL_PUS_100K_UP)
-#define MX51_PAD_PCBID2	IOMUX_PAD(0x504, 0x128, 3, 0x0,   0, PAD_CTL_PUS_100K_UP)
-#define MX51_PAD_PWRKEY	IOMUX_PAD(0x48c, 0x0f8, 1, 0x0,   0, PAD_CTL_PUS_100K_UP | PAD_CTL_PKE)
-
-static iomux_v3_cfg_t mx51efikamx_pads[] = {
-	/* board id */
-	MX51_PAD_PCBID0,
-	MX51_PAD_PCBID1,
-	MX51_PAD_PCBID2,
-
-	/* leds */
-	MX51_PAD_CSI1_D9__GPIO3_13,
-	MX51_PAD_CSI1_VSYNC__GPIO3_14,
-	MX51_PAD_CSI1_HSYNC__GPIO3_15,
-
-	/* power key */
-	MX51_PAD_PWRKEY,
-
-	/* reset */
-	MX51_PAD_DI1_PIN13__GPIO3_2,
-	MX51_PAD_GPIO1_4__GPIO1_4,
-
-	/* power off */
-	MX51_PAD_CSI2_VSYNC__GPIO4_13,
-};
-
-/*   PCBID2  PCBID1 PCBID0  STATE
-	1       1      1    ER1:rev1.1
-	1       1      0    ER2:rev1.2
-	1       0      1    ER3:rev1.3
-	1       0      0    ER4:rev1.4
-*/
-static void __init mx51_efikamx_board_id(void)
-{
-	int id;
-
-	/* things are taking time to settle */
-	msleep(150);
-
-	gpio_request(EFIKAMX_PCBID0, "pcbid0");
-	gpio_direction_input(EFIKAMX_PCBID0);
-	gpio_request(EFIKAMX_PCBID1, "pcbid1");
-	gpio_direction_input(EFIKAMX_PCBID1);
-	gpio_request(EFIKAMX_PCBID2, "pcbid2");
-	gpio_direction_input(EFIKAMX_PCBID2);
-
-	id = gpio_get_value(EFIKAMX_PCBID0) ? 1 : 0;
-	id |= (gpio_get_value(EFIKAMX_PCBID1) ? 1 : 0) << 1;
-	id |= (gpio_get_value(EFIKAMX_PCBID2) ? 1 : 0) << 2;
-
-	switch (id) {
-	case 7:
-		system_rev = 0x11;
-		break;
-	case 6:
-		system_rev = 0x12;
-		break;
-	case 5:
-		system_rev = 0x13;
-		break;
-	case 4:
-		system_rev = 0x14;
-		break;
-	default:
-		system_rev = 0x10;
-		break;
-	}
-
-	if ((system_rev == 0x10)
-		|| (system_rev == 0x12)
-		|| (system_rev == 0x14)) {
-		printk(KERN_WARNING
-			"EfikaMX: Unsupported board revision 1.%u!\n",
-			system_rev & 0xf);
-	}
-}
-
-static struct gpio_led mx51_efikamx_leds[] __initdata = {
-	{
-		.name = "efikamx:green",
-		.default_trigger = "default-on",
-		.gpio = EFIKAMX_GREEN_LED,
-	},
-	{
-		.name = "efikamx:red",
-		.default_trigger = "ide-disk",
-		.gpio = EFIKAMX_RED_LED,
-	},
-	{
-		.name = "efikamx:blue",
-		.default_trigger = "mmc0",
-		.gpio = EFIKAMX_BLUE_LED,
-	},
-};
-
-static const struct gpio_led_platform_data
-		mx51_efikamx_leds_data __initconst = {
-	.leds = mx51_efikamx_leds,
-	.num_leds = ARRAY_SIZE(mx51_efikamx_leds),
-};
-
-static struct esdhc_platform_data sd_pdata = {
-	.cd_type = ESDHC_CD_CONTROLLER,
-	.wp_type = ESDHC_WP_CONTROLLER,
-};
-
-static struct gpio_keys_button mx51_efikamx_powerkey[] = {
-	{
-		.code = KEY_POWER,
-		.gpio = EFIKAMX_POWER_KEY,
-		.type = EV_PWR,
-		.desc = "Power Button (CM)",
-		.wakeup = 1,
-		.debounce_interval = 10, /* ms */
-	},
-};
-
-static const struct gpio_keys_platform_data mx51_efikamx_powerkey_data __initconst = {
-	.buttons = mx51_efikamx_powerkey,
-	.nbuttons = ARRAY_SIZE(mx51_efikamx_powerkey),
-};
-
-static void mx51_efikamx_restart(char mode, const char *cmd)
-{
-	if (system_rev == 0x11)
-		gpio_direction_output(EFIKAMX_RESET1_1, 0);
-	else
-		gpio_direction_output(EFIKAMX_RESET, 0);
-}
-
-static struct regulator *pwgt1, *pwgt2, *coincell;
-
-static void mx51_efikamx_power_off(void)
-{
-	if (!IS_ERR(coincell))
-		regulator_disable(coincell);
-
-	if (!IS_ERR(pwgt1) && !IS_ERR(pwgt2)) {
-		regulator_disable(pwgt2);
-		regulator_disable(pwgt1);
-	}
-	gpio_direction_output(EFIKAMX_POWEROFF, 1);
-}
-
-static int __init mx51_efikamx_power_init(void)
-{
-	pwgt1 = regulator_get(NULL, "pwgt1");
-	pwgt2 = regulator_get(NULL, "pwgt2");
-	if (!IS_ERR(pwgt1) && !IS_ERR(pwgt2)) {
-		regulator_enable(pwgt1);
-		regulator_enable(pwgt2);
-	}
-	gpio_request(EFIKAMX_POWEROFF, "poweroff");
-	pm_power_off = mx51_efikamx_power_off;
-
-	/* enable coincell charger. maybe need a small power driver ? */
-	coincell = regulator_get(NULL, "coincell");
-	if (!IS_ERR(coincell)) {
-		regulator_set_voltage(coincell, 3000000, 3000000);
-		regulator_enable(coincell);
-	}
-
-	regulator_has_full_constraints();
-
-	return 0;
-}
-
-static void __init mx51_efikamx_init_late(void)
-{
-	imx51_init_late();
-	mx51_efikamx_power_init();
-}
-
-static void __init mx51_efikamx_init(void)
-{
-	imx51_soc_init();
-
-	mxc_iomux_v3_setup_multiple_pads(mx51efikamx_pads,
-					ARRAY_SIZE(mx51efikamx_pads));
-	efika_board_common_init();
-
-	mx51_efikamx_board_id();
-
-	/* on < 1.2 boards both SD controllers are used */
-	if (system_rev < 0x12) {
-		imx51_add_sdhci_esdhc_imx(0, NULL);
-		imx51_add_sdhci_esdhc_imx(1, &sd_pdata);
-		mx51_efikamx_leds[2].default_trigger = "mmc1";
-	} else
-		imx51_add_sdhci_esdhc_imx(0, &sd_pdata);
-
-	gpio_led_register_device(-1, &mx51_efikamx_leds_data);
-	imx_add_gpio_keys(&mx51_efikamx_powerkey_data);
-
-	if (system_rev == 0x11) {
-		gpio_request(EFIKAMX_RESET1_1, "reset");
-		gpio_direction_output(EFIKAMX_RESET1_1, 1);
-	} else {
-		gpio_request(EFIKAMX_RESET, "reset");
-		gpio_direction_output(EFIKAMX_RESET, 1);
-	}
-
-	/*
-	 * enable wifi by default only on mx
-	 * sb and mx have same wlan pin but the value to enable it are
-	 * different :/
-	 */
-	gpio_request(EFIKA_WLAN_EN, "wlan_en");
-	gpio_direction_output(EFIKA_WLAN_EN, 0);
-	msleep(10);
-
-	gpio_request(EFIKA_WLAN_RESET, "wlan_rst");
-	gpio_direction_output(EFIKA_WLAN_RESET, 0);
-	msleep(10);
-	gpio_set_value(EFIKA_WLAN_RESET, 1);
-}
-
-static void __init mx51_efikamx_timer_init(void)
-{
-	mx51_clocks_init(32768, 24000000, 22579200, 24576000);
-}
-
-static struct sys_timer mx51_efikamx_timer = {
-	.init = mx51_efikamx_timer_init,
-};
-
-MACHINE_START(MX51_EFIKAMX, "Genesi Efika MX (Smarttop)")
-	.atag_offset = 0x100,
-	.map_io = mx51_map_io,
-	.init_early = imx51_init_early,
-	.init_irq = mx51_init_irq,
-	.handle_irq = imx51_handle_irq,
-	.timer = &mx51_efikamx_timer,
-	.init_machine = mx51_efikamx_init,
-	.init_late = mx51_efikamx_init_late,
-	.restart = mx51_efikamx_restart,
-MACHINE_END
diff --git a/arch/arm/mach-imx/mach-mx51_efikasb.c b/arch/arm/mach-imx/mach-mx51_efikasb.c
deleted file mode 100644
index fdbd181..0000000
--- a/arch/arm/mach-imx/mach-mx51_efikasb.c
+++ /dev/null
@@ -1,296 +0,0 @@
-/*
- * Copyright (C) Arnaud Patard <arnaud.patard@rtp-net.org>
- *
- * based on code from the following
- * Copyright 2009-2010 Freescale Semiconductor, Inc. All Rights Reserved.
- * Copyright 2009-2010 Pegatron Corporation. All Rights Reserved.
- * Copyright 2009-2010 Genesi USA, Inc. All Rights Reserved.
- *
- * The code contained herein is licensed under the GNU General Public
- * License. You may obtain a copy of the GNU General Public License
- * Version 2 or later at the following locations:
- *
- * http://www.opensource.org/licenses/gpl-license.html
- * http://www.gnu.org/copyleft/gpl.html
- */
-
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/i2c.h>
-#include <linux/gpio.h>
-#include <linux/leds.h>
-#include <linux/input.h>
-#include <linux/delay.h>
-#include <linux/io.h>
-#include <linux/spi/flash.h>
-#include <linux/spi/spi.h>
-#include <linux/mfd/mc13892.h>
-#include <linux/regulator/machine.h>
-#include <linux/regulator/consumer.h>
-#include <linux/usb/otg.h>
-#include <linux/usb/ulpi.h>
-#include <mach/ulpi.h>
-
-#include <mach/common.h>
-#include <mach/hardware.h>
-#include <mach/iomux-mx51.h>
-
-#include <asm/setup.h>
-#include <asm/system_info.h>
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/time.h>
-
-#include "devices-imx51.h"
-#include "efika.h"
-
-#define EFIKASB_USBH2_STP	IMX_GPIO_NR(2, 20)
-#define EFIKASB_GREEN_LED	IMX_GPIO_NR(1, 3)
-#define EFIKASB_WHITE_LED	IMX_GPIO_NR(2, 25)
-#define EFIKASB_PCBID0		IMX_GPIO_NR(2, 28)
-#define EFIKASB_PCBID1		IMX_GPIO_NR(2, 29)
-#define EFIKASB_PWRKEY		IMX_GPIO_NR(2, 31)
-#define EFIKASB_LID		IMX_GPIO_NR(3, 14)
-#define EFIKASB_POWEROFF	IMX_GPIO_NR(4, 13)
-#define EFIKASB_RFKILL		IMX_GPIO_NR(3, 1)
-
-#define MX51_PAD_PWRKEY IOMUX_PAD(0x48c, 0x0f8, 1, 0x0,   0, PAD_CTL_PUS_100K_UP | PAD_CTL_PKE)
-#define MX51_PAD_SD1_CD	IOMUX_PAD(0x47c, 0x0e8, 1, __NA_, 0, MX51_ESDHC_PAD_CTRL)
-
-static iomux_v3_cfg_t mx51efikasb_pads[] = {
-	/* USB HOST2 */
-	MX51_PAD_EIM_D16__USBH2_DATA0,
-	MX51_PAD_EIM_D17__USBH2_DATA1,
-	MX51_PAD_EIM_D18__USBH2_DATA2,
-	MX51_PAD_EIM_D19__USBH2_DATA3,
-	MX51_PAD_EIM_D20__USBH2_DATA4,
-	MX51_PAD_EIM_D21__USBH2_DATA5,
-	MX51_PAD_EIM_D22__USBH2_DATA6,
-	MX51_PAD_EIM_D23__USBH2_DATA7,
-	MX51_PAD_EIM_A24__USBH2_CLK,
-	MX51_PAD_EIM_A25__USBH2_DIR,
-	MX51_PAD_EIM_A26__USBH2_STP,
-	MX51_PAD_EIM_A27__USBH2_NXT,
-
-	/* leds */
-	MX51_PAD_EIM_CS0__GPIO2_25,
-	MX51_PAD_GPIO1_3__GPIO1_3,
-
-	/* pcb id */
-	MX51_PAD_EIM_CS3__GPIO2_28,
-	MX51_PAD_EIM_CS4__GPIO2_29,
-
-	/* lid */
-	MX51_PAD_CSI1_VSYNC__GPIO3_14,
-
-	/* power key*/
-	MX51_PAD_PWRKEY,
-
-	/* wifi/bt button */
-	MX51_PAD_DI1_PIN12__GPIO3_1,
-
-	/* power off */
-	MX51_PAD_CSI2_VSYNC__GPIO4_13,
-
-	/* wdog reset */
-	MX51_PAD_GPIO1_4__WDOG1_WDOG_B,
-
-	/* BT */
-	MX51_PAD_EIM_A17__GPIO2_11,
-
-	MX51_PAD_SD1_CD,
-};
-
-static int initialize_usbh2_port(struct platform_device *pdev)
-{
-	iomux_v3_cfg_t usbh2stp = MX51_PAD_EIM_A26__USBH2_STP;
-	iomux_v3_cfg_t usbh2gpio = MX51_PAD_EIM_A26__GPIO2_20;
-
-	mxc_iomux_v3_setup_pad(usbh2gpio);
-	gpio_request(EFIKASB_USBH2_STP, "usbh2_stp");
-	gpio_direction_output(EFIKASB_USBH2_STP, 0);
-	msleep(1);
-	gpio_set_value(EFIKASB_USBH2_STP, 1);
-	msleep(1);
-
-	gpio_free(EFIKASB_USBH2_STP);
-	mxc_iomux_v3_setup_pad(usbh2stp);
-
-	mdelay(10);
-
-	return mx51_initialize_usb_hw(pdev->id, MXC_EHCI_ITC_NO_THRESHOLD);
-}
-
-static struct mxc_usbh_platform_data usbh2_config __initdata = {
-	.init   = initialize_usbh2_port,
-	.portsc = MXC_EHCI_MODE_ULPI,
-};
-
-static void __init mx51_efikasb_usb(void)
-{
-	usbh2_config.otg = imx_otg_ulpi_create(ULPI_OTG_DRVVBUS |
-			ULPI_OTG_DRVVBUS_EXT | ULPI_OTG_EXTVBUSIND);
-	if (usbh2_config.otg)
-		imx51_add_mxc_ehci_hs(2, &usbh2_config);
-}
-
-static const struct gpio_led mx51_efikasb_leds[] __initconst = {
-	{
-		.name = "efikasb:green",
-		.default_trigger = "default-on",
-		.gpio = EFIKASB_GREEN_LED,
-		.active_low = 1,
-	},
-	{
-		.name = "efikasb:white",
-		.default_trigger = "caps",
-		.gpio = EFIKASB_WHITE_LED,
-	},
-};
-
-static const struct gpio_led_platform_data
-		mx51_efikasb_leds_data __initconst = {
-	.leds = mx51_efikasb_leds,
-	.num_leds = ARRAY_SIZE(mx51_efikasb_leds),
-};
-
-static struct gpio_keys_button mx51_efikasb_keys[] = {
-	{
-		.code = KEY_POWER,
-		.gpio = EFIKASB_PWRKEY,
-		.type = EV_KEY,
-		.desc = "Power Button",
-		.wakeup = 1,
-		.active_low = 1,
-	},
-	{
-		.code = SW_LID,
-		.gpio = EFIKASB_LID,
-		.type = EV_SW,
-		.desc = "Lid Switch",
-		.active_low = 1,
-	},
-	{
-		.code = KEY_RFKILL,
-		.gpio = EFIKASB_RFKILL,
-		.type = EV_KEY,
-		.desc = "rfkill",
-		.active_low = 1,
-	},
-};
-
-static const struct gpio_keys_platform_data mx51_efikasb_keys_data __initconst = {
-	.buttons = mx51_efikasb_keys,
-	.nbuttons = ARRAY_SIZE(mx51_efikasb_keys),
-};
-
-static struct esdhc_platform_data sd0_pdata = {
-#define EFIKASB_SD1_CD	IMX_GPIO_NR(2, 27)
-	.cd_gpio = EFIKASB_SD1_CD,
-	.cd_type = ESDHC_CD_GPIO,
-	.wp_type = ESDHC_WP_CONTROLLER,
-};
-
-static struct esdhc_platform_data sd1_pdata = {
-	.cd_type = ESDHC_CD_CONTROLLER,
-	.wp_type = ESDHC_WP_CONTROLLER,
-};
-
-static struct regulator *pwgt1, *pwgt2;
-
-static void mx51_efikasb_power_off(void)
-{
-	gpio_set_value(EFIKA_USB_PHY_RESET, 0);
-
-	if (!IS_ERR(pwgt1) && !IS_ERR(pwgt2)) {
-		regulator_disable(pwgt2);
-		regulator_disable(pwgt1);
-	}
-	gpio_direction_output(EFIKASB_POWEROFF, 1);
-}
-
-static int __init mx51_efikasb_power_init(void)
-{
-	pwgt1 = regulator_get(NULL, "pwgt1");
-	pwgt2 = regulator_get(NULL, "pwgt2");
-	if (!IS_ERR(pwgt1) && !IS_ERR(pwgt2)) {
-		regulator_enable(pwgt1);
-		regulator_enable(pwgt2);
-	}
-	gpio_request(EFIKASB_POWEROFF, "poweroff");
-	pm_power_off = mx51_efikasb_power_off;
-
-	regulator_has_full_constraints();
-
-	return 0;
-}
-
-static void __init mx51_efikasb_init_late(void)
-{
-	imx51_init_late();
-	mx51_efikasb_power_init();
-}
-
-/* 01     R1.3 board
-   10     R2.0 board */
-static void __init mx51_efikasb_board_id(void)
-{
-	int id;
-
-	gpio_request(EFIKASB_PCBID0, "pcb id0");
-	gpio_direction_input(EFIKASB_PCBID0);
-	gpio_request(EFIKASB_PCBID1, "pcb id1");
-	gpio_direction_input(EFIKASB_PCBID1);
-
-	id = gpio_get_value(EFIKASB_PCBID0) ? 1 : 0;
-	id |= (gpio_get_value(EFIKASB_PCBID1) ? 1 : 0) << 1;
-
-	switch (id) {
-	default:
-		break;
-	case 1:
-		system_rev = 0x13;
-		break;
-	case 2:
-		system_rev = 0x20;
-		break;
-	}
-}
-
-static void __init efikasb_board_init(void)
-{
-	imx51_soc_init();
-
-	mxc_iomux_v3_setup_multiple_pads(mx51efikasb_pads,
-					ARRAY_SIZE(mx51efikasb_pads));
-	efika_board_common_init();
-
-	mx51_efikasb_board_id();
-	mx51_efikasb_usb();
-	imx51_add_sdhci_esdhc_imx(0, &sd0_pdata);
-	imx51_add_sdhci_esdhc_imx(1, &sd1_pdata);
-
-	gpio_led_register_device(-1, &mx51_efikasb_leds_data);
-	imx_add_gpio_keys(&mx51_efikasb_keys_data);
-}
-
-static void __init mx51_efikasb_timer_init(void)
-{
-	mx51_clocks_init(32768, 24000000, 22579200, 24576000);
-}
-
-static struct sys_timer mx51_efikasb_timer = {
-	.init	= mx51_efikasb_timer_init,
-};
-
-MACHINE_START(MX51_EFIKASB, "Genesi Efika MX (Smartbook)")
-	.atag_offset = 0x100,
-	.map_io = mx51_map_io,
-	.init_early = imx51_init_early,
-	.init_irq = mx51_init_irq,
-	.handle_irq = imx51_handle_irq,
-	.init_machine =  efikasb_board_init,
-	.init_late = mx51_efikasb_init_late,
-	.timer = &mx51_efikasb_timer,
-	.restart	= mxc_restart,
-MACHINE_END
diff --git a/arch/arm/mach-imx/mx51_efika.c b/arch/arm/mach-imx/mx51_efika.c
deleted file mode 100644
index ec6ca91..0000000
--- a/arch/arm/mach-imx/mx51_efika.c
+++ /dev/null
@@ -1,632 +0,0 @@
-/*
- * based on code from the following
- * Copyright 2009-2010 Freescale Semiconductor, Inc. All Rights Reserved.
- * Copyright 2009-2010 Pegatron Corporation. All Rights Reserved.
- * Copyright 2009-2010 Genesi USA, Inc. All Rights Reserved.
- *
- * The code contained herein is licensed under the GNU General Public
- * License. You may obtain a copy of the GNU General Public License
- * Version 2 or later at the following locations:
- *
- * http://www.opensource.org/licenses/gpl-license.html
- * http://www.gnu.org/copyleft/gpl.html
- */
-
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/i2c.h>
-#include <linux/gpio.h>
-#include <linux/leds.h>
-#include <linux/input.h>
-#include <linux/delay.h>
-#include <linux/io.h>
-#include <linux/spi/flash.h>
-#include <linux/spi/spi.h>
-#include <linux/mfd/mc13892.h>
-#include <linux/regulator/machine.h>
-#include <linux/regulator/consumer.h>
-
-#include <mach/common.h>
-#include <mach/hardware.h>
-#include <mach/iomux-mx51.h>
-
-#include <linux/usb/otg.h>
-#include <linux/usb/ulpi.h>
-#include <mach/ulpi.h>
-
-#include <asm/setup.h>
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/time.h>
-
-#include "devices-imx51.h"
-#include "efika.h"
-#include "cpu_op-mx51.h"
-
-#define MX51_USB_CTRL_1_OFFSET          0x10
-#define MX51_USB_CTRL_UH1_EXT_CLK_EN    (1 << 25)
-#define	MX51_USB_PLL_DIV_19_2_MHZ	0x01
-
-#define EFIKAMX_USB_HUB_RESET	IMX_GPIO_NR(1, 5)
-#define EFIKAMX_USBH1_STP	IMX_GPIO_NR(1, 27)
-
-#define EFIKAMX_SPI_CS0		IMX_GPIO_NR(4, 24)
-#define EFIKAMX_SPI_CS1		IMX_GPIO_NR(4, 25)
-
-#define EFIKAMX_PMIC		IMX_GPIO_NR(1, 6)
-
-static iomux_v3_cfg_t mx51efika_pads[] = {
-	/* UART1 */
-	MX51_PAD_UART1_RXD__UART1_RXD,
-	MX51_PAD_UART1_TXD__UART1_TXD,
-	MX51_PAD_UART1_RTS__UART1_RTS,
-	MX51_PAD_UART1_CTS__UART1_CTS,
-
-	/* SD 1 */
-	MX51_PAD_SD1_CMD__SD1_CMD,
-	MX51_PAD_SD1_CLK__SD1_CLK,
-	MX51_PAD_SD1_DATA0__SD1_DATA0,
-	MX51_PAD_SD1_DATA1__SD1_DATA1,
-	MX51_PAD_SD1_DATA2__SD1_DATA2,
-	MX51_PAD_SD1_DATA3__SD1_DATA3,
-
-	/* SD 2 */
-	MX51_PAD_SD2_CMD__SD2_CMD,
-	MX51_PAD_SD2_CLK__SD2_CLK,
-	MX51_PAD_SD2_DATA0__SD2_DATA0,
-	MX51_PAD_SD2_DATA1__SD2_DATA1,
-	MX51_PAD_SD2_DATA2__SD2_DATA2,
-	MX51_PAD_SD2_DATA3__SD2_DATA3,
-
-	/* SD/MMC WP/CD */
-	MX51_PAD_GPIO1_0__SD1_CD,
-	MX51_PAD_GPIO1_1__SD1_WP,
-	MX51_PAD_GPIO1_7__SD2_WP,
-	MX51_PAD_GPIO1_8__SD2_CD,
-
-	/* spi */
-	MX51_PAD_CSPI1_MOSI__ECSPI1_MOSI,
-	MX51_PAD_CSPI1_MISO__ECSPI1_MISO,
-	MX51_PAD_CSPI1_SS0__GPIO4_24,
-	MX51_PAD_CSPI1_SS1__GPIO4_25,
-	MX51_PAD_CSPI1_RDY__ECSPI1_RDY,
-	MX51_PAD_CSPI1_SCLK__ECSPI1_SCLK,
-	MX51_PAD_GPIO1_6__GPIO1_6,
-
-	/* USB HOST1 */
-	MX51_PAD_USBH1_CLK__USBH1_CLK,
-	MX51_PAD_USBH1_DIR__USBH1_DIR,
-	MX51_PAD_USBH1_NXT__USBH1_NXT,
-	MX51_PAD_USBH1_DATA0__USBH1_DATA0,
-	MX51_PAD_USBH1_DATA1__USBH1_DATA1,
-	MX51_PAD_USBH1_DATA2__USBH1_DATA2,
-	MX51_PAD_USBH1_DATA3__USBH1_DATA3,
-	MX51_PAD_USBH1_DATA4__USBH1_DATA4,
-	MX51_PAD_USBH1_DATA5__USBH1_DATA5,
-	MX51_PAD_USBH1_DATA6__USBH1_DATA6,
-	MX51_PAD_USBH1_DATA7__USBH1_DATA7,
-
-	/* USB HUB RESET */
-	MX51_PAD_GPIO1_5__GPIO1_5,
-
-	/* WLAN */
-	MX51_PAD_EIM_A22__GPIO2_16,
-	MX51_PAD_EIM_A16__GPIO2_10,
-
-	/* USB PHY RESET */
-	MX51_PAD_EIM_D27__GPIO2_9,
-};
-
-/* Serial ports */
-static const struct imxuart_platform_data uart_pdata = {
-	.flags = IMXUART_HAVE_RTSCTS,
-};
-
-/* This function is board specific as the bit mask for the plldiv will also
- * be different for other Freescale SoCs, thus a common bitmask is not
- * possible and cannot get place in /plat-mxc/ehci.c.
- */
-static int initialize_otg_port(struct platform_device *pdev)
-{
-	u32 v;
-	void __iomem *usb_base;
-	void __iomem *usbother_base;
-	usb_base = ioremap(MX51_USB_OTG_BASE_ADDR, SZ_4K);
-	if (!usb_base)
-		return -ENOMEM;
-	usbother_base = (void __iomem *)(usb_base + MX5_USBOTHER_REGS_OFFSET);
-
-	/* Set the PHY clock to 19.2MHz */
-	v = __raw_readl(usbother_base + MXC_USB_PHY_CTR_FUNC2_OFFSET);
-	v &= ~MX5_USB_UTMI_PHYCTRL1_PLLDIV_MASK;
-	v |= MX51_USB_PLL_DIV_19_2_MHZ;
-	__raw_writel(v, usbother_base + MXC_USB_PHY_CTR_FUNC2_OFFSET);
-	iounmap(usb_base);
-
-	mdelay(10);
-
-	return mx51_initialize_usb_hw(pdev->id, MXC_EHCI_INTERNAL_PHY);
-}
-
-static const struct mxc_usbh_platform_data dr_utmi_config __initconst = {
-	.init   = initialize_otg_port,
-	.portsc = MXC_EHCI_UTMI_16BIT,
-};
-
-static int initialize_usbh1_port(struct platform_device *pdev)
-{
-	iomux_v3_cfg_t usbh1stp = MX51_PAD_USBH1_STP__USBH1_STP;
-	iomux_v3_cfg_t usbh1gpio = MX51_PAD_USBH1_STP__GPIO1_27;
-	u32 v;
-	void __iomem *usb_base;
-	void __iomem *socregs_base;
-
-	mxc_iomux_v3_setup_pad(usbh1gpio);
-	gpio_request(EFIKAMX_USBH1_STP, "usbh1_stp");
-	gpio_direction_output(EFIKAMX_USBH1_STP, 0);
-	msleep(1);
-	gpio_set_value(EFIKAMX_USBH1_STP, 1);
-	msleep(1);
-
-	usb_base = ioremap(MX51_USB_OTG_BASE_ADDR, SZ_4K);
-	socregs_base = (void __iomem *)(usb_base + MX5_USBOTHER_REGS_OFFSET);
-
-	/* The clock for the USBH1 ULPI port will come externally */
-	/* from the PHY. */
-	v = __raw_readl(socregs_base + MX51_USB_CTRL_1_OFFSET);
-	__raw_writel(v | MX51_USB_CTRL_UH1_EXT_CLK_EN,
-			socregs_base + MX51_USB_CTRL_1_OFFSET);
-
-	iounmap(usb_base);
-
-	gpio_free(EFIKAMX_USBH1_STP);
-	mxc_iomux_v3_setup_pad(usbh1stp);
-
-	mdelay(10);
-
-	return mx51_initialize_usb_hw(pdev->id, MXC_EHCI_ITC_NO_THRESHOLD);
-}
-
-static struct mxc_usbh_platform_data usbh1_config __initdata = {
-	.init   = initialize_usbh1_port,
-	.portsc = MXC_EHCI_MODE_ULPI,
-};
-
-static void mx51_efika_hubreset(void)
-{
-	gpio_request(EFIKAMX_USB_HUB_RESET, "usb_hub_rst");
-	gpio_direction_output(EFIKAMX_USB_HUB_RESET, 1);
-	msleep(1);
-	gpio_set_value(EFIKAMX_USB_HUB_RESET, 0);
-	msleep(1);
-	gpio_set_value(EFIKAMX_USB_HUB_RESET, 1);
-}
-
-static void __init mx51_efika_usb(void)
-{
-	mx51_efika_hubreset();
-
-	/* pulling it low, means no USB at all... */
-	gpio_request(EFIKA_USB_PHY_RESET, "usb_phy_reset");
-	gpio_direction_output(EFIKA_USB_PHY_RESET, 0);
-	msleep(1);
-	gpio_set_value(EFIKA_USB_PHY_RESET, 1);
-
-	usbh1_config.otg = imx_otg_ulpi_create(ULPI_OTG_DRVVBUS |
-			ULPI_OTG_DRVVBUS_EXT | ULPI_OTG_EXTVBUSIND);
-
-	imx51_add_mxc_ehci_otg(&dr_utmi_config);
-	if (usbh1_config.otg)
-		imx51_add_mxc_ehci_hs(1, &usbh1_config);
-}
-
-static struct mtd_partition mx51_efika_spi_nor_partitions[] = {
-	{
-	 .name = "u-boot",
-	 .offset = 0,
-	 .size = SZ_256K,
-	},
-	{
-	  .name = "config",
-	  .offset = MTDPART_OFS_APPEND,
-	  .size = SZ_64K,
-	},
-};
-
-static struct flash_platform_data mx51_efika_spi_flash_data = {
-	.name		= "spi_flash",
-	.parts		= mx51_efika_spi_nor_partitions,
-	.nr_parts	= ARRAY_SIZE(mx51_efika_spi_nor_partitions),
-	.type		= "sst25vf032b",
-};
-
-static struct regulator_consumer_supply sw1_consumers[] = {
-	{
-		.supply = "cpu_vcc",
-	}
-};
-
-static struct regulator_consumer_supply vdig_consumers[] = {
-	/* sgtl5000 */
-	REGULATOR_SUPPLY("VDDA", "1-000a"),
-	REGULATOR_SUPPLY("VDDD", "1-000a"),
-};
-
-static struct regulator_consumer_supply vvideo_consumers[] = {
-	/* sgtl5000 */
-	REGULATOR_SUPPLY("VDDIO", "1-000a"),
-};
-
-static struct regulator_consumer_supply vsd_consumers[] = {
-	REGULATOR_SUPPLY("vmmc", "sdhci-esdhc-imx51.0"),
-	REGULATOR_SUPPLY("vmmc", "sdhci-esdhc-imx51.1"),
-};
-
-static struct regulator_consumer_supply pwgt1_consumer[] = {
-	{
-		.supply = "pwgt1",
-	}
-};
-
-static struct regulator_consumer_supply pwgt2_consumer[] = {
-	{
-		.supply = "pwgt2",
-	}
-};
-
-static struct regulator_consumer_supply coincell_consumer[] = {
-	{
-		.supply = "coincell",
-	}
-};
-
-static struct regulator_init_data sw1_init = {
-	.constraints = {
-		.name = "SW1",
-		.min_uV = 600000,
-		.max_uV = 1375000,
-		.valid_ops_mask = REGULATOR_CHANGE_VOLTAGE,
-		.valid_modes_mask = 0,
-		.always_on = 1,
-		.boot_on = 1,
-		.state_mem = {
-			.uV = 850000,
-			.mode = REGULATOR_MODE_NORMAL,
-			.enabled = 1,
-		},
-	},
-	.num_consumer_supplies = ARRAY_SIZE(sw1_consumers),
-	.consumer_supplies = sw1_consumers,
-};
-
-static struct regulator_init_data sw2_init = {
-	.constraints = {
-		.name = "SW2",
-		.min_uV = 900000,
-		.max_uV = 1850000,
-		.valid_ops_mask = REGULATOR_CHANGE_VOLTAGE,
-		.always_on = 1,
-		.boot_on = 1,
-		.state_mem = {
-			.uV = 950000,
-			.mode = REGULATOR_MODE_NORMAL,
-			.enabled = 1,
-		},
-	}
-};
-
-static struct regulator_init_data sw3_init = {
-	.constraints = {
-		.name = "SW3",
-		.min_uV = 1100000,
-		.max_uV = 1850000,
-		.valid_ops_mask = REGULATOR_CHANGE_VOLTAGE,
-		.always_on = 1,
-		.boot_on = 1,
-	}
-};
-
-static struct regulator_init_data sw4_init = {
-	.constraints = {
-		.name = "SW4",
-		.min_uV = 1100000,
-		.max_uV = 1850000,
-		.valid_ops_mask = REGULATOR_CHANGE_VOLTAGE,
-		.always_on = 1,
-		.boot_on = 1,
-	}
-};
-
-static struct regulator_init_data viohi_init = {
-	.constraints = {
-		.name = "VIOHI",
-		.boot_on = 1,
-		.always_on = 1,
-	}
-};
-
-static struct regulator_init_data vusb_init = {
-	.constraints = {
-		.name = "VUSB",
-		.boot_on = 1,
-		.always_on = 1,
-	}
-};
-
-static struct regulator_init_data swbst_init = {
-	.constraints = {
-		.name = "SWBST",
-	}
-};
-
-static struct regulator_init_data vdig_init = {
-	.constraints = {
-		.name = "VDIG",
-		.min_uV = 1050000,
-		.max_uV = 1800000,
-		.valid_ops_mask =
-			REGULATOR_CHANGE_VOLTAGE | REGULATOR_CHANGE_STATUS,
-		.boot_on = 1,
-		.always_on = 1,
-	},
-	.num_consumer_supplies = ARRAY_SIZE(vdig_consumers),
-	.consumer_supplies = vdig_consumers,
-};
-
-static struct regulator_init_data vpll_init = {
-	.constraints = {
-		.name = "VPLL",
-		.min_uV = 1050000,
-		.max_uV = 1800000,
-		.valid_ops_mask =
-			REGULATOR_CHANGE_VOLTAGE | REGULATOR_CHANGE_STATUS,
-		.boot_on = 1,
-		.always_on = 1,
-	}
-};
-
-static struct regulator_init_data vusb2_init = {
-	.constraints = {
-		.name = "VUSB2",
-		.min_uV = 2400000,
-		.max_uV = 2775000,
-		.valid_ops_mask = REGULATOR_CHANGE_VOLTAGE,
-		.boot_on = 1,
-		.always_on = 1,
-	}
-};
-
-static struct regulator_init_data vvideo_init = {
-	.constraints = {
-		.name = "VVIDEO",
-		.min_uV = 2775000,
-		.max_uV = 2775000,
-		.valid_ops_mask =
-			REGULATOR_CHANGE_VOLTAGE | REGULATOR_CHANGE_STATUS,
-		.boot_on = 1,
-		.apply_uV = 1,
-	},
-	.num_consumer_supplies = ARRAY_SIZE(vvideo_consumers),
-	.consumer_supplies = vvideo_consumers,
-};
-
-static struct regulator_init_data vaudio_init = {
-	.constraints = {
-		.name = "VAUDIO",
-		.min_uV = 2300000,
-		.max_uV = 3000000,
-		.valid_ops_mask =
-			REGULATOR_CHANGE_VOLTAGE | REGULATOR_CHANGE_STATUS,
-		.boot_on = 1,
-	}
-};
-
-static struct regulator_init_data vsd_init = {
-	.constraints = {
-		.name = "VSD",
-		.min_uV = 1800000,
-		.max_uV = 3150000,
-		.valid_ops_mask =
-			REGULATOR_CHANGE_VOLTAGE,
-		.boot_on = 1,
-	},
-	.num_consumer_supplies = ARRAY_SIZE(vsd_consumers),
-	.consumer_supplies = vsd_consumers,
-};
-
-static struct regulator_init_data vcam_init = {
-	.constraints = {
-		.name = "VCAM",
-		.min_uV = 2500000,
-		.max_uV = 3000000,
-		.valid_ops_mask =
-			REGULATOR_CHANGE_VOLTAGE |
-			REGULATOR_CHANGE_MODE | REGULATOR_CHANGE_STATUS,
-		.valid_modes_mask = REGULATOR_MODE_FAST | REGULATOR_MODE_NORMAL,
-		.boot_on = 1,
-	}
-};
-
-static struct regulator_init_data vgen1_init = {
-	.constraints = {
-		.name = "VGEN1",
-		.min_uV = 1200000,
-		.max_uV = 3150000,
-		.valid_ops_mask =
-			REGULATOR_CHANGE_VOLTAGE | REGULATOR_CHANGE_STATUS,
-		.boot_on = 1,
-		.always_on = 1,
-	}
-};
-
-static struct regulator_init_data vgen2_init = {
-	.constraints = {
-		.name = "VGEN2",
-		.min_uV = 1200000,
-		.max_uV = 3150000,
-		.valid_ops_mask =
-			REGULATOR_CHANGE_VOLTAGE | REGULATOR_CHANGE_STATUS,
-		.boot_on = 1,
-		.always_on = 1,
-	}
-};
-
-static struct regulator_init_data vgen3_init = {
-	.constraints = {
-		.name = "VGEN3",
-		.min_uV = 1800000,
-		.max_uV = 2900000,
-		.valid_ops_mask =
-			REGULATOR_CHANGE_VOLTAGE | REGULATOR_CHANGE_STATUS,
-		.boot_on = 1,
-		.always_on = 1,
-	}
-};
-
-static struct regulator_init_data gpo1_init = {
-	.constraints = {
-		.name = "GPO1",
-	}
-};
-
-static struct regulator_init_data gpo2_init = {
-	.constraints = {
-		.name = "GPO2",
-	}
-};
-
-static struct regulator_init_data gpo3_init = {
-	.constraints = {
-		.name = "GPO3",
-	}
-};
-
-static struct regulator_init_data gpo4_init = {
-	.constraints = {
-		.name = "GPO4",
-	}
-};
-
-static struct regulator_init_data pwgt1_init = {
-	.constraints = {
-		.valid_ops_mask = REGULATOR_CHANGE_STATUS,
-		.boot_on        = 1,
-	},
-	.num_consumer_supplies = ARRAY_SIZE(pwgt1_consumer),
-	.consumer_supplies = pwgt1_consumer,
-};
-
-static struct regulator_init_data pwgt2_init = {
-	.constraints = {
-		.valid_ops_mask = REGULATOR_CHANGE_STATUS,
-		.boot_on        = 1,
-	},
-	.num_consumer_supplies = ARRAY_SIZE(pwgt2_consumer),
-	.consumer_supplies = pwgt2_consumer,
-};
-
-static struct regulator_init_data vcoincell_init = {
-	.constraints = {
-		.name = "COINCELL",
-		.min_uV = 3000000,
-		.max_uV = 3000000,
-		.valid_ops_mask =
-			REGULATOR_CHANGE_VOLTAGE | REGULATOR_CHANGE_STATUS,
-	},
-	.num_consumer_supplies = ARRAY_SIZE(coincell_consumer),
-	.consumer_supplies = coincell_consumer,
-};
-
-static struct mc13xxx_regulator_init_data mx51_efika_regulators[] = {
-	{ .id = MC13892_SW1,		.init_data =  &sw1_init },
-	{ .id = MC13892_SW2,		.init_data =  &sw2_init },
-	{ .id = MC13892_SW3,		.init_data =  &sw3_init },
-	{ .id = MC13892_SW4,		.init_data =  &sw4_init },
-	{ .id = MC13892_SWBST,		.init_data =  &swbst_init },
-	{ .id = MC13892_VIOHI,		.init_data =  &viohi_init },
-	{ .id = MC13892_VPLL,		.init_data =  &vpll_init },
-	{ .id = MC13892_VDIG,		.init_data =  &vdig_init },
-	{ .id = MC13892_VSD,		.init_data =  &vsd_init },
-	{ .id = MC13892_VUSB2,		.init_data =  &vusb2_init },
-	{ .id = MC13892_VVIDEO,		.init_data =  &vvideo_init },
-	{ .id = MC13892_VAUDIO,		.init_data =  &vaudio_init },
-	{ .id = MC13892_VCAM,		.init_data =  &vcam_init },
-	{ .id = MC13892_VGEN1,		.init_data =  &vgen1_init },
-	{ .id = MC13892_VGEN2,		.init_data =  &vgen2_init },
-	{ .id = MC13892_VGEN3,		.init_data =  &vgen3_init },
-	{ .id = MC13892_VUSB,		.init_data =  &vusb_init },
-	{ .id = MC13892_GPO1,		.init_data =  &gpo1_init },
-	{ .id = MC13892_GPO2,		.init_data =  &gpo2_init },
-	{ .id = MC13892_GPO3,		.init_data =  &gpo3_init },
-	{ .id = MC13892_GPO4,		.init_data =  &gpo4_init },
-	{ .id = MC13892_PWGT1SPI,	.init_data = &pwgt1_init },
-	{ .id = MC13892_PWGT2SPI,	.init_data = &pwgt2_init },
-	{ .id = MC13892_VCOINCELL,	.init_data = &vcoincell_init },
-};
-
-static struct mc13xxx_platform_data mx51_efika_mc13892_data = {
-	.flags = MC13XXX_USE_RTC,
-	.regulators = {
-		.num_regulators = ARRAY_SIZE(mx51_efika_regulators),
-		.regulators = mx51_efika_regulators,
-	},
-};
-
-static struct spi_board_info mx51_efika_spi_board_info[] __initdata = {
-	{
-		.modalias = "m25p80",
-		.max_speed_hz = 25000000,
-		.bus_num = 0,
-		.chip_select = 1,
-		.platform_data = &mx51_efika_spi_flash_data,
-		.irq = -1,
-	},
-	{
-		.modalias = "mc13892",
-		.max_speed_hz = 1000000,
-		.bus_num = 0,
-		.chip_select = 0,
-		.platform_data = &mx51_efika_mc13892_data,
-		.irq = IMX_GPIO_TO_IRQ(EFIKAMX_PMIC),
-	},
-};
-
-static int mx51_efika_spi_cs[] = {
-	EFIKAMX_SPI_CS0,
-	EFIKAMX_SPI_CS1,
-};
-
-static const struct spi_imx_master mx51_efika_spi_pdata __initconst = {
-	.chipselect     = mx51_efika_spi_cs,
-	.num_chipselect = ARRAY_SIZE(mx51_efika_spi_cs),
-};
-
-void __init efika_board_common_init(void)
-{
-	mxc_iomux_v3_setup_multiple_pads(mx51efika_pads,
-					ARRAY_SIZE(mx51efika_pads));
-	imx51_add_imx_uart(0, &uart_pdata);
-	mx51_efika_usb();
-
-	/* FIXME: comes from original code. check this. */
-	if (mx51_revision() < IMX_CHIP_REVISION_2_0)
-		sw2_init.constraints.state_mem.uV = 1100000;
-	else if (mx51_revision() == IMX_CHIP_REVISION_2_0) {
-		sw2_init.constraints.state_mem.uV = 1250000;
-		sw1_init.constraints.state_mem.uV = 1000000;
-	}
-	if (machine_is_mx51_efikasb())
-		vgen1_init.constraints.max_uV = 1200000;
-
-	gpio_request(EFIKAMX_PMIC, "pmic irq");
-	gpio_direction_input(EFIKAMX_PMIC);
-	spi_register_board_info(mx51_efika_spi_board_info,
-		ARRAY_SIZE(mx51_efika_spi_board_info));
-	imx51_add_ecspi(0, &mx51_efika_spi_pdata);
-
-	imx51_add_pata_imx();
-
-#if defined(CONFIG_CPU_FREQ_IMX)
-	get_cpu_op = mx51_get_cpu_op;
-#endif
-}
