| Message ID | 1345114051-3052-4-git-send-email-jason77.wang@gmail.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
On Thu, Aug 16, 2012 at 06:47:31PM +0800, Hui Wang wrote: > i.MX6Q sabrelite board uses i2c3 to connect an eeti egalax > touchscreen controller, add it as an i2c slave device in the dts. > > Signed-off-by: Hui Wang <jason77.wang@gmail.com> Looks good. Will apply it after the driver part gets accepted.
Shawn Guo wrote: > On Thu, Aug 16, 2012 at 06:47:31PM +0800, Hui Wang wrote: > >> i.MX6Q sabrelite board uses i2c3 to connect an eeti egalax >> touchscreen controller, add it as an i2c slave device in the dts. >> >> Signed-off-by: Hui Wang <jason77.wang@gmail.com> >> > > Looks good. Will apply it after the driver part gets accepted. > > Got it, thanks. Regards, Hui.
diff --git a/arch/arm/boot/dts/imx6q-sabrelite.dts b/arch/arm/boot/dts/imx6q-sabrelite.dts index 72f30f3..337ec74 100644 --- a/arch/arm/boot/dts/imx6q-sabrelite.dts +++ b/arch/arm/boot/dts/imx6q-sabrelite.dts @@ -54,6 +54,7 @@ 144 0x80000000 /* MX6Q_PAD_EIM_D22__GPIO_3_22 */ 121 0x80000000 /* MX6Q_PAD_EIM_D19__GPIO_3_19 */ 953 0x80000000 /* MX6Q_PAD_GPIO_0__CCM_CLKO */ + 972 0x10 /* MX6Q_PAD_GPIO_9__GPIO_1_9 */ >; }; }; @@ -115,6 +116,21 @@ VDDIO-supply = <®_3p3v>; }; }; + + i2c@021a8000 { /* I2C3 */ + status = "okay"; + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c3_1>; + + egalax_ts@04 { + compatible = "eeti,egalax_ts"; + reg = <0x04>; + interrupt-parent = <&gpio1>; + interrupts = <9 8>; + wakeup-gpios = <&gpio1 9 0>; + }; + }; }; }; diff --git a/arch/arm/boot/dts/imx6q.dtsi b/arch/arm/boot/dts/imx6q.dtsi index fd57079..6f833b3 100644 --- a/arch/arm/boot/dts/imx6q.dtsi +++ b/arch/arm/boot/dts/imx6q.dtsi @@ -552,6 +552,13 @@ }; }; + i2c3 { + pinctrl_i2c3_1: i2c3grp-1 { + fsl,pins = <1013 0x4001b8b1 /* MX6Q_PAD_GPIO_5__I2C3_SCL */ + 1037 0x4001b8b1>; /* MX6Q_PAD_GPIO_16__I2C3_SDA */ + }; + }; + serial2 { pinctrl_serial2_1: serial2grp-1 { fsl,pins = <183 0x1b0b1 /* MX6Q_PAD_EIM_D26__UART2_TXD */
i.MX6Q sabrelite board uses i2c3 to connect an eeti egalax touchscreen controller, add it as an i2c slave device in the dts. Signed-off-by: Hui Wang <jason77.wang@gmail.com> --- arch/arm/boot/dts/imx6q-sabrelite.dts | 16 ++++++++++++++++ arch/arm/boot/dts/imx6q.dtsi | 7 +++++++ 2 files changed, 23 insertions(+), 0 deletions(-)