@@ -6,11 +6,19 @@ Required properties:
- reg : Address and length of the register set for the device
- interrupts : Should contain the auart interrupt numbers
+Optional properties:
+- fsl,auart-dma-channel : The DMA channels, the first is for RX, the other
+ is for TX. If you add this property, it also means that you
+ will enable the DMA support for the auart.
+ Note: due to the hardware bug in imx23(see errata : 2836),
+ only the imx28 can enable the DMA support for the auart.
+
Example:
auart0: serial@8006a000 {
compatible = "fsl,imx28-auart", "fsl,imx23-auart";
reg = <0x8006a000 0x2000>;
interrupts = <112 70 71>;
+ fsl,auart-dma-channel = <8 9>;
};
Note: Each auart port should have an alias correctly numbered in "aliases"
@@ -34,6 +34,8 @@
#include <linux/io.h>
#include <linux/pinctrl/consumer.h>
#include <linux/of_device.h>
+#include <linux/dma-mapping.h>
+#include <linux/fsl/mxs-dma.h>
#include <asm/cacheflush.h>
@@ -71,6 +73,15 @@
#define AUART_CTRL0_SFTRST (1 << 31)
#define AUART_CTRL0_CLKGATE (1 << 30)
+#define AUART_CTRL0_RXTO_ENABLE (1 << 27)
+#define AUART_CTRL0_RXTIMEOUT(v) (((v) & 0x7ff) << 16)
+#define AUART_CTRL0_XFER_COUNT(v) ((v) & 0xffff)
+
+#define AUART_CTRL1_XFER_COUNT(v) ((v) & 0xffff)
+
+#define AUART_CTRL2_DMAONERR (1 << 26)
+#define AUART_CTRL2_TXDMAE (1 << 25)
+#define AUART_CTRL2_RXDMAE (1 << 24)
#define AUART_CTRL2_CTSEN (1 << 15)
#define AUART_CTRL2_RTSEN (1 << 14)
@@ -111,6 +122,7 @@
#define AUART_STAT_BERR (1 << 18)
#define AUART_STAT_PERR (1 << 17)
#define AUART_STAT_FERR (1 << 16)
+#define AUART_STAT_RXCOUNT_MASK 0xffff
static struct uart_driver auart_driver;
@@ -122,7 +134,11 @@ enum mxs_auart_type {
struct mxs_auart_port {
struct uart_port port;
- unsigned int flags;
+#define MXS_AUART_DMA_CONFIG 0x1
+#define MXS_AUART_DMA_ENABLED 0x2
+#define MXS_AUART_DMA_TX_SYNC 2 /* bit 2 */
+#define MXS_AUART_DMA_RX_READY 3 /* bit 3 */
+ unsigned long flags;
unsigned int ctrl;
enum mxs_auart_type devtype;
@@ -130,6 +146,20 @@ struct mxs_auart_port {
struct clk *clk;
struct device *dev;
+
+ /* for DMA */
+ struct mxs_dma_data dma_data;
+ int dma_channel_rx, dma_channel_tx;
+ int dma_irq_rx, dma_irq_tx;
+ int dma_channel;
+
+ struct scatterlist tx_sgl;
+ struct dma_chan *tx_dma_chan;
+ void *tx_dma_buf;
+
+ struct scatterlist rx_sgl;
+ struct dma_chan *rx_dma_chan;
+ void *rx_dma_buf;
};
static struct platform_device_id mxs_auart_devtype[] = {
@@ -155,14 +185,107 @@ static inline int is_imx28_auart(struct mxs_auart_port *s)
return s->devtype == IMX28_AUART;
}
+static inline bool auart_dma_enabled(struct mxs_auart_port *s)
+{
+ return s->flags & MXS_AUART_DMA_ENABLED;
+}
+
static void mxs_auart_stop_tx(struct uart_port *u);
#define to_auart_port(u) container_of(u, struct mxs_auart_port, port)
-static inline void mxs_auart_tx_chars(struct mxs_auart_port *s)
+static void mxs_auart_tx_chars(struct mxs_auart_port *s);
+
+static void dma_tx_callback(void *param)
{
+ struct mxs_auart_port *s = param;
struct circ_buf *xmit = &s->port.state->xmit;
+ dma_unmap_sg(s->dev, &s->tx_sgl, 1, DMA_TO_DEVICE);
+
+ /* clear the bit used to serialize the DMA tx. */
+ clear_bit(MXS_AUART_DMA_TX_SYNC, &s->flags);
+ smp_mb__after_clear_bit();
+
+ /* wake up the possible processes. */
+ if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
+ uart_write_wakeup(&s->port);
+
+ mxs_auart_tx_chars(s);
+}
+
+static int mxs_auart_dma_tx(struct mxs_auart_port *s, int size)
+{
+ struct dma_async_tx_descriptor *desc;
+ struct scatterlist *sgl = &s->tx_sgl;
+ struct dma_chan *channel = s->tx_dma_chan;
+ u32 pio;
+
+ /* [1] : send PIO. Note, the first pio word is CTRL1. */
+ pio = AUART_CTRL1_XFER_COUNT(size);
+ desc = dmaengine_prep_slave_sg(channel, (struct scatterlist *)&pio,
+ 1, DMA_TRANS_NONE, 0);
+ if (!desc) {
+ dev_err(s->dev, "step 1 error\n");
+ return -EINVAL;
+ }
+
+ /* [2] : set DMA buffer. */
+ sg_init_one(sgl, s->tx_dma_buf, size);
+ dma_map_sg(s->dev, sgl, 1, DMA_TO_DEVICE);
+ desc = dmaengine_prep_slave_sg(channel, sgl,
+ 1, DMA_MEM_TO_DEV, DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
+ if (!desc) {
+ dev_err(s->dev, "step 2 error\n");
+ return -EINVAL;
+ }
+
+ /* [3] : submit the DMA */
+ desc->callback = dma_tx_callback;
+ desc->callback_param = s;
+ dmaengine_submit(desc);
+ dma_async_issue_pending(channel);
+ return 0;
+}
+
+static void mxs_auart_tx_chars(struct mxs_auart_port *s)
+{
+ struct circ_buf *xmit = &s->port.state->xmit;
+
+ if (auart_dma_enabled(s)) {
+ int i = 0;
+ int size;
+ void *buffer = s->tx_dma_buf;
+
+ if (test_and_set_bit(MXS_AUART_DMA_TX_SYNC, &s->flags))
+ return;
+
+ while (!uart_circ_empty(xmit) && !uart_tx_stopped(&s->port)) {
+ size = min_t(u32, UART_XMIT_SIZE - i,
+ CIRC_CNT_TO_END(xmit->head,
+ xmit->tail,
+ UART_XMIT_SIZE));
+ memcpy(buffer + i, xmit->buf + xmit->tail, size);
+ xmit->tail = (xmit->tail + size) & (UART_XMIT_SIZE - 1);
+
+ i += size;
+ if (i >= UART_XMIT_SIZE)
+ break;
+ }
+
+ if (uart_tx_stopped(&s->port))
+ mxs_auart_stop_tx(&s->port);
+
+ if (i) {
+ mxs_auart_dma_tx(s, i);
+ } else {
+ clear_bit(MXS_AUART_DMA_TX_SYNC, &s->flags);
+ smp_mb__after_clear_bit();
+ }
+ return;
+ }
+
+
while (!(readl(s->port.membase + AUART_STAT) &
AUART_STAT_TXFF)) {
if (s->port.x_char) {
@@ -316,10 +439,157 @@ static u32 mxs_auart_get_mctrl(struct uart_port *u)
return mctrl;
}
+static bool mxs_auart_dma_filter(struct dma_chan *chan, void *param)
+{
+ struct mxs_auart_port *s = param;
+
+ if (!mxs_dma_is_apbx(chan))
+ return false;
+
+ if (s->dma_channel == chan->chan_id) {
+ chan->private = &s->dma_data;
+ return true;
+ }
+ return false;
+}
+
+static int mxs_auart_dma_prep_rx(struct mxs_auart_port *s);
+static void dma_rx_callback(void *arg)
+{
+ struct mxs_auart_port *s = (struct mxs_auart_port *) arg;
+ struct tty_struct *tty = s->port.state->port.tty;
+ int count;
+ u32 stat;
+
+ stat = readl(s->port.membase + AUART_STAT);
+ stat &= ~(AUART_STAT_OERR | AUART_STAT_BERR |
+ AUART_STAT_PERR | AUART_STAT_FERR);
+
+ count = stat & AUART_STAT_RXCOUNT_MASK;
+ tty_insert_flip_string(tty, s->rx_dma_buf, count);
+
+ writel(stat, s->port.membase + AUART_STAT);
+ tty_flip_buffer_push(tty);
+
+ /* start the next DMA for RX. */
+ mxs_auart_dma_prep_rx(s);
+}
+
+static int mxs_auart_dma_prep_rx(struct mxs_auart_port *s)
+{
+ struct dma_async_tx_descriptor *desc;
+ struct scatterlist *sgl = &s->rx_sgl;
+ struct dma_chan *channel = s->rx_dma_chan;
+ u32 pio[1];
+
+ /* [1] : send PIO */
+ pio[0] = AUART_CTRL0_RXTO_ENABLE
+ | AUART_CTRL0_RXTIMEOUT(0x80)
+ | AUART_CTRL0_XFER_COUNT(UART_XMIT_SIZE);
+ desc = dmaengine_prep_slave_sg(channel, (struct scatterlist *)pio,
+ 1, DMA_TRANS_NONE, 0);
+ if (!desc) {
+ dev_err(s->dev, "step 1 error\n");
+ return -EINVAL;
+ }
+
+ /* [2] : send DMA request */
+ sg_init_one(sgl, s->rx_dma_buf, UART_XMIT_SIZE);
+ dma_map_sg(s->dev, sgl, 1, DMA_FROM_DEVICE);
+ desc = dmaengine_prep_slave_sg(channel, sgl, 1, DMA_DEV_TO_MEM,
+ DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
+ if (!desc) {
+ dev_err(s->dev, "step 2 error\n");
+ return -1;
+ }
+
+ /* [3] : submit the DMA, but do not issue it. */
+ desc->callback = dma_rx_callback;
+ desc->callback_param = s;
+ dmaengine_submit(desc);
+ dma_async_issue_pending(channel);
+ return 0;
+}
+
+static void mxs_auart_dma_exit_channel(struct mxs_auart_port *s)
+{
+ if (s->tx_dma_chan) {
+ dma_release_channel(s->tx_dma_chan);
+ s->tx_dma_chan = NULL;
+ }
+ if (s->rx_dma_chan) {
+ dma_release_channel(s->rx_dma_chan);
+ s->rx_dma_chan = NULL;
+ }
+
+ kfree(s->tx_dma_buf);
+ kfree(s->rx_dma_buf);
+ s->tx_dma_buf = NULL;
+ s->rx_dma_buf = NULL;
+}
+
+static void mxs_auart_dma_exit(struct mxs_auart_port *s)
+{
+
+ writel(AUART_CTRL2_TXDMAE | AUART_CTRL2_RXDMAE | AUART_CTRL2_DMAONERR,
+ s->port.membase + AUART_CTRL2_CLR);
+
+ mxs_auart_dma_exit_channel(s);
+ s->flags &= ~MXS_AUART_DMA_ENABLED;
+ clear_bit(MXS_AUART_DMA_TX_SYNC, &s->flags);
+ clear_bit(MXS_AUART_DMA_RX_READY, &s->flags);
+}
+
+static int mxs_auart_dma_init(struct mxs_auart_port *s)
+{
+ dma_cap_mask_t mask;
+
+ if (auart_dma_enabled(s))
+ return 0;
+
+ /* We do not get the right DMA channels. */
+ if (s->dma_channel_rx == -1 || s->dma_channel_rx == -1)
+ return -EINVAL;
+
+ /* init for RX */
+ dma_cap_zero(mask);
+ dma_cap_set(DMA_SLAVE, mask);
+ s->dma_channel = s->dma_channel_rx;
+ s->dma_data.chan_irq = s->dma_irq_rx;
+ s->rx_dma_chan = dma_request_channel(mask, mxs_auart_dma_filter, s);
+ if (!s->rx_dma_chan)
+ goto err_out;
+ s->rx_dma_buf = kzalloc(UART_XMIT_SIZE, GFP_KERNEL | GFP_DMA);
+ if (!s->rx_dma_buf)
+ goto err_out;
+
+ /* init for TX */
+ s->dma_channel = s->dma_channel_tx;
+ s->dma_data.chan_irq = s->dma_irq_tx;
+ s->tx_dma_chan = dma_request_channel(mask, mxs_auart_dma_filter, s);
+ if (!s->tx_dma_chan)
+ goto err_out;
+ s->tx_dma_buf = kzalloc(UART_XMIT_SIZE, GFP_KERNEL | GFP_DMA);
+ if (!s->tx_dma_buf)
+ goto err_out;
+
+ /* set the flags */
+ s->flags |= MXS_AUART_DMA_ENABLED;
+ dev_dbg(s->dev, "enabled the DMA support.");
+
+ return 0;
+
+err_out:
+ mxs_auart_dma_exit_channel(s);
+ return -EINVAL;
+
+}
+
static void mxs_auart_settermios(struct uart_port *u,
struct ktermios *termios,
struct ktermios *old)
{
+ struct mxs_auart_port *s = to_auart_port(u);
u32 bm, ctrl, ctrl2, div;
unsigned int cflag, baud;
@@ -391,10 +661,23 @@ static void mxs_auart_settermios(struct uart_port *u,
ctrl |= AUART_LINECTRL_STP2;
/* figure out the hardware flow control settings */
- if (cflag & CRTSCTS)
+ if (cflag & CRTSCTS) {
+ /*
+ * The DMA has a bug(see errata:2836) in mx23.
+ * So we can not implement the DMA for auart in mx23,
+ * we can only implement the DMA support for auart
+ * in mx28.
+ */
+ if (is_imx28_auart(s) && (s->flags & MXS_AUART_DMA_CONFIG)) {
+ if (!mxs_auart_dma_init(s))
+ /* enable DMA tranfer */
+ ctrl2 |= AUART_CTRL2_TXDMAE | AUART_CTRL2_RXDMAE
+ | AUART_CTRL2_DMAONERR;
+ }
ctrl2 |= AUART_CTRL2_CTSEN | AUART_CTRL2_RTSEN;
- else
+ } else {
ctrl2 &= ~(AUART_CTRL2_CTSEN | AUART_CTRL2_RTSEN);
+ }
/* set baud rate */
baud = uart_get_baud_rate(u, termios, old, 0, u->uartclk);
@@ -406,6 +689,18 @@ static void mxs_auart_settermios(struct uart_port *u,
writel(ctrl2, u->membase + AUART_CTRL2);
uart_update_timeout(u, termios->c_cflag, baud);
+
+ /* prepare for the DMA RX. */
+ if (auart_dma_enabled(s) &&
+ !test_and_set_bit(MXS_AUART_DMA_RX_READY, &s->flags)) {
+ if (!mxs_auart_dma_prep_rx(s)) {
+ /* Disable the normal RX interrupt. */
+ writel(AUART_INTR_RXIEN, u->membase + AUART_INTR_CLR);
+ } else {
+ mxs_auart_dma_exit(s);
+ dev_err(s->dev, "We can not start up the DMA.\n");
+ }
+ }
}
static irqreturn_t mxs_auart_irq_handle(int irq, void *context)
@@ -484,6 +779,9 @@ static void mxs_auart_shutdown(struct uart_port *u)
{
struct mxs_auart_port *s = to_auart_port(u);
+ if (auart_dma_enabled(s))
+ mxs_auart_dma_exit(s);
+
writel(AUART_CTRL2_UARTEN, u->membase + AUART_CTRL2_CLR);
writel(AUART_INTR_RXIEN | AUART_INTR_RTIEN | AUART_INTR_CTSMIEN,
@@ -717,6 +1015,7 @@ static int serial_mxs_probe_dt(struct mxs_auart_port *s,
struct platform_device *pdev)
{
struct device_node *np = pdev->dev.of_node;
+ u32 dma_channel[2];
int ret;
if (!np)
@@ -730,6 +1029,20 @@ static int serial_mxs_probe_dt(struct mxs_auart_port *s,
}
s->port.line = ret;
+ s->dma_irq_rx = platform_get_irq(pdev, 1);
+ s->dma_irq_tx = platform_get_irq(pdev, 2);
+
+ ret = of_property_read_u32_array(np, "fsl,auart-dma-channel",
+ dma_channel, 2);
+ if (ret == 0) {
+ s->dma_channel_rx = dma_channel[0];
+ s->dma_channel_tx = dma_channel[1];
+
+ s->flags |= MXS_AUART_DMA_CONFIG;
+ } else {
+ s->dma_channel_rx = -1;
+ s->dma_channel_tx = -1;
+ }
return 0;
}
@@ -787,7 +1100,6 @@ static int __devinit mxs_auart_probe(struct platform_device *pdev)
s->port.type = PORT_IMX;
s->port.dev = s->dev = get_device(&pdev->dev);
- s->flags = 0;
s->ctrl = 0;
s->irq = platform_get_irq(pdev, 0);
Only we meet the following conditions, we can enable the DMA support for auart: (1) We enable the DMA support in the dts file, such as arch/arm/boot/dts/imx28.dtsi. (2) We enable the hardware flow control. (3) We use the mx28, not the mx23. Due to hardware bug(see errata: 2836), we can not add the DMA support to mx23. Signed-off-by: Huang Shijie <b32955@freescale.com> --- .../bindings/tty/serial/fsl-mxs-auart.txt | 8 + drivers/tty/serial/mxs-auart.c | 322 +++++++++++++++++++- 2 files changed, 325 insertions(+), 5 deletions(-)