@@ -346,6 +346,21 @@ config AB8500_BM
help
Say Y to include support for AB8500 battery management.
+config CHARGER_PM2301
+ bool "PM2301 Battery Charger Driver"
+ depends on AB8500_BM
+ help
+ Say Y to include support for PM2301 charger driver.
+
+config PM2XXX_DEEP_DEBUG
+ bool "PM2XXX Deep Debug"
+ depends on DEEP_DEBUG && CHARGER_PM2301
+ default n
+ help
+ Deep Debug interface provides an access to all registers.
+ It allows to read or write directly a register.
+ Say Y to include support for Deep Debug.
+ If unsure, say N.
endif # POWER_SUPPLY
source "drivers/power/avs/Kconfig"
@@ -46,6 +46,7 @@ obj-$(CONFIG_CHARGER_LP8727) += lp8727_charger.o
obj-$(CONFIG_CHARGER_LP8788) += lp8788-charger.o
obj-$(CONFIG_CHARGER_GPIO) += gpio-charger.o
obj-$(CONFIG_CHARGER_MANAGER) += charger-manager.o
+obj-$(CONFIG_CHARGER_PM2301) += pm2301_charger.o
obj-$(CONFIG_CHARGER_MAX8997) += max8997_charger.o
obj-$(CONFIG_CHARGER_MAX8998) += max8998_charger.o
obj-$(CONFIG_CHARGER_BQ2415X) += bq2415x_charger.o
@@ -2795,7 +2795,9 @@ static int __devexit ab8500_charger_remove(struct platform_device *pdev)
flush_scheduled_work();
power_supply_unregister(&di->usb_chg.psy);
+#if !defined(CONFIG_CHARGER_PM2301)
power_supply_unregister(&di->ac_chg.psy);
+#endif
platform_set_drvdata(pdev, NULL);
return 0;
@@ -2954,14 +2956,14 @@ static int __devinit ab8500_charger_probe(struct platform_device *pdev)
dev_err(di->dev, "failed to initialize ABB registers\n");
goto free_regulator;
}
-
+#if !defined(CONFIG_CHARGER_PM2301)
/* Register AC charger class */
ret = power_supply_register(di->dev, &di->ac_chg.psy);
if (ret) {
dev_err(di->dev, "failed to register AC charger\n");
goto free_regulator;
}
-
+#endif
/* Register USB charger class */
ret = power_supply_register(di->dev, &di->usb_chg.psy);
if (ret) {
@@ -3048,7 +3050,9 @@ put_usb_phy:
free_usb:
power_supply_unregister(&di->usb_chg.psy);
free_ac:
+#if !defined(CONFIG_CHARGER_PM2301)
power_supply_unregister(&di->ac_chg.psy);
+#endif
free_regulator:
regulator_put(di->regu);
free_charger_wq:
new file mode 100644
@@ -0,0 +1,1599 @@
+/*
+ * Power supply driver for ST Ericsson pm2xxx_charger charger
+ *
+ * Copyright 2012 ST Ericsson.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/device.h>
+#include <linux/interrupt.h>
+#include <linux/delay.h>
+#include <linux/slab.h>
+#include <linux/platform_device.h>
+#include <linux/power_supply.h>
+#include <linux/completion.h>
+#include <linux/regulator/consumer.h>
+#include <linux/err.h>
+#include <linux/i2c.h>
+#include <linux/workqueue.h>
+#include <linux/kobject.h>
+#include <linux/mfd/ab8500.h>
+#include <linux/mfd/abx500.h>
+#include <linux/mfd/abx500/ab8500-bm.h>
+#include <linux/mfd/abx500/ab8500-gpadc.h>
+#include <linux/mfd/abx500/ux500_chargalg.h>
+#include <linux/pm2301_charger.h>
+
+#ifdef CONFIG_PM2XXX_DEEP_DEBUG
+#include <linux/debugfs.h>
+#include <linux/ux500_deepdebug.h>
+#endif
+
+#define MAIN_WDOG_ENA 0x01
+#define MAIN_WDOG_KICK 0x02
+#define MAIN_WDOG_DIS 0x00
+#define CHARG_WD_KICK 0x01
+#define MAIN_CH_ENA 0x01
+#define MAIN_CH_NO_OVERSHOOT_ENA_N 0x02
+#define MAIN_CH_DET 0x01
+#define MAIN_CH_CV_ON 0x04
+#define OTP_ENABLE_WD 0x01
+
+#define MAIN_CH_INPUT_CURR_SHIFT 4
+
+#define LED_INDICATOR_PWM_ENA 0x01
+#define LED_INDICATOR_PWM_DIS 0x00
+#define LED_IND_CUR_5MA 0x04
+#define LED_INDICATOR_PWM_DUTY_252_256 0xBF
+
+/* HW failure constants */
+#define MAIN_CH_TH_PROT 0x02
+#define MAIN_CH_NOK 0x01
+
+/* Watchdog timeout constant */
+#define WD_TIMER 0x30 /* 4min */
+#define WD_KICK_INTERVAL (60 * HZ)
+
+/* Lowest charger voltage is 3.39V -> 0x4E */
+#define LOW_VOLT_REG 0x4E
+
+#define PM2XXX_BATT_CTRL_REG1 0x00
+#define PM2XXX_BATT_CTRL_REG2 0x01
+#define PM2XXX_BATT_CTRL_REG3 0x02
+#define PM2XXX_BATT_CTRL_REG4 0x03
+#define PM2XXX_BATT_CTRL_REG5 0x04
+#define PM2XXX_BATT_CTRL_REG6 0x05
+#define PM2XXX_BATT_CTRL_REG7 0x06
+#define PM2XXX_BATT_CTRL_REG8 0x07
+#define PM2XXX_NTC_CTRL_REG1 0x08
+#define PM2XXX_NTC_CTRL_REG2 0x09
+#define PM2XXX_BATT_CTRL_REG9 0x0A
+#define PM2XXX_BATT_STAT_REG1 0x0B
+#define PM2XXX_INP_VOLT_VPWR2 0x11
+#define PM2XXX_INP_DROP_VPWR2 0x13
+#define PM2XXX_INP_VOLT_VPWR1 0x15
+#define PM2XXX_INP_DROP_VPWR1 0x17
+#define PM2XXX_INP_MODE_VPWR 0x18
+#define PM2XXX_BATT_WD_KICK 0x70
+#define PM2XXX_DEV_VER_STAT 0x0C
+#define PM2XXX_THERM_WARN_CTRL_REG 0x20
+#define PM2XXX_BATT_DISC_REG 0x21
+#define PM2XXX_BATT_LOW_LEV_COMP_REG 0x22
+#define PM2XXX_BATT_LOW_LEV_VAL_REG 0x23
+#define PM2XXX_I2C_PAD_CTRL_REG 0x24
+#define PM2XXX_SW_CTRL_REG 0x26
+#define PM2XXX_LED_CTRL_REG 0x28
+
+#define PM2XXX_REG_INT1 0x40
+#define PM2XXX_MASK_REG_INT1 0x50
+#define PM2XXX_SRCE_REG_INT1 0x60
+#define PM2XXX_REG_INT2 0x41
+#define PM2XXX_MASK_REG_INT2 0x51
+#define PM2XXX_SRCE_REG_INT2 0x61
+#define PM2XXX_REG_INT3 0x42
+#define PM2XXX_MASK_REG_INT3 0x52
+#define PM2XXX_SRCE_REG_INT3 0x62
+#define PM2XXX_REG_INT4 0x43
+#define PM2XXX_MASK_REG_INT4 0x53
+#define PM2XXX_SRCE_REG_INT4 0x63
+#define PM2XXX_REG_INT5 0x44
+#define PM2XXX_MASK_REG_INT5 0x54
+#define PM2XXX_SRCE_REG_INT5 0x64
+#define PM2XXX_REG_INT6 0x45
+#define PM2XXX_MASK_REG_INT6 0x55
+#define PM2XXX_SRCE_REG_INT6 0x65
+
+#define VPWR_OVV 0x0
+#define VSYSTEM_OVV 0x1
+
+/* control Reg 1 */
+#define PM2XXX_CH_RESUME_EN 0x1
+#define PM2XXX_CH_RESUME_DIS 0x0
+
+/* control Reg 2 */
+#define PM2XXX_CH_AUTO_RESUME_EN 0X2
+#define PM2XXX_CH_AUTO_RESUME_DIS 0X0
+#define PM2XXX_CHARGER_ENA 0x4
+#define PM2XXX_CHARGER_DIS 0x0
+
+/* control Reg 3 */
+#define PM2XXX_CH_WD_CC_PHASE_OFF 0x0
+#define PM2XXX_CH_WD_CC_PHASE_5MIN 0x1
+#define PM2XXX_CH_WD_CC_PHASE_10MIN 0x2
+#define PM2XXX_CH_WD_CC_PHASE_30MIN 0x3
+#define PM2XXX_CH_WD_CC_PHASE_60MIN 0x4
+#define PM2XXX_CH_WD_CC_PHASE_120MIN 0x5
+#define PM2XXX_CH_WD_CC_PHASE_240MIN 0x6
+#define PM2XXX_CH_WD_CC_PHASE_360MIN 0x7
+
+#define PM2XXX_CH_WD_CV_PHASE_OFF (0x0<<3)
+#define PM2XXX_CH_WD_CV_PHASE_5MIN (0x1<<3)
+#define PM2XXX_CH_WD_CV_PHASE_10MIN (0x2<<3)
+#define PM2XXX_CH_WD_CV_PHASE_30MIN (0x3<<3)
+#define PM2XXX_CH_WD_CV_PHASE_60MIN (0x4<<3)
+#define PM2XXX_CH_WD_CV_PHASE_120MIN (0x5<<3)
+#define PM2XXX_CH_WD_CV_PHASE_240MIN (0x6<<3)
+#define PM2XXX_CH_WD_CV_PHASE_360MIN (0x7<<3)
+
+/* control Reg 4 */
+#define PM2XXX_CH_WD_PRECH_PHASE_OFF 0x0
+#define PM2XXX_CH_WD_PRECH_PHASE_1MIN 0x1
+#define PM2XXX_CH_WD_PRECH_PHASE_5MIN 0x2
+#define PM2XXX_CH_WD_PRECH_PHASE_10MIN 0x3
+#define PM2XXX_CH_WD_PRECH_PHASE_30MIN 0x4
+#define PM2XXX_CH_WD_PRECH_PHASE_60MIN 0x5
+#define PM2XXX_CH_WD_PRECH_PHASE_120MIN 0x6
+#define PM2XXX_CH_WD_PRECH_PHASE_240MIN 0x7
+
+/* control Reg 5 */
+#define PM2XXX_CH_WD_AUTO_TIMEOUT_NONE 0x0
+#define PM2XXX_CH_WD_AUTO_TIMEOUT_20MIN 0x1
+
+/* control Reg 6 */
+#define PM2XXX_DIR_CH_CC_CURRENT_200MA 0x0
+#define PM2XXX_DIR_CH_CC_CURRENT_400MA 0x2
+#define PM2XXX_DIR_CH_CC_CURRENT_600MA 0x3
+#define PM2XXX_DIR_CH_CC_CURRENT_800MA 0x4
+#define PM2XXX_DIR_CH_CC_CURRENT_1000MA 0x5
+#define PM2XXX_DIR_CH_CC_CURRENT_1200MA 0x6
+#define PM2XXX_DIR_CH_CC_CURRENT_1400MA 0x7
+#define PM2XXX_DIR_CH_CC_CURRENT_1600MA 0x8
+#define PM2XXX_DIR_CH_CC_CURRENT_1800MA 0x9
+#define PM2XXX_DIR_CH_CC_CURRENT_2000MA 0xA
+#define PM2XXX_DIR_CH_CC_CURRENT_2200MA 0xB
+#define PM2XXX_DIR_CH_CC_CURRENT_2400MA 0xC
+#define PM2XXX_DIR_CH_CC_CURRENT_2600MA 0xD
+#define PM2XXX_DIR_CH_CC_CURRENT_2800MA 0xE
+#define PM2XXX_DIR_CH_CC_CURRENT_3000MA 0xF
+
+#define PM2XXX_CH_PRECH_CURRENT_25MA (0x0<<4)
+#define PM2XXX_CH_PRECH_CURRENT_50MA (0x1<<4)
+#define PM2XXX_CH_PRECH_CURRENT_75MA (0x2<<4)
+#define PM2XXX_CH_PRECH_CURRENT_100MA (0x3<<4)
+
+#define PM2XXX_CH_EOC_CURRENT_100MA (0x0<<6)
+#define PM2XXX_CH_EOC_CURRENT_150MA (0x1<<6)
+#define PM2XXX_CH_EOC_CURRENT_300MA (0x2<<6)
+#define PM2XXX_CH_EOC_CURRENT_400MA (0x3<<6)
+
+/* control Reg 7 */
+#define PM2XXX_CH_PRECH_VOL_2_5 0x0
+#define PM2XXX_CH_PRECH_VOL_2_7 0x1
+#define PM2XXX_CH_PRECH_VOL_2_9 0x2
+#define PM2XXX_CH_PRECH_VOL_3_1 0x3
+
+#define PM2XXX_CH_VRESUME_VOL_3_2 (0x0<<2)
+#define PM2XXX_CH_VRESUME_VOL_3_4 (0x1<<2)
+#define PM2XXX_CH_VRESUME_VOL_3_6 (0x2<<2)
+#define PM2XXX_CH_VRESUME_VOL_3_8 (0x3<<2)
+
+/* control Reg 8 */
+#define PM2XXX_CH_VOLT_3_5 0x0
+#define PM2XXX_CH_VOLT_3_5225 0x1
+#define PM2XXX_CH_VOLT_3_6 0x4
+#define PM2XXX_CH_VOLT_3_7 0x8
+#define PM2XXX_CH_VOLT_4_0 0x14
+#define PM2XXX_CH_VOLT_4_175 0x1B
+#define PM2XXX_CH_VOLT_4_2 0x1C
+#define PM2XXX_CH_VOLT_4_275 0x1F
+#define PM2XXX_CH_VOLT_4_3 0x20
+
+/*NTC control register 1*/
+#define PM2XXX_BTEMP_HIGH_TH_45 0x0
+#define PM2XXX_BTEMP_HIGH_TH_50 0x1
+#define PM2XXX_BTEMP_HIGH_TH_55 0x2
+#define PM2XXX_BTEMP_HIGH_TH_60 0x3
+#define PM2XXX_BTEMP_HIGH_TH_65 0x4
+
+#define PM2XXX_BTEMP_LOW_TH_N5 (0x0<<3)
+#define PM2XXX_BTEMP_LOW_TH_0 (0x1<<3)
+#define PM2XXX_BTEMP_LOW_TH_5 (0x2<<3)
+#define PM2XXX_BTEMP_LOW_TH_10 (0x3<<3)
+
+/*NTC control register 2*/
+#define PM2XXX_NTC_BETA_COEFF_3477 0x0
+#define PM2XXX_NTC_BETA_COEFF_3964 0x1
+
+#define PM2XXX_NTC_RES_10K (0x0<<2)
+#define PM2XXX_NTC_RES_47K (0x1<<2)
+#define PM2XXX_NTC_RES_100K (0x2<<2)
+#define PM2XXX_NTC_RES_NO_NTC (0x3<<2)
+
+/* control Reg 9 */
+#define PM2XXX_CH_CC_MODEDROP_EN 1
+#define PM2XXX_CH_CC_MODEDROP_DIS 0
+
+#define PM2XXX_CH_CC_REDUCED_CURRENT_100MA (0x0<<1)
+#define PM2XXX_CH_CC_REDUCED_CURRENT_200MA (0x1<<1)
+#define PM2XXX_CH_CC_REDUCED_CURRENT_400MA (0x2<<1)
+#define PM2XXX_CH_CC_REDUCED_CURRENT_IDENT (0x3<<1)
+
+#define PM2XXX_CHARCHING_INFO_DIS (0<<3)
+#define PM2XXX_CHARCHING_INFO_EN (1<<3)
+
+#define PM2XXX_CH_150MV_DROP_300MV (0<<4)
+#define PM2XXX_CH_150MV_DROP_150MV (1<<4)
+
+
+/* charger status register */
+#define PM2XXX_CHG_STATUS_OFF 0x0
+#define PM2XXX_CHG_STATUS_ON 0x1
+#define PM2XXX_CHG_STATUS_FULL 0x2
+#define PM2XXX_CHG_STATUS_ERR 0x3
+#define PM2XXX_CHG_STATUS_WAIT 0x4
+#define PM2XXX_CHG_STATUS_NOBAT 0x5
+
+/* Input charger voltage VPWR2 */
+#define PM2XXX_VPWR2_OVV_6_0 0x0
+#define PM2XXX_VPWR2_OVV_6_3 0x1
+#define PM2XXX_VPWR2_OVV_10 0x2
+#define PM2XXX_VPWR2_OVV_NONE 0x3
+
+/* Input charger voltage VPWR1 */
+#define PM2XXX_VPWR1_OVV_6_0 0x0
+#define PM2XXX_VPWR1_OVV_6_3 0x1
+#define PM2XXX_VPWR1_OVV_10 0x2
+#define PM2XXX_VPWR1_OVV_NONE 0x3
+
+/* Battery low level comparator control register */
+#define PM2XXX_VBAT_LOW_MONITORING_DIS 0x0
+#define PM2XXX_VBAT_LOW_MONITORING_ENA 0x1
+
+/* Battery low level value control register */
+#define PM2XXX_VBAT_LOW_LEVEL_2_3 0x0
+#define PM2XXX_VBAT_LOW_LEVEL_2_4 0x1
+#define PM2XXX_VBAT_LOW_LEVEL_2_5 0x2
+#define PM2XXX_VBAT_LOW_LEVEL_2_6 0x3
+#define PM2XXX_VBAT_LOW_LEVEL_2_7 0x4
+#define PM2XXX_VBAT_LOW_LEVEL_2_8 0x5
+#define PM2XXX_VBAT_LOW_LEVEL_2_9 0x6
+#define PM2XXX_VBAT_LOW_LEVEL_3_0 0x7
+#define PM2XXX_VBAT_LOW_LEVEL_3_1 0x8
+#define PM2XXX_VBAT_LOW_LEVEL_3_2 0x9
+#define PM2XXX_VBAT_LOW_LEVEL_3_3 0xA
+#define PM2XXX_VBAT_LOW_LEVEL_3_4 0xB
+#define PM2XXX_VBAT_LOW_LEVEL_3_5 0xC
+#define PM2XXX_VBAT_LOW_LEVEL_3_6 0xD
+#define PM2XXX_VBAT_LOW_LEVEL_3_7 0xE
+#define PM2XXX_VBAT_LOW_LEVEL_3_8 0xF
+#define PM2XXX_VBAT_LOW_LEVEL_3_9 0x10
+#define PM2XXX_VBAT_LOW_LEVEL_4_0 0x11
+#define PM2XXX_VBAT_LOW_LEVEL_4_1 0x12
+#define PM2XXX_VBAT_LOW_LEVEL_4_2 0x13
+
+/* SW CTRL */
+#define PM2XXX_SWCTRL_HW 0x0
+#define PM2XXX_SWCTRL_SW 0x1
+
+
+/* LED Driver Control */
+#define PM2XXX_LED_CURRENT_2_5MA (0X0<<2)
+#define PM2XXX_LED_CURRENT_1MA (0X1<<2)
+#define PM2XXX_LED_CURRENT_5MA (0X2<<2)
+#define PM2XXX_LED_CURRENT_10MA (0X3<<2)
+
+#define PM2XXX_LED_SELECT_EN (0X0<<1)
+#define PM2XXX_LED_SELECT_DIS (0X1<<1)
+
+#define PM2XXX_ANTI_OVERSHOOT_DIS 0X0
+#define PM2XXX_ANTI_OVERSHOOT_EN 0X1
+
+#define to_pm2xxx_charger_ac_device_info(x) container_of((x), \
+ struct pm2xxx_charger, ac_chg)
+
+static int pm2xxx_interrupt_registers[] = {
+ PM2XXX_REG_INT1 ,
+ PM2XXX_REG_INT2 ,
+ PM2XXX_REG_INT3 ,
+ PM2XXX_REG_INT4 ,
+ PM2XXX_REG_INT5 ,
+ PM2XXX_REG_INT6 ,
+};
+
+enum pm2xxx_reg_int1 {
+ PM2XXX_INT1_ITVBATDISCONNECT = 0x02,
+ PM2XXX_INT1_ITVBATLOWR = 0x04,
+ PM2XXX_INT1_ITVBATLOWF = 0x08,
+};
+
+enum pm2xxx_mask_reg_int1 {
+ PM2XXX_INT1_M_ITVBATDISCONNECT = 0x02,
+ PM2XXX_INT1_M_ITVBATLOWR = 0x04,
+ PM2XXX_INT1_M_ITVBATLOWF = 0x08,
+};
+
+enum pm2xxx_source_reg_int1 {
+ PM2XXX_INT1_S_ITVBATDISCONNECT = 0x02,
+ PM2XXX_INT1_S_ITVBATLOWR = 0x04,
+ PM2XXX_INT1_S_ITVBATLOWF = 0x08,
+};
+
+enum pm2xxx_reg_int2 {
+ PM2XXX_INT2_ITVPWR2PLUG = 0x01,
+ PM2XXX_INT2_ITVPWR2UNPLUG = 0x02,
+ PM2XXX_INT2_ITVPWR1PLUG = 0x04,
+ PM2XXX_INT2_ITVPWR1UNPLUG = 0x08,
+};
+
+enum pm2xxx_mask_reg_int2 {
+ PM2XXX_INT2_M_ITVPWR2PLUG = 0x01,
+ PM2XXX_INT2_M_ITVPWR2UNPLUG = 0x02,
+ PM2XXX_INT2_M_ITVPWR1PLUG = 0x04,
+ PM2XXX_INT2_M_ITVPWR1UNPLUG = 0x08,
+};
+
+enum pm2xxx_source_reg_int2 {
+ PM2XXX_INT2_S_ITVPWR2PLUG = 0x03,
+ PM2XXX_INT2_S_ITVPWR1PLUG = 0x0c,
+};
+
+enum pm2xxx_reg_int3 {
+ PM2XXX_INT3_ITCHPRECHARGEWD = 0x01,
+ PM2XXX_INT3_ITCHCCWD = 0x02,
+ PM2XXX_INT3_ITCHCVWD = 0x04,
+ PM2XXX_INT3_ITAUTOTIMEOUTWD = 0x08,
+};
+
+enum pm2xxx_mask_reg_int3 {
+ PM2XXX_INT3_M_ITCHPRECHARGEWD = 0x01,
+ PM2XXX_INT3_M_ITCHCCWD = 0x02,
+ PM2XXX_INT3_M_ITCHCVWD = 0x04,
+ PM2XXX_INT3_M_ITAUTOTIMEOUTWD = 0x08,
+};
+
+enum pm2xxx_source_reg_int3 {
+ PM2XXX_INT3_S_ITCHPRECHARGEWD = 0x01,
+ PM2XXX_INT3_S_ITCHCCWD = 0x02,
+ PM2XXX_INT3_S_ITCHCVWD = 0x04,
+ PM2XXX_INT3_S_ITAUTOTIMEOUTWD = 0x08,
+};
+
+enum pm2xxx_reg_int4 {
+ PM2XXX_INT4_ITBATTEMPCOLD = 0x01,
+ PM2XXX_INT4_ITBATTEMPHOT = 0x02,
+ PM2XXX_INT4_ITVPWR2OVV = 0x04,
+ PM2XXX_INT4_ITVPWR1OVV = 0x08,
+ PM2XXX_INT4_ITCHARGINGON = 0x10,
+ PM2XXX_INT4_ITVRESUME = 0x20,
+ PM2XXX_INT4_ITBATTFULL = 0x40,
+ PM2XXX_INT4_ITCVPHASE = 0x80,
+};
+
+enum pm2xxx_mask_reg_int4 {
+ PM2XXX_INT4_M_ITBATTEMPCOLD = 0x01,
+ PM2XXX_INT4_M_ITBATTEMPHOT = 0x02,
+ PM2XXX_INT4_M_ITVPWR2OVV = 0x04,
+ PM2XXX_INT4_M_ITVPWR1OVV = 0x08,
+ PM2XXX_INT4_M_ITCHARGINGON = 0x10,
+ PM2XXX_INT4_M_ITVRESUME = 0x20,
+ PM2XXX_INT4_M_ITBATTFULL = 0x40,
+ PM2XXX_INT4_M_ITCVPHASE = 0x80,
+};
+
+enum pm2xxx_source_reg_int4 {
+ PM2XXX_INT4_S_ITBATTEMPCOLD = 0x01,
+ PM2XXX_INT4_S_ITBATTEMPHOT = 0x02,
+ PM2XXX_INT4_S_ITVPWR2OVV = 0x04,
+ PM2XXX_INT4_S_ITVPWR1OVV = 0x08,
+ PM2XXX_INT4_S_ITCHARGINGON = 0x10,
+ PM2XXX_INT4_S_ITVRESUME = 0x20,
+ PM2XXX_INT4_S_ITBATTFULL = 0x40,
+ PM2XXX_INT4_S_ITCVPHASE = 0x80,
+};
+
+enum pm2xxx_reg_int5 {
+ PM2XXX_INT5_ITTHERMALSHUTDOWNRISE = 0x01,
+ PM2XXX_INT5_ITTHERMALSHUTDOWNFALL = 0x02,
+ PM2XXX_INT5_ITTHERMALWARNINGRISE = 0x04,
+ PM2XXX_INT5_ITTHERMALWARNINGFALL = 0x08,
+ PM2XXX_INT5_ITVSYSTEMOVV = 0x10,
+};
+
+enum pm2xxx_mask_reg_int5 {
+ PM2XXX_INT5_M_ITTHERMALSHUTDOWNRISE = 0x01,
+ PM2XXX_INT5_M_ITTHERMALSHUTDOWNFALL = 0x02,
+ PM2XXX_INT5_M_ITTHERMALWARNINGRISE = 0x04,
+ PM2XXX_INT5_M_ITTHERMALWARNINGFALL = 0x08,
+ PM2XXX_INT5_M_ITVSYSTEMOVV = 0x10,
+};
+
+enum pm2xxx_source_reg_int5 {
+ PM2XXX_INT5_S_ITTHERMALSHUTDOWNRISE = 0x01,
+ PM2XXX_INT5_S_ITTHERMALSHUTDOWNFALL = 0x02,
+ PM2XXX_INT5_S_ITTHERMALWARNINGRISE = 0x04,
+ PM2XXX_INT5_S_ITTHERMALWARNINGFALL = 0x08,
+ PM2XXX_INT5_S_ITVSYSTEMOVV = 0x10,
+};
+
+enum pm2xxx_reg_int6 {
+ PM2XXX_INT6_ITVPWR2DROP = 0x01,
+ PM2XXX_INT6_ITVPWR1DROP = 0x02,
+ PM2XXX_INT6_ITVPWR2VALIDRISE = 0x04,
+ PM2XXX_INT6_ITVPWR2VALIDFALL = 0x08,
+ PM2XXX_INT6_ITVPWR1VALIDRISE = 0x10,
+ PM2XXX_INT6_ITVPWR1VALIDFALL = 0x20,
+};
+
+enum pm2xxx_mask_reg_int6 {
+ PM2XXX_INT6_M_ITVPWR2DROP = 0x01,
+ PM2XXX_INT6_M_ITVPWR1DROP = 0x02,
+ PM2XXX_INT6_M_ITVPWR2VALIDRISE = 0x04,
+ PM2XXX_INT6_M_ITVPWR2VALIDFALL = 0x08,
+ PM2XXX_INT6_M_ITVPWR1VALIDRISE = 0x10,
+ PM2XXX_INT6_M_ITVPWR1VALIDFALL = 0x20,
+};
+
+enum pm2xxx_source_reg_int6 {
+ PM2XXX_INT6_S_ITVPWR2DROP = 0x01,
+ PM2XXX_INT6_S_ITVPWR1DROP = 0x02,
+ PM2XXX_INT6_S_ITVPWR2VALIDRISE = 0x04,
+ PM2XXX_INT6_S_ITVPWR2VALIDFALL = 0x08,
+ PM2XXX_INT6_S_ITVPWR1VALIDRISE = 0x10,
+ PM2XXX_INT6_S_ITVPWR1VALIDFALL = 0x20,
+};
+
+static enum power_supply_property pm2xxx_charger_ac_props[] = {
+ POWER_SUPPLY_PROP_HEALTH,
+ POWER_SUPPLY_PROP_PRESENT,
+ POWER_SUPPLY_PROP_ONLINE,
+ POWER_SUPPLY_PROP_VOLTAGE_NOW,
+ POWER_SUPPLY_PROP_VOLTAGE_AVG,
+ POWER_SUPPLY_PROP_CURRENT_NOW,
+};
+
+static int pm2xxx_charger_voltage_map[] = {
+ 3500 ,
+ 3525 ,
+ 3550 ,
+ 3575 ,
+ 3600 ,
+ 3625 ,
+ 3650 ,
+ 3675 ,
+ 3700 ,
+ 3725 ,
+ 3750 ,
+ 3775 ,
+ 3800 ,
+ 3825 ,
+ 3850 ,
+ 3875 ,
+ 3900 ,
+ 3925 ,
+ 3950 ,
+ 3975 ,
+ 4000 ,
+ 4025 ,
+ 4050 ,
+ 4075 ,
+ 4100 ,
+ 4125 ,
+ 4150 ,
+ 4175 ,
+ 4200 ,
+ 4225 ,
+ 4250 ,
+ 4275 ,
+ 4300 ,
+};
+
+static int pm2xxx_charger_current_map[] = {
+ 200 ,
+ 200 ,
+ 400 ,
+ 600 ,
+ 800 ,
+ 1000 ,
+ 1200 ,
+ 1400 ,
+ 1600 ,
+ 1800 ,
+ 2000 ,
+ 2200 ,
+ 2400 ,
+ 2600 ,
+ 2800 ,
+ 3000 ,
+};
+
+#ifdef CONFIG_PM2XXX_DEEP_DEBUG
+/* PM2XXX registers list */
+static struct ddbg_register ddbg_pm2xxx_registers[] = {
+ DDBG_REG("PM2XXX_BATT_CTRL_REG1", PM2XXX_BATT_CTRL_REG1, DDBG_RW),
+ DDBG_REG("PM2XXX_BATT_CTRL_REG2", PM2XXX_BATT_CTRL_REG2, DDBG_RW),
+ DDBG_REG("PM2XXX_BATT_CTRL_REG3", PM2XXX_BATT_CTRL_REG3, DDBG_RW),
+ DDBG_REG("PM2XXX_BATT_CTRL_REG4", PM2XXX_BATT_CTRL_REG4, DDBG_RW),
+ DDBG_REG("PM2XXX_BATT_CTRL_REG5", PM2XXX_BATT_CTRL_REG5, DDBG_RW),
+ DDBG_REG("PM2XXX_BATT_CTRL_REG6", PM2XXX_BATT_CTRL_REG6, DDBG_RW),
+ DDBG_REG("PM2XXX_BATT_CTRL_REG7", PM2XXX_BATT_CTRL_REG7, DDBG_RW),
+ DDBG_REG("PM2XXX_BATT_CTRL_REG8", PM2XXX_BATT_CTRL_REG8, DDBG_RW),
+ DDBG_REG("PM2XXX_NTC_CTRL_REG1", PM2XXX_NTC_CTRL_REG1, DDBG_RW),
+ DDBG_REG("PM2XXX_NTC_CTRL_REG2", PM2XXX_NTC_CTRL_REG2, DDBG_RW),
+ DDBG_REG("PM2XXX_BATT_CTRL_REG9", PM2XXX_BATT_CTRL_REG9, DDBG_RW),
+ DDBG_REG("PM2XXX_BATT_STAT_REG1", PM2XXX_BATT_STAT_REG1, DDBG_RO),
+ DDBG_REG("PM2XXX_INP_VOLT_VPWR2", PM2XXX_INP_VOLT_VPWR2, DDBG_RW),
+ DDBG_REG("PM2XXX_INP_DROP_VPWR2", PM2XXX_INP_DROP_VPWR2, DDBG_RW),
+ DDBG_REG("PM2XXX_INP_VOLT_VPWR1", PM2XXX_INP_VOLT_VPWR1, DDBG_RW),
+ DDBG_REG("PM2XXX_INP_DROP_VPWR1", PM2XXX_INP_DROP_VPWR1, DDBG_RW),
+ DDBG_REG("PM2XXX_INP_MODE_VPWR", PM2XXX_INP_MODE_VPWR, DDBG_RW),
+ DDBG_REG("PM2XXX_BATT_WD_KICK", PM2XXX_BATT_WD_KICK, DDBG_RW),
+ DDBG_REG("PM2XXX_DEV_VER_STAT", PM2XXX_DEV_VER_STAT, DDBG_RO),
+ DDBG_REG("PM2XXX_THERM_WARN_CTRL", PM2XXX_THERM_WARN_CTRL_REG, DDBG_RW),
+ DDBG_REG("PM2XXX_BAT_DISC_REG", PM2XXX_BATT_DISC_REG, DDBG_RW),
+ DDBG_REG("PM2XXX_BAT_LWLEV_CMP", PM2XXX_BATT_LOW_LEV_COMP_REG, DDBG_RW),
+ DDBG_REG("PM2XXX_BAT_LWLEV_VAL", PM2XXX_BATT_LOW_LEV_VAL_REG, DDBG_RW),
+ DDBG_REG("PM2XXX_I2C_PAD_CTRL_REG", PM2XXX_I2C_PAD_CTRL_REG, DDBG_RW),
+ DDBG_REG("PM2XXX_SW_CTRL_REG", PM2XXX_SW_CTRL_REG, DDBG_RW),
+ DDBG_REG("PM2XXX_LED_CTRL_REG", PM2XXX_LED_CTRL_REG, DDBG_RO),
+ DDBG_REG("PM2XXX_REG_INT1", PM2XXX_REG_INT1, DDBG_RO),
+ DDBG_REG("PM2XXX_MASK_REG_INT1", PM2XXX_MASK_REG_INT1, DDBG_RW),
+ DDBG_REG("PM2XXX_SRCE_REG_INT1", PM2XXX_SRCE_REG_INT1, DDBG_RO),
+ DDBG_REG("PM2XXX_REG_INT2", PM2XXX_REG_INT2, DDBG_RO),
+ DDBG_REG("PM2XXX_MASK_REG_INT2", PM2XXX_MASK_REG_INT2, DDBG_RW),
+ DDBG_REG("PM2XXX_SRCE_REG_INT2", PM2XXX_SRCE_REG_INT2, DDBG_RO),
+ DDBG_REG("PM2XXX_REG_INT3", PM2XXX_REG_INT3, DDBG_RO),
+ DDBG_REG("PM2XXX_MASK_REG_INT3", PM2XXX_MASK_REG_INT3, DDBG_RW),
+ DDBG_REG("PM2XXX_SRCE_REG_INT3", PM2XXX_SRCE_REG_INT3, DDBG_RO),
+ DDBG_REG("PM2XXX_REG_INT4", PM2XXX_REG_INT4, DDBG_RO),
+ DDBG_REG("PM2XXX_MASK_REG_INT4", PM2XXX_MASK_REG_INT4, DDBG_RW),
+ DDBG_REG("PM2XXX_SRCE_REG_INT4", PM2XXX_SRCE_REG_INT4, DDBG_RO),
+ DDBG_REG("PM2XXX_REG_INT5", PM2XXX_REG_INT5, DDBG_RO),
+ DDBG_REG("PM2XXX_MASK_REG_INT5", PM2XXX_MASK_REG_INT5, DDBG_RW),
+ DDBG_REG("PM2XXX_SRCE_REG_INT5", PM2XXX_SRCE_REG_INT5, DDBG_RO),
+ DDBG_REG("PM2XXX_REG_INT6", PM2XXX_REG_INT6, DDBG_RO),
+ DDBG_REG("PM2XXX_MASK_REG_INT6", PM2XXX_MASK_REG_INT6, DDBG_RW),
+ DDBG_REG("PM2XXX_SRCE_REG_INT6", PM2XXX_SRCE_REG_INT6, DDBG_RO),
+ DDBG_REG_NULL,
+};
+
+static struct pm2xxx_charger *pm2xxx_ddbg;
+#endif
+
+struct pm2xxx_irq {
+ char *name;
+ irqreturn_t (*isr)(int irq, void *data);
+};
+
+struct pm2xxx_charger_info {
+ int charger_connected;
+ int charger_online;
+ int charger_voltage;
+ int cv_active;
+ bool wd_expired;
+};
+
+struct pm2xxx_charger_event_flags {
+ bool mainextchnotok;
+ bool main_thermal_prot;
+ bool ovv;
+ bool chgwdexp;
+};
+
+struct pm2xxx_config {
+ struct i2c_client *pm2xxx_i2c;
+ struct i2c_device_id *pm2xxx_id;
+};
+
+struct pm2xxx_charger {
+ struct device *dev;
+ u8 chip_id;
+ bool vddadc_en_ac;
+ struct pm2xxx_config config;
+ bool ac_conn;
+ unsigned int gpio_irq;
+ int vbat;
+ int old_vbat;
+ int failure_case;
+ int failure_input_ovv;
+ int pm2_int[6];
+ struct ab8500_gpadc *gpadc;
+ struct regulator *regu;
+ struct pm2xxx_bm_data *bat;
+ struct mutex lock;
+ struct ab8500 *parent;
+ struct pm2xxx_charger_info ac;
+ struct pm2xxx_charger_platform_data *pdata;
+ struct workqueue_struct *charger_wq;
+ struct delayed_work check_vbat_work;
+ struct work_struct ac_work;
+ struct work_struct check_main_thermal_prot_work;
+ struct ux500_charger ac_chg;
+ struct pm2xxx_charger_event_flags flags;
+#ifdef CONFIG_PM2XXX_DEEP_DEBUG
+ struct dentry *ddbg_dir_pm2xxx;
+#endif
+};
+
+static const struct i2c_device_id pm2xxx_ident[] = {
+ { "pm2301", 0 },
+ { }
+};
+
+static int __pm2xxx_read(struct pm2xxx_charger *pm2, int reg, int num, u8 *data)
+{
+ int ret;
+
+ ret = i2c_smbus_read_i2c_block_data(pm2->config.pm2xxx_i2c, reg,
+ num, (u8 *)data);
+ if (ret < 0)
+ dev_err(pm2->dev, "Error reading %d regs at %d\n", num, reg);
+
+ return ret;
+}
+
+static int __pm2xxx_write(struct pm2xxx_charger *pm2, int reg, int num, u8 data)
+{
+ int ret;
+
+ ret = i2c_smbus_write_i2c_block_data(pm2->config.pm2xxx_i2c, reg,
+ num, &data);
+ if (ret < 0)
+ dev_err(pm2->dev, "Error writing %d regs at %d\n", num, reg);
+
+ return ret;
+
+}
+
+static int pm2xxx_reg_read(struct pm2xxx_charger *pm2, int reg)
+{
+ u8 val;
+
+ __pm2xxx_read(pm2, reg, 1, &val);
+
+ return val;
+}
+
+static int pm2xxx_reg_write(struct pm2xxx_charger *pm2, int reg, u8 val)
+{
+ int ret;
+
+ ret = __pm2xxx_write(pm2, reg, 1, val);
+
+ return ret;
+}
+
+int pm2xxx_charging_enable_mngt(struct pm2xxx_charger *pm2)
+{
+ int ret;
+
+ /* Enable charging */
+ ret = pm2xxx_reg_write(pm2, PM2XXX_BATT_CTRL_REG2,
+ (PM2XXX_CH_AUTO_RESUME_EN | PM2XXX_CHARGER_ENA));
+
+ return ret;
+}
+
+int pm2xxx_charging_disable_mngt(struct pm2xxx_charger *pm2)
+{
+ int ret;
+
+ /* Disable charging */
+ ret = pm2xxx_reg_write(pm2, PM2XXX_BATT_CTRL_REG2,
+ (PM2XXX_CH_AUTO_RESUME_DIS | PM2XXX_CHARGER_DIS));
+
+ return ret;
+}
+
+int pm2xxx_charger_batt_therm_mngt(struct pm2xxx_charger *pm2, int val)
+{
+ queue_work(pm2->charger_wq, &pm2->check_main_thermal_prot_work);
+
+ return 0;
+}
+
+
+int pm2xxx_charger_die_therm_mngt(struct pm2xxx_charger *pm2, int val)
+{
+ queue_work(pm2->charger_wq, &pm2->check_main_thermal_prot_work);
+
+ return 0;
+}
+
+int pm2xxx_charger_ovv_mngt(struct pm2xxx_charger *pm2, int val)
+{
+ int ret = 0;
+
+ pm2->failure_input_ovv++;
+ if (pm2->failure_input_ovv < 4) {
+ ret = pm2xxx_charging_enable_mngt(pm2);
+ goto out;
+ } else {
+ pm2->failure_input_ovv = 0;
+ dev_err(pm2->dev, "Overvoltage detected\n");
+ pm2->flags.ovv = true;
+ power_supply_changed(&pm2->ac_chg.psy);
+ }
+
+out:
+ return ret;
+}
+
+int pm2xxx_charger_wd_exp_mngt(struct pm2xxx_charger *pm2, int val)
+{
+ dev_dbg(pm2->dev , "20 minutes watchdog occured\n");
+
+ pm2->ac.wd_expired = true;
+ power_supply_changed(&pm2->ac_chg.psy);
+
+ return 0;
+}
+
+int pm2xxx_charger_vbat_lsig_mngt(struct pm2xxx_charger *pm2, int val)
+{
+ switch (val) {
+ case PM2XXX_INT1_ITVBATLOWR:
+ dev_dbg(pm2->dev, "VBAT grows above VBAT_LOW level\n");
+ /* TODO: Handle this */
+ break;
+
+ case PM2XXX_INT1_ITVBATLOWF:
+ dev_dbg(pm2->dev, "VBAT drops below VBAT_LOW level\n");
+ /* TODO: Handle this */
+ break;
+
+ default:
+ dev_err(pm2->dev, "Unknown VBAT level\n");
+ }
+
+ return 0;
+}
+
+int pm2xxx_charger_bat_disc_mngt(struct pm2xxx_charger *pm2, int val)
+{
+ int ret;
+
+ dev_dbg(pm2->dev, "battery disconnected\n");
+
+ /* TODO: Update charging status */
+ ret = pm2xxx_charging_disable_mngt(pm2);
+
+ return ret;
+}
+
+static int pm2xxx_charger_detection(struct pm2xxx_charger *pm2)
+{
+ int ret = 0;
+
+ ret = pm2xxx_reg_read(pm2, PM2XXX_SRCE_REG_INT2);
+
+ if (ret < 0) {
+ dev_err(pm2->dev, "Charger detection failed\n");
+ return ret;
+ }
+
+ ret &= (PM2XXX_INT2_S_ITVPWR1PLUG | PM2XXX_INT2_S_ITVPWR2PLUG);
+
+ return ret;
+}
+
+static int pm2xxx_charger_itv_pwr_plug_mngt(struct pm2xxx_charger *pm2, int val)
+{
+
+ int ret;
+
+ /*
+ * Since we can't be sure that the events are received
+ * synchronously, we have the check if the main charger is
+ * connected by reading the interrupt source register.
+ */
+ ret = pm2xxx_charger_detection(pm2);
+
+ if (ret > 0) {
+ pm2->ac.charger_connected = 1;
+ pm2->ac_conn = true;
+
+ queue_work(pm2->charger_wq, &pm2->ac_work);
+ }
+
+
+ return ret;
+}
+
+static int pm2xxx_charger_itv_pwr_unplug_mngt(struct pm2xxx_charger *pm2,
+ int val)
+{
+ pm2->ac.charger_connected = 0;
+ queue_work(pm2->charger_wq, &pm2->ac_work);
+
+ return 0;
+}
+
+static int pm2_int_reg0(struct pm2xxx_charger *pm2)
+{
+ int ret;
+
+ if (pm2->pm2_int[0] &
+ (PM2XXX_INT1_ITVBATLOWR | PM2XXX_INT1_ITVBATLOWF)) {
+ ret = pm2xxx_charger_vbat_lsig_mngt(pm2, pm2->pm2_int[0] &
+ (PM2XXX_INT1_ITVBATLOWR | PM2XXX_INT1_ITVBATLOWF));
+ }
+
+ if (pm2->pm2_int[0] & PM2XXX_INT1_ITVBATDISCONNECT) {
+ ret = pm2xxx_charger_bat_disc_mngt(pm2,
+ PM2XXX_INT1_ITVBATDISCONNECT);
+ }
+
+ return ret;
+}
+
+static int pm2_int_reg1(struct pm2xxx_charger *pm2)
+{
+ int ret;
+
+ if (pm2->pm2_int[1] &
+ (PM2XXX_INT2_ITVPWR1PLUG | PM2XXX_INT2_ITVPWR2PLUG)) {
+ dev_dbg(pm2->dev , "Main charger plugged\n");
+ ret = pm2xxx_charger_itv_pwr_plug_mngt(pm2, pm2->pm2_int[1] &
+ (PM2XXX_INT2_ITVPWR1PLUG | PM2XXX_INT2_ITVPWR2PLUG));
+ }
+
+ if (pm2->pm2_int[1] &
+ (PM2XXX_INT2_ITVPWR1UNPLUG | PM2XXX_INT2_ITVPWR2UNPLUG)) {
+ dev_dbg(pm2->dev , "Main charger unplugged\n");
+ ret = pm2xxx_charger_itv_pwr_unplug_mngt(pm2, pm2->pm2_int[1] &
+ (PM2XXX_INT2_ITVPWR1UNPLUG |
+ PM2XXX_INT2_ITVPWR2UNPLUG));
+ }
+
+
+ return ret;
+}
+
+static int pm2_int_reg2(struct pm2xxx_charger *pm2)
+{
+ int ret;
+
+ if (pm2->pm2_int[2] & PM2XXX_INT3_ITAUTOTIMEOUTWD)
+ ret = pm2xxx_charger_wd_exp_mngt(pm2, pm2->pm2_int[2]);
+
+ if (pm2->pm2_int[2] & (PM2XXX_INT3_ITCHPRECHARGEWD |
+ PM2XXX_INT3_ITCHCCWD | PM2XXX_INT3_ITCHCVWD)) {
+ dev_dbg(pm2->dev,
+ "Watchdog occured for precharge, CC and CV charge\n");
+
+ /*TODO: handle watchdog expired */
+ }
+
+ return ret;
+}
+
+static int pm2_int_reg3(struct pm2xxx_charger *pm2)
+{
+ int ret;
+
+ if (pm2->pm2_int[3] & (PM2XXX_INT4_ITCHARGINGON)) {
+ dev_dbg(pm2->dev ,
+ "chargind operation has started\n");
+
+ /* TODO: Handle charging started */
+ }
+
+ if (pm2->pm2_int[3] & (PM2XXX_INT4_ITVRESUME)) {
+
+ dev_dbg(pm2->dev,
+ "battery discharged down to VResume threshold\n");
+
+ /* TODO: Handle recharging */
+ }
+
+ if (pm2->pm2_int[3] & (PM2XXX_INT4_ITBATTFULL)) {
+
+ dev_dbg(pm2->dev , "battery fully detected\n");
+
+ /* TODO: Handle battery full */
+ }
+
+ if (pm2->pm2_int[3] & (PM2XXX_INT4_ITCVPHASE)) {
+
+ dev_dbg(pm2->dev, "CV phase enter with 0.5C charging\n");
+
+ /* TODO: Handle CC to CV transition */
+ }
+
+ if (pm2->pm2_int[3] &
+ (PM2XXX_INT4_ITVPWR2OVV | PM2XXX_INT4_ITVPWR1OVV)) {
+ pm2->failure_case = VPWR_OVV;
+ ret = pm2xxx_charger_ovv_mngt(pm2, pm2->pm2_int[3] &
+ (PM2XXX_INT4_ITVPWR2OVV | PM2XXX_INT4_ITVPWR1OVV));
+ dev_dbg(pm2->dev, "VPWR/VSYSTEM overvoltage detected\n");
+ }
+
+ if (pm2->pm2_int[3] & (PM2XXX_INT4_S_ITBATTEMPCOLD |
+ PM2XXX_INT4_S_ITBATTEMPHOT)) {
+
+ pm2xxx_charger_batt_therm_mngt(pm2,
+ pm2->pm2_int[3] & (PM2XXX_INT4_S_ITBATTEMPCOLD |
+ PM2XXX_INT4_S_ITBATTEMPHOT));
+ dev_dbg(pm2->dev, "BTEMP is too Low/High\n");
+ }
+
+ return ret;
+}
+
+static int pm2_int_reg4(struct pm2xxx_charger *pm2)
+{
+ int ret;
+
+ if (pm2->pm2_int[4] & PM2XXX_INT5_ITVSYSTEMOVV) {
+ pm2->failure_case = VSYSTEM_OVV;
+ ret = pm2xxx_charger_ovv_mngt(pm2, pm2->pm2_int[4] &
+ PM2XXX_INT5_ITVSYSTEMOVV);
+ dev_dbg(pm2->dev, "VSYSTEM overvoltage detected\n");
+ }
+
+ if (pm2->pm2_int[4] & (PM2XXX_INT5_ITTHERMALWARNINGFALL |
+ PM2XXX_INT5_ITTHERMALWARNINGRISE |
+ PM2XXX_INT5_ITTHERMALSHUTDOWNFALL |
+ PM2XXX_INT5_ITTHERMALSHUTDOWNRISE)) {
+ dev_dbg(pm2->dev, "BTEMP die temperature is too Low/High\n");
+ ret = pm2xxx_charger_die_therm_mngt(pm2, pm2->pm2_int[4] &
+ (PM2XXX_INT5_ITTHERMALWARNINGFALL |
+ PM2XXX_INT5_ITTHERMALWARNINGRISE |
+ PM2XXX_INT5_ITTHERMALSHUTDOWNFALL |
+ PM2XXX_INT5_ITTHERMALSHUTDOWNRISE));
+ }
+
+ return ret;
+}
+
+static int pm2_int_reg5(struct pm2xxx_charger *pm2)
+{
+
+ if (pm2->pm2_int[5]
+ & (PM2XXX_INT6_ITVPWR2DROP | PM2XXX_INT6_ITVPWR1DROP)) {
+ dev_dbg(pm2->dev, "VMPWR drop to VBAT level\n");
+
+ /* TODO: handle this */
+ }
+
+ if (pm2->pm2_int[5] & (PM2XXX_INT6_ITVPWR2VALIDRISE |
+ PM2XXX_INT6_ITVPWR1VALIDRISE |
+ PM2XXX_INT6_ITVPWR2VALIDFALL |
+ PM2XXX_INT6_ITVPWR1VALIDFALL)) {
+ dev_dbg(pm2->dev, "Falling/Rising edge on WPWR1/2\n");
+
+ /* TODO: handle this */
+ }
+
+ return 0;
+}
+
+static irqreturn_t pm2xxx_irq_int(int irq, void *data)
+{
+ struct pm2xxx_charger *pm2 = data;
+ int ret, i;
+
+ for (i = 0; i < ARRAY_SIZE(pm2->pm2_int); i++) {
+ ret = pm2xxx_reg_read(pm2, pm2xxx_interrupt_registers[i]);
+ pm2->pm2_int[i] = ret;
+ }
+
+ pm2_int_reg0(pm2);
+ pm2_int_reg1(pm2);
+ pm2_int_reg2(pm2);
+ pm2_int_reg3(pm2);
+ pm2_int_reg4(pm2);
+ pm2_int_reg5(pm2);
+
+ return IRQ_HANDLED;
+}
+
+int pm2xxx_charger_led_en(struct pm2xxx_charger *pm2, int on)
+{
+ return 0;
+}
+
+static int pm2xxx_charger_get_ac_voltage(struct pm2xxx_charger *pm2)
+{
+ int vch = 0;
+
+ if (pm2->ac.charger_connected) {
+ vch = ab8500_gpadc_convert(pm2->gpadc, MAIN_CHARGER_V);
+ if (vch < 0)
+ dev_err(pm2->dev, "%s gpadc conv failed,\n", __func__);
+ }
+
+ return vch;
+}
+
+static int pm2xxx_charger_ac_cv(struct pm2xxx_charger *pm2)
+{
+ int ret = 0;
+
+ if (pm2->ac.charger_connected && pm2->ac.charger_online) {
+
+ ret = pm2xxx_reg_read(pm2, PM2XXX_SRCE_REG_INT4);
+ if (ret < 0) {
+ dev_err(pm2->dev, "%s pm2xxx read failed\n", __func__);
+ return 0;
+ }
+
+ if (ret & PM2XXX_INT4_S_ITCVPHASE)
+ ret = 1;
+ else
+ ret = 0;
+ }
+
+ return ret;
+}
+
+static int pm2xxx_charger_get_ac_current(struct pm2xxx_charger *pm2)
+{
+ int ich = 0;
+
+ if (pm2->ac.charger_online) {
+ ich = ab8500_gpadc_convert(pm2->gpadc, MAIN_CHARGER_C);
+ if (ich < 0)
+ dev_err(pm2->dev, "%s gpadc conv failed\n", __func__);
+ }
+
+ return ich;
+}
+
+static int pm2xxx_current_to_regval(int curr)
+{
+ int i;
+
+ if (curr < pm2xxx_charger_current_map[0])
+ return 0;
+
+ for (i = 0; i < ARRAY_SIZE(pm2xxx_charger_current_map); i++) {
+ if (curr < pm2xxx_charger_current_map[i])
+ return i - 1;
+ }
+
+ i = ARRAY_SIZE(pm2xxx_charger_current_map) - 1;
+ if (curr == pm2xxx_charger_current_map[i])
+ return i;
+ else
+ return -1;
+}
+
+static int pm2xxx_voltage_to_regval(int curr)
+{
+ int i;
+
+ if (curr < pm2xxx_charger_voltage_map[0])
+ return 0;
+
+ for (i = 0; i < ARRAY_SIZE(pm2xxx_charger_voltage_map); i++) {
+ if (curr < pm2xxx_charger_voltage_map[i])
+ return i - 1;
+ }
+
+ i = ARRAY_SIZE(pm2xxx_charger_voltage_map) - 1;
+ if (curr == pm2xxx_charger_voltage_map[i])
+ return i;
+ else
+ return -1;
+}
+
+static int pm2xxx_charger_update_charger_current(struct ux500_charger *charger,
+ int ich_out)
+{
+ int ret;
+ int curr_index;
+ struct pm2xxx_charger *pm2;
+
+ if (charger->psy.type == POWER_SUPPLY_TYPE_MAINS)
+ pm2 = to_pm2xxx_charger_ac_device_info(charger);
+ else
+ return -ENXIO;
+
+ curr_index = pm2xxx_current_to_regval(ich_out);
+ if (curr_index < 0) {
+ dev_err(pm2->dev,
+ "Charger current too high, "
+ "charging not started\n");
+ return -ENXIO;
+ }
+
+ ret = pm2xxx_reg_read(pm2, PM2XXX_BATT_CTRL_REG6);
+ if (ret >= 0) {
+ ret &= ~0xf;
+ ret |= curr_index;
+ ret = pm2xxx_reg_write(pm2, PM2XXX_BATT_CTRL_REG6, ret);
+ if (ret < 0) {
+ dev_err(pm2->dev,
+ "%s write failed\n", __func__);
+ }
+ }
+
+ return ret;
+}
+
+static int pm2xxx_charger_ac_get_property(struct power_supply *psy,
+ enum power_supply_property psp,
+ union power_supply_propval *val)
+{
+ struct pm2xxx_charger *pm2;
+
+ pm2 = to_pm2xxx_charger_ac_device_info(psy_to_ux500_charger(psy));
+
+ switch (psp) {
+ case POWER_SUPPLY_PROP_HEALTH:
+ if (pm2->flags.mainextchnotok)
+ val->intval = POWER_SUPPLY_HEALTH_UNSPEC_FAILURE;
+ else if (pm2->ac.wd_expired)
+ val->intval = POWER_SUPPLY_HEALTH_DEAD;
+ else if (pm2->flags.main_thermal_prot)
+ val->intval = POWER_SUPPLY_HEALTH_OVERHEAT;
+ else
+ val->intval = POWER_SUPPLY_HEALTH_GOOD;
+ break;
+ case POWER_SUPPLY_PROP_ONLINE:
+ val->intval = pm2->ac.charger_online;
+ break;
+ case POWER_SUPPLY_PROP_PRESENT:
+ val->intval = pm2->ac.charger_connected;
+ break;
+ case POWER_SUPPLY_PROP_VOLTAGE_NOW:
+ pm2->ac.charger_voltage = pm2xxx_charger_get_ac_voltage(pm2);
+ val->intval = pm2->ac.charger_voltage * 1000;
+ break;
+ case POWER_SUPPLY_PROP_VOLTAGE_AVG:
+ pm2->ac.cv_active = pm2xxx_charger_ac_cv(pm2);
+ val->intval = pm2->ac.cv_active;
+ break;
+ case POWER_SUPPLY_PROP_CURRENT_NOW:
+ val->intval = pm2xxx_charger_get_ac_current(pm2) * 1000;
+ break;
+ default:
+ return -EINVAL;
+ }
+ return 0;
+}
+
+static int pm2xxx_charging_init(struct pm2xxx_charger *pm2)
+{
+ int ret;
+
+ /* enable CC and CV watchdog */
+ ret = pm2xxx_reg_write(pm2, PM2XXX_BATT_CTRL_REG3,
+ (PM2XXX_CH_WD_CV_PHASE_60MIN | PM2XXX_CH_WD_CC_PHASE_60MIN));
+
+ /* enable precharge watchdog */
+ ret = pm2xxx_reg_write(pm2, PM2XXX_BATT_CTRL_REG4,
+ PM2XXX_CH_WD_PRECH_PHASE_60MIN);
+
+ return ret;
+}
+
+static int pm2xxx_charger_ac_en(struct ux500_charger *charger,
+ int enable, int vset, int iset)
+{
+ int ret;
+ int volt_index;
+ int curr_index;
+
+ struct pm2xxx_charger *pm2 = to_pm2xxx_charger_ac_device_info(charger);
+
+ if (enable) {
+ if (!pm2->ac.charger_connected) {
+ dev_dbg(pm2->dev, "AC charger not connected\n");
+ return -ENXIO;
+ }
+
+ dev_dbg(pm2->dev, "Enable AC: %dmV %dmA\n", vset, iset);
+ if (!pm2->vddadc_en_ac) {
+ regulator_enable(pm2->regu);
+ pm2->vddadc_en_ac = true;
+ }
+
+ pm2xxx_charging_init(pm2);
+
+ volt_index = pm2xxx_voltage_to_regval(vset);
+ curr_index = pm2xxx_current_to_regval(iset);
+
+ if (volt_index < 0 || curr_index < 0) {
+ dev_err(pm2->dev,
+ "Charger voltage or current too high, "
+ "charging not started\n");
+ return -ENXIO;
+ }
+
+ ret = pm2xxx_reg_read(pm2, PM2XXX_BATT_CTRL_REG8);
+ if (ret >= 0) {
+ ret &= ~0x3F;
+ ret |= volt_index;
+ ret = pm2xxx_reg_write(pm2, PM2XXX_BATT_CTRL_REG8, ret);
+
+ if (ret < 0) {
+ dev_err(pm2->dev,
+ "%s write failed\n", __func__);
+ goto error_occured;
+ }
+ }
+
+ ret = pm2xxx_reg_read(pm2, PM2XXX_BATT_CTRL_REG6);
+ if (ret >= 0) {
+ ret &= ~0xf;
+ ret |= curr_index;
+ ret = pm2xxx_reg_write(pm2, PM2XXX_BATT_CTRL_REG6, ret);
+ if (ret < 0) {
+ dev_err(pm2->dev,
+ "%s write failed\n", __func__);
+ goto error_occured;
+ }
+ }
+
+ if (!pm2->bat->enable_overshoot) {
+ ret = pm2xxx_reg_read(pm2, PM2XXX_LED_CTRL_REG);
+ if (ret >= 0) {
+ ret |= 0x01;
+ ret = pm2xxx_reg_write(pm2, PM2XXX_LED_CTRL_REG,
+ ret);
+ if (ret < 0)
+ goto error_occured;
+ }
+ }
+
+ ret = pm2xxx_charging_enable_mngt(pm2);
+ if (ret) {
+ dev_err(pm2->dev, "%s write failed\n", __func__);
+ return ret;
+ }
+
+ /*TODO: Add pm2301 Enable LED code */
+
+ pm2->ac.charger_online = 1;
+ } else {
+ /* TODO: add correct LED disable code */
+
+ pm2->ac.charger_online = 0;
+ pm2->ac.wd_expired = false;
+
+ /* Disable regulator if enabled */
+ if (pm2->vddadc_en_ac) {
+ regulator_disable(pm2->regu);
+ pm2->vddadc_en_ac = false;
+ }
+
+ ret = pm2xxx_charging_disable_mngt(pm2);
+ if (ret) {
+ dev_err(pm2->dev, "%s write failed\n", __func__);
+ return ret;
+ }
+
+ dev_dbg(pm2->dev, "PM2301: " "Disabled AC charging\n");
+ }
+ power_supply_changed(&pm2->ac_chg.psy);
+
+error_occured:
+ return ret;
+}
+
+static int pm2xxx_charger_watchdog_kick(struct ux500_charger *charger)
+{
+ int ret;
+ struct pm2xxx_charger *pm2;
+
+ if (charger->psy.type == POWER_SUPPLY_TYPE_MAINS)
+ pm2 = to_pm2xxx_charger_ac_device_info(charger);
+ else
+ return -ENXIO;
+
+ ret = pm2xxx_reg_write(pm2, PM2XXX_BATT_WD_KICK, WD_TIMER);
+ if (ret)
+ dev_err(pm2->dev, "Failed to kick WD!\n");
+
+ return ret;
+}
+
+static void pm2xxx_charger_ac_work(struct work_struct *work)
+{
+ struct pm2xxx_charger *pm2 = container_of(work,
+ struct pm2xxx_charger, ac_work);
+
+
+ power_supply_changed(&pm2->ac_chg.psy);
+ sysfs_notify(&pm2->ac_chg.psy.dev->kobj, NULL, "present");
+};
+
+/* TODO: how thermal protection is handled in pm2301 */
+static void pm2xxx_charger_check_main_thermal_prot_work(
+ struct work_struct *work)
+{
+
+ /* TODO: check the thermal and die thermal protection */
+};
+
+static struct pm2xxx_irq pm2xxx_charger_irq[] = {
+ {"PM2XXX_IRQ_INT", pm2xxx_irq_int},
+};
+
+static int pm2xxx_wall_charger_resume(struct i2c_client *i2c_client)
+{
+ return 0;
+}
+
+static int pm2xxx_wall_charger_suspend(struct i2c_client *i2c_client,
+ pm_message_t state)
+{
+ return 0;
+}
+
+#ifdef CONFIG_PM2XXX_DEEP_DEBUG
+static int pm2xxx_ddbg_write(u32 addr, u32 val)
+{
+ int err;
+
+ err = pm2xxx_reg_write(pm2xxx_ddbg, addr, val);
+
+ if (err < 0)
+ return -EIO;
+
+ return 0;
+}
+
+static int pm2xxx_ddbg_read(u32 addr, u32 *val)
+{
+ *val = pm2xxx_reg_read(pm2xxx_ddbg, addr);
+
+ if (val < 0)
+ return -EIO;
+
+ return 0;
+}
+
+static struct ddbg_target ddbg_pm2xxx = {
+ .phyaddr = 0,
+ .reg = ddbg_pm2xxx_registers,
+ .read_reg = pm2xxx_ddbg_read,
+ .write_reg = pm2xxx_ddbg_write,
+};
+#endif
+
+static int __devinit pm2xxx_wall_charger_probe(struct i2c_client *i2c_client,
+ const struct i2c_device_id *id)
+{
+ struct pm2xxx_platform_data *pl_data = i2c_client->dev.platform_data;
+ struct pm2xxx_charger *pm2;
+ int ret = 0;
+
+ pm2 = kzalloc(sizeof(struct pm2xxx_charger), GFP_KERNEL);
+ if (!pm2)
+ return -ENOMEM;
+
+ /* get parent data */
+ pm2->dev = &i2c_client->dev;
+ pm2->gpadc = ab8500_gpadc_get();
+
+ /* get charger spcific platform data */
+ if (!pl_data->wall_charger) {
+ dev_err(pm2->dev, "no charger platform data supplied\n");
+ ret = -EINVAL;
+ goto free_device_info;
+ }
+
+ pm2->pdata = pl_data->wall_charger;
+
+ /* get battery specific platform data */
+ if (!pl_data->battery) {
+ dev_err(pm2->dev, "no battery platform data supplied\n");
+ ret = -EINVAL;
+ goto free_device_info;
+ }
+
+ pm2->bat = pl_data->battery;
+
+ if (!i2c_check_functionality(i2c_client->adapter,
+ I2C_FUNC_SMBUS_BYTE_DATA |
+ I2C_FUNC_SMBUS_READ_WORD_DATA)) {
+ ret = -ENODEV;
+ dev_info(pm2->dev, "pm2301 i2c_check_functionality failed\n");
+ goto free_device_info;
+ }
+
+ pm2->config.pm2xxx_i2c = i2c_client;
+ pm2->config.pm2xxx_id = (struct i2c_device_id *) id;
+ i2c_set_clientdata(i2c_client, pm2);
+
+ /* AC supply */
+ /* power_supply base class */
+ pm2->ac_chg.psy.name = pm2->pdata->label;
+ pm2->ac_chg.psy.type = POWER_SUPPLY_TYPE_MAINS;
+ pm2->ac_chg.psy.properties = pm2xxx_charger_ac_props;
+ pm2->ac_chg.psy.num_properties = ARRAY_SIZE(pm2xxx_charger_ac_props);
+ pm2->ac_chg.psy.get_property = pm2xxx_charger_ac_get_property;
+ pm2->ac_chg.psy.supplied_to = pm2->pdata->supplied_to;
+ pm2->ac_chg.psy.num_supplicants = pm2->pdata->num_supplicants;
+ /* pm2xxx_charger sub-class */
+ pm2->ac_chg.ops.enable = &pm2xxx_charger_ac_en;
+ pm2->ac_chg.ops.kick_wd = &pm2xxx_charger_watchdog_kick;
+ pm2->ac_chg.ops.update_curr = &pm2xxx_charger_update_charger_current;
+ pm2->ac_chg.max_out_volt = pm2xxx_charger_voltage_map[
+ ARRAY_SIZE(pm2xxx_charger_voltage_map) - 1];
+ pm2->ac_chg.max_out_curr = pm2xxx_charger_current_map[
+ ARRAY_SIZE(pm2xxx_charger_current_map) - 1];
+
+ /* Create a work queue for the charger */
+ pm2->charger_wq =
+ create_singlethread_workqueue("pm2xxx_charger_wq");
+ if (pm2->charger_wq == NULL) {
+ dev_err(pm2->dev, "failed to create work queue\n");
+ goto free_device_info;
+ }
+
+ /* Init work for charger detection */
+ INIT_WORK(&pm2->ac_work, pm2xxx_charger_ac_work);
+
+ /* Init work for checking HW status */
+ INIT_WORK(&pm2->check_main_thermal_prot_work,
+ pm2xxx_charger_check_main_thermal_prot_work);
+
+ /*
+ * VDD ADC supply needs to be enabled from this driver when there
+ * is a charger connected to avoid erroneous BTEMP_HIGH/LOW
+ * interrupts during charging
+ */
+ pm2->regu = regulator_get(pm2->dev, "vddadc");
+ if (IS_ERR(pm2->regu)) {
+ ret = PTR_ERR(pm2->regu);
+ dev_err(pm2->dev, "failed to get vddadc regulator\n");
+ goto free_charger_wq;
+ }
+
+ /* Register AC charger class */
+ ret = power_supply_register(pm2->dev, &pm2->ac_chg.psy);
+ if (ret) {
+ dev_err(pm2->dev, "failed to register AC charger\n");
+ goto free_regulator;
+ }
+
+ /* Register interrupts */
+ ret = request_threaded_irq(pm2->pdata->irq_number, NULL,
+ pm2xxx_charger_irq[0].isr,
+ pm2->pdata->irq_type,
+ pm2xxx_charger_irq[0].name, pm2);
+
+ if (ret != 0) {
+ dev_err(pm2->dev, "failed to request %s IRQ %d: %d\n"
+ , pm2xxx_charger_irq[0].name, pm2->pdata->irq_number, ret);
+ goto unregister_pm2xxx_charger;
+ }
+
+ /* TODO: I2C Read/Write will fail, if AC adaptor is not connected.
+ * fix the charger detection mechanism.
+ */
+ ret = pm2xxx_charger_detection(pm2);
+
+ if (ret > 0) {
+ pm2->ac.charger_connected = 1;
+ pm2->ac_conn = true;
+ power_supply_changed(&pm2->ac_chg.psy);
+ sysfs_notify(&pm2->ac_chg.psy.dev->kobj, NULL, "present");
+ }
+
+#ifdef CONFIG_PM2XXX_DEEP_DEBUG
+ pm2xxx_ddbg = pm2;
+ pm2->ddbg_dir_pm2xxx = debugfs_create_dir("pm2xxx", NULL);
+ if (pm2->ddbg_dir_pm2xxx == NULL) {
+ ret = -ENOMEM;
+ goto err_deep_debug;
+ }
+ ret = deep_debug_register(&ddbg_pm2xxx, pm2->ddbg_dir_pm2xxx);
+ if (ret)
+ goto err_deep_debug;
+#endif
+
+ return 0;
+
+#ifdef CONFIG_PM2XXX_DEEP_DEBUG
+err_deep_debug:
+ if (pm2->ddbg_dir_pm2xxx) {
+ debugfs_remove_recursive(pm2->ddbg_dir_pm2xxx);
+ pm2->ddbg_dir_pm2xxx = NULL;
+ }
+ dev_err(pm2->dev, "failed to create debugfs entries.\n");
+
+ /* disable interrupt */
+ free_irq(pm2->pdata->irq_number, pm2);
+#endif
+
+unregister_pm2xxx_charger:
+ /* unregister power supply */
+ power_supply_unregister(&pm2->ac_chg.psy);
+free_regulator:
+ /* disable the regulator */
+ regulator_put(pm2->regu);
+free_charger_wq:
+ destroy_workqueue(pm2->charger_wq);
+free_device_info:
+ kfree(pm2);
+ return ret;
+}
+
+static int __devexit pm2xxx_wall_charger_remove(struct i2c_client *i2c_client)
+{
+ struct pm2xxx_charger *pm2 = i2c_get_clientdata(i2c_client);
+
+ /* Disable AC charging */
+ pm2xxx_charger_ac_en(&pm2->ac_chg, false, 0, 0);
+
+ /* Disable interrupts */
+ free_irq(pm2->pdata->irq_number, pm2);
+
+ /* Delete the work queue */
+ destroy_workqueue(pm2->charger_wq);
+
+#ifdef CONFIG_PM2XXX_DEEP_DEBUG
+ deep_debug_unregister(&ddbg_pm2xxx);
+ if (pm2->ddbg_dir_pm2xxx)
+ debugfs_remove_recursive(pm2->ddbg_dir_pm2xxx);
+#endif
+
+ flush_scheduled_work();
+
+ /* disable the regulator */
+ regulator_put(pm2->regu);
+
+ power_supply_unregister(&pm2->ac_chg.psy);
+
+ kfree(pm2);
+
+ return 0;
+}
+
+static const struct i2c_device_id pm2xxx_id[] = {
+ { "pm2301", 0 },
+ { }
+};
+
+MODULE_DEVICE_TABLE(i2c, pm2xxx_id);
+
+static struct i2c_driver pm2xxx_charger_driver = {
+ .probe = pm2xxx_wall_charger_probe,
+ .remove = __devexit_p(pm2xxx_wall_charger_remove),
+ .suspend = pm2xxx_wall_charger_suspend,
+ .resume = pm2xxx_wall_charger_resume,
+ .driver = {
+ .name = "pm2xxx-wall_charger",
+ .owner = THIS_MODULE,
+ },
+ .id_table = pm2xxx_id,
+};
+
+static int __init pm2xxx_charger_init(void)
+{
+ return i2c_add_driver(&pm2xxx_charger_driver);
+}
+
+static void __exit pm2xxx_charger_exit(void)
+{
+ i2c_del_driver(&pm2xxx_charger_driver);
+}
+
+subsys_initcall_sync(pm2xxx_charger_init);
+module_exit(pm2xxx_charger_exit);
+
+MODULE_LICENSE("GPL v2");
+MODULE_AUTHOR("Rajkumar kasirajan, Olivier Launay");
+MODULE_ALIAS("platform:pm2xxx-charger");
+MODULE_DESCRIPTION("PM2xxx charger management driver");
+
new file mode 100644
@@ -0,0 +1,60 @@
+/*
+ * PM2301 charger driver.
+ *
+ * Copyright (C) 2012 ST Ericsson Corporation
+ *
+ * Contact: Olivier LAUNAY (olivier.launay@stericsson.com
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
+ * General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA
+ * 02110-1301 USA
+ */
+
+#ifndef __LINUX_PM2301_H
+#define __LINUX_PM2301_H
+
+/**
+ * struct pm2xxx_bm_charger_parameters - Charger specific parameters
+ * @ac_volt_max: maximum allowed AC charger voltage in mV
+ * @ac_curr_max: maximum allowed AC charger current in mA
+ */
+struct pm2xxx_bm_charger_parameters {
+ int ac_volt_max;
+ int ac_curr_max;
+};
+
+/**
+ * struct pm2xxx_bm_data - pm2xxx battery management data
+ * @enable_overshoot flag to enable VBAT overshoot control
+ * @chg_params charger parameters
+ */
+struct pm2xxx_bm_data {
+ bool enable_overshoot;
+ const struct pm2xxx_bm_charger_parameters *chg_params;
+};
+
+struct pm2xxx_charger_platform_data {
+ char **supplied_to;
+ size_t num_supplicants;
+ int i2c_bus;
+ const char *label;
+ int irq_number;
+ int irq_type;
+};
+
+struct pm2xxx_platform_data {
+ struct pm2xxx_charger_platform_data *wall_charger;
+ struct pm2xxx_bm_data *battery;
+};
+
+#endif /* __LINUX_PM2301_H */