| Message ID | 1358485066-27495-1-git-send-email-avinashphilip@ti.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
* Philip Avinash <avinashphilip@ti.com> [130117 21:00]: > In case ELM module available, omap2 NAND driver can opt for hardware > correction method for bit flip errors in NAND flash with BCH. Hence the > detection of ELM module is done through devicetree population of elm_id. > This patch update device tree documentation for gpmc-nand for elm-id > data population. > > Signed-off-by: Philip Avinash <avinashphilip@ti.com> > --- > This patch based [1] and depends on [2]. As Artem suggested, this patch can > go in omap_tree due to the dependency on [3]. > Discussion can found at [4] > > Tony, > Can you accept this patch. Thanks applying into omap-for-v3.9/gpmc. Regards, Tony > 1. http://git.kernel.org/?p=linux/kernel/git/tmlind/linux-omap.git;a=shortlog;h=refs/heads/omap-for-v3.9/gpmc > 2. mtd: nand: omap2: Support for hardware BCH error correction > http://git.infradead.org/users/dedekind/l2-mtd-2.6.git/commit/576daed18c3f27bb5d0e57e1df11e8f7b493dce8 > 3. ARM: OMAP: gpmc: add DT bindings for GPMC timings and NAND > http://git.kernel.org/?p=linux/kernel/git/tmlind/linux-omap.git;a=commit;h=bc6b1e7b86f5d8e4a6fc1c0189e64bba4077efe0 > 4. https://lkml.org/lkml/2013/1/17/167 > > .../devicetree/bindings/mtd/gpmc-nand.txt | 4 ++++ > 1 file changed, 4 insertions(+) > > diff --git a/Documentation/devicetree/bindings/mtd/gpmc-nand.txt b/Documentation/devicetree/bindings/mtd/gpmc-nand.txt > index 9f464f9..e7f8d7e 100644 > --- a/Documentation/devicetree/bindings/mtd/gpmc-nand.txt > +++ b/Documentation/devicetree/bindings/mtd/gpmc-nand.txt > @@ -29,6 +29,9 @@ Optional properties: > "bch4" 4-bit BCH ecc code > "bch8" 8-bit BCH ecc code > > + - elm_id: Specifies elm device node. This is required to support BCH > + error correction using ELM module. > + > For inline partiton table parsing (optional): > > - #address-cells: should be set to 1 > @@ -46,6 +49,7 @@ Example for an AM33xx board: > #address-cells = <2>; > #size-cells = <1>; > ranges = <0 0 0x08000000 0x2000>; /* CS0: NAND */ > + elm_id = <&elm>; > > nand@0,0 { > reg = <0 0 0>; /* CS0, offset 0 */ > -- > 1.7.9.5 >
diff --git a/Documentation/devicetree/bindings/mtd/gpmc-nand.txt b/Documentation/devicetree/bindings/mtd/gpmc-nand.txt index 9f464f9..e7f8d7e 100644 --- a/Documentation/devicetree/bindings/mtd/gpmc-nand.txt +++ b/Documentation/devicetree/bindings/mtd/gpmc-nand.txt @@ -29,6 +29,9 @@ Optional properties: "bch4" 4-bit BCH ecc code "bch8" 8-bit BCH ecc code + - elm_id: Specifies elm device node. This is required to support BCH + error correction using ELM module. + For inline partiton table parsing (optional): - #address-cells: should be set to 1 @@ -46,6 +49,7 @@ Example for an AM33xx board: #address-cells = <2>; #size-cells = <1>; ranges = <0 0 0x08000000 0x2000>; /* CS0: NAND */ + elm_id = <&elm>; nand@0,0 { reg = <0 0 0>; /* CS0, offset 0 */
In case ELM module available, omap2 NAND driver can opt for hardware correction method for bit flip errors in NAND flash with BCH. Hence the detection of ELM module is done through devicetree population of elm_id. This patch update device tree documentation for gpmc-nand for elm-id data population. Signed-off-by: Philip Avinash <avinashphilip@ti.com> --- This patch based [1] and depends on [2]. As Artem suggested, this patch can go in omap_tree due to the dependency on [3]. Discussion can found at [4] Tony, Can you accept this patch. 1. http://git.kernel.org/?p=linux/kernel/git/tmlind/linux-omap.git;a=shortlog;h=refs/heads/omap-for-v3.9/gpmc 2. mtd: nand: omap2: Support for hardware BCH error correction http://git.infradead.org/users/dedekind/l2-mtd-2.6.git/commit/576daed18c3f27bb5d0e57e1df11e8f7b493dce8 3. ARM: OMAP: gpmc: add DT bindings for GPMC timings and NAND http://git.kernel.org/?p=linux/kernel/git/tmlind/linux-omap.git;a=commit;h=bc6b1e7b86f5d8e4a6fc1c0189e64bba4077efe0 4. https://lkml.org/lkml/2013/1/17/167 .../devicetree/bindings/mtd/gpmc-nand.txt | 4 ++++ 1 file changed, 4 insertions(+)