diff mbox

[3/3] ARM: davinci: da850: add mmc DT entries

Message ID 1359628387-14437-4-git-send-email-prakash.pm@ti.com (mailing list archive)
State New, archived
Headers show

Commit Message

Manjunathappa, Prakash Jan. 31, 2013, 10:33 a.m. UTC 
Add DT entry for MMC. Also add entry for pinmux information.
Tested on da850-evm without card detect and EDMA support as
DT support for GPIO and EDMA are yet come.

Signed-off-by: Manjunathappa, Prakash <prakash.pm@ti.com>
Cc: linux-mmc@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: davinci-linux-open-source@linux.davincidsp.com
Cc: devicetree-discuss@lists.ozlabs.org
Cc: cjb@laptop.org
Cc: Sekhar Nori <nsekhar@ti.com>
---
 arch/arm/boot/dts/da850-evm.dts |   13 +++++++++++++
 arch/arm/boot/dts/da850.dtsi    |   15 +++++++++++++++
 2 files changed, 28 insertions(+), 0 deletions(-)
diff mbox

Patch

diff --git a/arch/arm/boot/dts/da850-evm.dts b/arch/arm/boot/dts/da850-evm.dts
index fa04152..51c87e7 100644
--- a/arch/arm/boot/dts/da850-evm.dts
+++ b/arch/arm/boot/dts/da850-evm.dts
@@ -30,6 +30,19 @@ 
 		rtc0: rtc@1c23000 {
 			status = "okay";
 		};
+		mmc0: mmc@1c40000 {
+			status = "okay";
+			bus-width = <4>;
+			max-frequency = <50000000>;
+			/*
+			 * BIT(1) MMC_CAP_MMC_HIGHSPEED
+			 * BIT(2) MMC_CAP_SD_HIGHSPEED
+			 */
+			caps = <6>;
+			version = <1>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&mmc0_pins>;
+		};
 	};
 	nand_cs3@62000000 {
 		status = "okay";
diff --git a/arch/arm/boot/dts/da850.dtsi b/arch/arm/boot/dts/da850.dtsi
index 099c81e..5978a83 100644
--- a/arch/arm/boot/dts/da850.dtsi
+++ b/arch/arm/boot/dts/da850.dtsi
@@ -56,6 +56,15 @@ 
 					0x30 0x01100000  0x0ff00000
 				>;
 			};
+			mmc0_pins: pinmux_mmc_pins {
+				pinctrl-single,bits = <
+					/* MMCSD0_DAT[3] MMCSD0_DAT[2]
+					 * MMCSD0_DAT[1] MMCSD0_DAT[0]
+					 * MMCSD0_CMD    MMCSD0_CLK
+					 */
+					0x28 0x00222222  0x00ffffff
+				>;
+			};
 		};
 		serial0: serial@1c42000 {
 			compatible = "ns16550a";
@@ -88,6 +97,12 @@ 
 				      19>;
 			status = "disabled";
 		};
+		mmc0: mmc@1c40000 {
+			compatible = "ti,davinci_mmc";
+			reg = <0x40000 0x1000>;
+			interrupts = <16>;
+			status = "disabled";
+		};
 	};
 	nand_cs3@62000000 {
 		compatible = "ti,davinci-nand";