@@ -1,7 +1,9 @@
One-register-per-pin type device tree based pinctrl driver
Required properties:
-- compatible : "pinctrl-single"
+- compatible : "pinctrl-single" or "pinconf-single".
+ "pinctrl-single" means that pinconf isn't supported.
+ "pinconf-single" means that generic pinconf is supported.
- reg : offset and length of the register set for the mux registers
@@ -14,9 +16,72 @@ Optional properties:
- pinctrl-single,function-off : function off mode for disabled state if
available and same for all registers; if not specified, disabling of
pin functions is ignored
+
- pinctrl-single,bit-per-mux : boolean to indicate that one register controls
more than one pin
+- pinctrl-single,drive-strength : array of value that are used to configure
+ drive strength in the pinmux register. They're value of drive strength
+ current and drive strength mask.
+
+ /* drive strength current, mask */
+ pinctrl-single,power-source = <0x30 0xf0>;
+
+- pinctrl-single,bias-pullup : array of value that are used to configure the
+ input bias pullup in the pinmux register.
+
+ /* input, enabled pullup bits, disabled pullup bits, mask */
+ pinctrl-single,bias-pullup = <0 1 0 1>;
+
+- pinctrl-single,bias-pulldown : array of value that are used to configure the
+ input bias pulldown in the pinmux register.
+
+ /* input, enabled pulldown bits, disabled pulldown bits, mask */
+ pinctrl-single,bias-pulldown = <2 2 0 2>;
+
+- pinctrl-single,bias-autopull : array of value that are used to configure the
+ input bias autopull.
+
+ /* input, enabled autopull bits, disabled autopull bits, mask */
+ pinctrl-single,bias-autopull = <1 1 0 1>;
+
+ bias-pullup & bias-pulldown should be used together without bias-autoupll,
+ vice visa.
+
+ * Only one bit to control input bias enable or disable: User should use
+ pinctrl-single,bias-autoupll property at here.
+ * Two bits to control input bias pullup and pulldown: User should use
+ pinctrl-single,bias-pullup & pinctrl-single,bias-pulldown. One bit means
+ pullup, and the other one bit means pulldown.
+ * Three bits to control input bias enable, pullup and pulldown. User should
+ use pinctrl-single,bias-pullup & pinctrl-single,bias-pulldown. Input bias
+ enable bit should be included in pullup or pulldown bits.
+ * Although driver could set PIN_CONFIG_BIAS_DISABLE, there's no property as
+ pinctrl-single,bias-disable. Because pinctrl single driver could implement
+ it by calling pulldown, pullup, autopull disabled.
+
+- pinctrl-single,input-schmitt : array of value that are used to configure
+ input schmitt in the pinmux register. In some silicons, there're two input
+ schmitt value (rising-edge & falling-edge) in the pinmux register.
+
+ /* input schmitt value, mask */
+ pinctrl-single,input-schmitt = <0x30 0x70>;
+
+- pinctrl-single,input-schmitt-enable : array of value that are used to
+ configure input schmitt enable or disable in the pinmux register.
+
+ /* input, enable bits, disable bits, mask */
+ pinctrl-single,input-schmitt-enable = <0x30 0x40 0 0x70>;
+
+- pinctrl-single,gpio-range : list of value that are used to configure a GPIO
+ range. They're value of subnode phandle, pin base in pinctrl device, pin
+ number in this range, GPIO function value of this GPIO range.
+ The number of parameters is depend on #pinctrl-single,gpio-range-cells
+ property.
+
+ /* pin base, nr pins & gpio function */
+ pinctrl-single,gpio-range = <&range 0 3 0 &range 3 9 1>;
+
This driver assumes that there is only one register for each pin (unless the
pinctrl-single,bit-per-mux is set), and uses the common pinctrl bindings as
specified in the pinctrl-bindings.txt document in this directory.
@@ -42,6 +107,20 @@ Where 0xdc is the offset from the pinctrl register base address for the
device pinctrl register, 0x18 is the desired value, and 0xff is the sub mask to
be used when applying this change to the register.
+
+Optional sub-node: In case some pins could be configured as GPIO in the pinmux
+register, those pins could be defined as a GPIO range. This sub-node is required
+by pinctrl-single,gpio-range property.
+
+Required properties in sub-node:
+- #pinctrl-single,gpio-range-cells : the number of parameters after phandle in
+ pinctrl-single,gpio-range property.
+
+ range: gpio-range {
+ #pinctrl-single,gpio-range-cells = <3>;
+ };
+
+
Example:
/* SoC common file */
@@ -76,6 +155,29 @@ control_devconf0: pinmux@48002274 {
pinctrl-single,function-mask = <0x5F>;
};
+/* third controller instance for pins in gpio domain */
+pmx_gpio: pinmux@d401e000 {
+ compatible = "pinconf-single";
+ reg = <0xd401e000 0x0330>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ pinctrl-single,register-width = <32>;
+ pinctrl-single,function-mask = <7>;
+
+ /* sparse GPIO range could be supported */
+ pinctrl-single,gpio-range = <&range 0 3 0 &range 3 9 1
+ &range 12 1 0 &range 13 29 1
+ &range 43 1 0 &range 44 49 1
+ &range 94 1 1 &range 96 2 1>;
+
+ range: gpio-range {
+ #pinctrl-single,gpio-range-cells = <3>;
+ };
+};
+
+
/* board specific .dts file */
&pmx_core {
@@ -96,6 +198,15 @@ control_devconf0: pinmux@48002274 {
>;
};
+ uart0_pins: pinmux_uart0_pins {
+ pinctrl-single,pins = <
+ 0x208 0 /* UART0_RXD (IOCFG138) */
+ 0x20c 0 /* UART0_TXD (IOCFG139) */
+ >;
+ pinctrl-single,bias-pulldown = <0 2 2>;
+ pinctrl-single,bias-pullup = <0 1 1>;
+ };
+
/* map uart2 pins */
uart2_pins: pinmux_uart2_pins {
pinctrl-single,pins = <
@@ -122,6 +233,11 @@ control_devconf0: pinmux@48002274 {
};
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins>;
+};
+
&uart2 {
pinctrl-names = "default";
pinctrl-0 = <&uart2_pins>;