deleted file mode 100644
@@ -1,24 +0,0 @@
-VIA/Wondermedia VT8500 GPIO Controller
------------------------------------------------------
-
-Required properties:
-- compatible : "via,vt8500-gpio", "wm,wm8505-gpio"
- or "wm,wm8650-gpio" depending on your SoC
-- reg : Should contain 1 register range (address and length)
-- #gpio-cells : should be <3>.
- 1) bank
- 2) pin number
- 3) flags - should be 0
-
-Example:
-
- gpio: gpio-controller@d8110000 {
- compatible = "via,vt8500-gpio";
- gpio-controller;
- reg = <0xd8110000 0x10000>;
- #gpio-cells = <3>;
- };
-
- vibrate {
- gpios = <&gpio 0 1 0>; /* Bank 0, Pin 1, No flags */
- };
@@ -227,12 +227,6 @@ config GPIO_TS5500
blocks of the TS-5500: DIO1, DIO2 and the LCD port, and the TS-5600
LCD port.
-config GPIO_VT8500
- bool "VIA/Wondermedia SoC GPIO Support"
- depends on ARCH_VT8500
- help
- Say yes here to support the VT8500/WM8505/WM8650 GPIO controller.
-
config GPIO_XILINX
bool "Xilinx GPIO support"
depends on PPC_OF || MICROBLAZE
@@ -80,7 +80,6 @@ obj-$(CONFIG_GPIO_TWL6040) += gpio-twl6040.o
obj-$(CONFIG_GPIO_UCB1400) += gpio-ucb1400.o
obj-$(CONFIG_GPIO_VIPERBOARD) += gpio-viperboard.o
obj-$(CONFIG_GPIO_VR41XX) += gpio-vr41xx.o
-obj-$(CONFIG_GPIO_VT8500) += gpio-vt8500.o
obj-$(CONFIG_GPIO_VX855) += gpio-vx855.o
obj-$(CONFIG_GPIO_WM831X) += gpio-wm831x.o
obj-$(CONFIG_GPIO_WM8350) += gpio-wm8350.o
deleted file mode 100644
@@ -1,355 +0,0 @@
-/* drivers/gpio/gpio-vt8500.c
- *
- * Copyright (C) 2012 Tony Prisk <linux@prisktech.co.nz>
- * Based on arch/arm/mach-vt8500/gpio.c:
- * - Copyright (C) 2010 Alexey Charkov <alchark@gmail.com>
- *
- * This software is licensed under the terms of the GNU General Public
- * License version 2, as published by the Free Software Foundation, and
- * may be copied, distributed, and modified under those terms.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- */
-
-#include <linux/module.h>
-#include <linux/err.h>
-#include <linux/io.h>
-#include <linux/gpio.h>
-#include <linux/platform_device.h>
-#include <linux/bitops.h>
-#include <linux/of.h>
-#include <linux/of_address.h>
-#include <linux/of_irq.h>
-#include <linux/of_device.h>
-
-/*
- We handle GPIOs by bank, each bank containing up to 32 GPIOs covered
- by one set of registers (although not all may be valid).
-
- Because different SoC's have different register offsets, we pass the
- register offsets as data in vt8500_gpio_dt_ids[].
-
- A value of NO_REG is used to indicate that this register is not
- supported. Only used for ->en at the moment.
-*/
-
-#define NO_REG 0xFFFF
-
-/*
- * struct vt8500_gpio_bank_regoffsets
- * @en: offset to enable register of the bank
- * @dir: offset to direction register of the bank
- * @data_out: offset to the data out register of the bank
- * @data_in: offset to the data in register of the bank
- * @ngpio: highest valid pin in this bank
- */
-
-struct vt8500_gpio_bank_regoffsets {
- unsigned int en;
- unsigned int dir;
- unsigned int data_out;
- unsigned int data_in;
- unsigned char ngpio;
-};
-
-struct vt8500_gpio_data {
- unsigned int num_banks;
- struct vt8500_gpio_bank_regoffsets banks[];
-};
-
-#define VT8500_BANK(__en, __dir, __out, __in, __ngpio) \
-{ \
- .en = __en, \
- .dir = __dir, \
- .data_out = __out, \
- .data_in = __in, \
- .ngpio = __ngpio, \
-}
-
-static struct vt8500_gpio_data vt8500_data = {
- .num_banks = 7,
- .banks = {
- VT8500_BANK(NO_REG, 0x3C, 0x5C, 0x7C, 9),
- VT8500_BANK(0x00, 0x20, 0x40, 0x60, 26),
- VT8500_BANK(0x04, 0x24, 0x44, 0x64, 28),
- VT8500_BANK(0x08, 0x28, 0x48, 0x68, 31),
- VT8500_BANK(0x0C, 0x2C, 0x4C, 0x6C, 19),
- VT8500_BANK(0x10, 0x30, 0x50, 0x70, 19),
- VT8500_BANK(0x14, 0x34, 0x54, 0x74, 23),
- },
-};
-
-static struct vt8500_gpio_data wm8505_data = {
- .num_banks = 10,
- .banks = {
- VT8500_BANK(0x64, 0x8C, 0xB4, 0xDC, 22),
- VT8500_BANK(0x40, 0x68, 0x90, 0xB8, 8),
- VT8500_BANK(0x44, 0x6C, 0x94, 0xBC, 32),
- VT8500_BANK(0x48, 0x70, 0x98, 0xC0, 6),
- VT8500_BANK(0x4C, 0x74, 0x9C, 0xC4, 16),
- VT8500_BANK(0x50, 0x78, 0xA0, 0xC8, 25),
- VT8500_BANK(0x54, 0x7C, 0xA4, 0xCC, 5),
- VT8500_BANK(0x58, 0x80, 0xA8, 0xD0, 5),
- VT8500_BANK(0x5C, 0x84, 0xAC, 0xD4, 12),
- VT8500_BANK(0x60, 0x88, 0xB0, 0xD8, 16),
- VT8500_BANK(0x500, 0x504, 0x508, 0x50C, 6),
- },
-};
-
-/*
- * No information about which bits are valid so we just make
- * them all available until its figured out.
- */
-static struct vt8500_gpio_data wm8650_data = {
- .num_banks = 9,
- .banks = {
- VT8500_BANK(0x40, 0x80, 0xC0, 0x00, 32),
- VT8500_BANK(0x44, 0x84, 0xC4, 0x04, 32),
- VT8500_BANK(0x48, 0x88, 0xC8, 0x08, 32),
- VT8500_BANK(0x4C, 0x8C, 0xCC, 0x0C, 32),
- VT8500_BANK(0x50, 0x90, 0xD0, 0x10, 32),
- VT8500_BANK(0x54, 0x94, 0xD4, 0x14, 32),
- VT8500_BANK(0x58, 0x98, 0xD8, 0x18, 32),
- VT8500_BANK(0x5C, 0x9C, 0xDC, 0x1C, 32),
- VT8500_BANK(0x7C, 0xBC, 0xFC, 0x3C, 32),
- VT8500_BANK(0x500, 0x504, 0x508, 0x50C, 6),
- },
-};
-
-struct vt8500_gpio_chip {
- struct gpio_chip chip;
-
- const struct vt8500_gpio_bank_regoffsets *regs;
- void __iomem *base;
-};
-
-struct vt8500_data {
- struct vt8500_gpio_chip *chip;
- void __iomem *iobase;
- int num_banks;
-};
-
-
-#define to_vt8500(__chip) container_of(__chip, struct vt8500_gpio_chip, chip)
-
-static int vt8500_gpio_request(struct gpio_chip *chip, unsigned offset)
-{
- u32 val;
- struct vt8500_gpio_chip *vt8500_chip = to_vt8500(chip);
-
- if (vt8500_chip->regs->en == NO_REG)
- return 0;
-
- val = readl_relaxed(vt8500_chip->base + vt8500_chip->regs->en);
- val |= BIT(offset);
- writel_relaxed(val, vt8500_chip->base + vt8500_chip->regs->en);
-
- return 0;
-}
-
-static void vt8500_gpio_free(struct gpio_chip *chip, unsigned offset)
-{
- struct vt8500_gpio_chip *vt8500_chip = to_vt8500(chip);
- u32 val;
-
- if (vt8500_chip->regs->en == NO_REG)
- return;
-
- val = readl_relaxed(vt8500_chip->base + vt8500_chip->regs->en);
- val &= ~BIT(offset);
- writel_relaxed(val, vt8500_chip->base + vt8500_chip->regs->en);
-}
-
-static int vt8500_gpio_direction_input(struct gpio_chip *chip, unsigned offset)
-{
- struct vt8500_gpio_chip *vt8500_chip = to_vt8500(chip);
-
- u32 val = readl_relaxed(vt8500_chip->base + vt8500_chip->regs->dir);
- val &= ~BIT(offset);
- writel_relaxed(val, vt8500_chip->base + vt8500_chip->regs->dir);
-
- return 0;
-}
-
-static int vt8500_gpio_direction_output(struct gpio_chip *chip, unsigned offset,
- int value)
-{
- struct vt8500_gpio_chip *vt8500_chip = to_vt8500(chip);
-
- u32 val = readl_relaxed(vt8500_chip->base + vt8500_chip->regs->dir);
- val |= BIT(offset);
- writel_relaxed(val, vt8500_chip->base + vt8500_chip->regs->dir);
-
- if (value) {
- val = readl_relaxed(vt8500_chip->base +
- vt8500_chip->regs->data_out);
- val |= BIT(offset);
- writel_relaxed(val, vt8500_chip->base +
- vt8500_chip->regs->data_out);
- }
- return 0;
-}
-
-static int vt8500_gpio_get_value(struct gpio_chip *chip, unsigned offset)
-{
- struct vt8500_gpio_chip *vt8500_chip = to_vt8500(chip);
-
- return (readl_relaxed(vt8500_chip->base + vt8500_chip->regs->data_in) >>
- offset) & 1;
-}
-
-static void vt8500_gpio_set_value(struct gpio_chip *chip, unsigned offset,
- int value)
-{
- struct vt8500_gpio_chip *vt8500_chip = to_vt8500(chip);
-
- u32 val = readl_relaxed(vt8500_chip->base +
- vt8500_chip->regs->data_out);
- if (value)
- val |= BIT(offset);
- else
- val &= ~BIT(offset);
-
- writel_relaxed(val, vt8500_chip->base + vt8500_chip->regs->data_out);
-}
-
-static int vt8500_of_xlate(struct gpio_chip *gc,
- const struct of_phandle_args *gpiospec, u32 *flags)
-{
- /* bank if specificed in gpiospec->args[0] */
- if (flags)
- *flags = gpiospec->args[2];
-
- return gpiospec->args[1];
-}
-
-static int vt8500_add_chips(struct platform_device *pdev, void __iomem *base,
- const struct vt8500_gpio_data *data)
-{
- struct vt8500_data *priv;
- struct vt8500_gpio_chip *vtchip;
- struct gpio_chip *chip;
- int i;
- int pin_cnt = 0;
-
- priv = devm_kzalloc(&pdev->dev, sizeof(struct vt8500_data), GFP_KERNEL);
- if (!priv) {
- dev_err(&pdev->dev, "failed to allocate memory\n");
- return -ENOMEM;
- }
-
- priv->chip = devm_kzalloc(&pdev->dev,
- sizeof(struct vt8500_gpio_chip) * data->num_banks,
- GFP_KERNEL);
- if (!priv->chip) {
- dev_err(&pdev->dev, "failed to allocate chip memory\n");
- return -ENOMEM;
- }
-
- priv->iobase = base;
- priv->num_banks = data->num_banks;
- platform_set_drvdata(pdev, priv);
-
- vtchip = priv->chip;
-
- for (i = 0; i < data->num_banks; i++) {
- vtchip[i].base = base;
- vtchip[i].regs = &data->banks[i];
-
- chip = &vtchip[i].chip;
-
- chip->of_xlate = vt8500_of_xlate;
- chip->of_gpio_n_cells = 3;
- chip->of_node = pdev->dev.of_node;
-
- chip->request = vt8500_gpio_request;
- chip->free = vt8500_gpio_free;
- chip->direction_input = vt8500_gpio_direction_input;
- chip->direction_output = vt8500_gpio_direction_output;
- chip->get = vt8500_gpio_get_value;
- chip->set = vt8500_gpio_set_value;
- chip->can_sleep = 0;
- chip->base = pin_cnt;
- chip->ngpio = data->banks[i].ngpio;
-
- pin_cnt += data->banks[i].ngpio;
-
- gpiochip_add(chip);
- }
- return 0;
-}
-
-static struct of_device_id vt8500_gpio_dt_ids[] = {
- { .compatible = "via,vt8500-gpio", .data = &vt8500_data, },
- { .compatible = "wm,wm8505-gpio", .data = &wm8505_data, },
- { .compatible = "wm,wm8650-gpio", .data = &wm8650_data, },
- { /* Sentinel */ },
-};
-
-static int vt8500_gpio_probe(struct platform_device *pdev)
-{
- int ret;
- void __iomem *gpio_base;
- struct resource *res;
- const struct of_device_id *of_id =
- of_match_device(vt8500_gpio_dt_ids, &pdev->dev);
-
- if (!of_id) {
- dev_err(&pdev->dev, "No matching driver data\n");
- return -ENODEV;
- }
-
- res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
- if (!res) {
- dev_err(&pdev->dev, "Unable to get IO resource\n");
- return -ENODEV;
- }
-
- gpio_base = devm_request_and_ioremap(&pdev->dev, res);
- if (!gpio_base) {
- dev_err(&pdev->dev, "Unable to map GPIO registers\n");
- return -ENOMEM;
- }
-
- ret = vt8500_add_chips(pdev, gpio_base, of_id->data);
-
- return ret;
-}
-
-static int vt8500_gpio_remove(struct platform_device *pdev)
-{
- int i;
- int ret;
- struct vt8500_data *priv = platform_get_drvdata(pdev);
- struct vt8500_gpio_chip *vtchip = priv->chip;
-
- for (i = 0; i < priv->num_banks; i++) {
- ret = gpiochip_remove(&vtchip[i].chip);
- if (ret)
- dev_warn(&pdev->dev, "gpiochip_remove returned %d\n",
- ret);
- }
-
- return 0;
-}
-
-static struct platform_driver vt8500_gpio_driver = {
- .probe = vt8500_gpio_probe,
- .remove = vt8500_gpio_remove,
- .driver = {
- .name = "vt8500-gpio",
- .owner = THIS_MODULE,
- .of_match_table = vt8500_gpio_dt_ids,
- },
-};
-
-module_platform_driver(vt8500_gpio_driver);
-
-MODULE_DESCRIPTION("VT8500 GPIO Driver");
-MODULE_AUTHOR("Tony Prisk <linux@prisktech.co.nz>");
-MODULE_LICENSE("GPL v2");
-MODULE_DEVICE_TABLE(of, vt8500_gpio_dt_ids);
With the move to a combined pinctrl/gpio driver, the arch-vt8500 gpio driver is no longer required. Signed-off-by: Tony Prisk <linux@prisktech.co.nz> --- .../devicetree/bindings/gpio/gpio-vt8500.txt | 24 -- drivers/gpio/Kconfig | 6 - drivers/gpio/Makefile | 1 - drivers/gpio/gpio-vt8500.c | 355 -------------------- 4 files changed, 386 deletions(-) delete mode 100644 Documentation/devicetree/bindings/gpio/gpio-vt8500.txt delete mode 100644 drivers/gpio/gpio-vt8500.c