@@ -78,6 +78,13 @@ CONFIG_BACKLIGHT_LCD_SUPPORT=y
CONFIG_LCD_CLASS_DEVICE=y
CONFIG_BACKLIGHT_CLASS_DEVICE=y
# CONFIG_USB_SUPPORT is not set
+CONFIG_MMC=y
+CONFIG_MMC_UNSAFE_RESUME=y
+CONFIG_MMC_BLOCK_MINORS=32
+CONFIG_MMC_TEST=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_PLTFM=y
+CONFIG_MMC_SDHCI_BCM_KONA=y
CONFIG_NEW_LEDS=y
CONFIG_LEDS_CLASS=y
CONFIG_LEDS_TRIGGERS=y
@@ -238,6 +238,17 @@ config MMC_SDHCI_S3C_DMA
YMMV.
+config MMC_SDHCI_BCM_KONA
+ tristate "SDHCI support on Broadcom KONA platform"
+ depends on ARCH_BCM
+ select MMC_SDHCI_PLTFM
+ help
+ This selects the Broadcom Kona Secure Digital Host Controller
+ Interface(SDHCI) support.
+ This is used in Broadcom mobile SoCs.
+
+ If you have a controller with this interface, say Y or M here.
+
config MMC_SDHCI_BCM2835
tristate "SDHCI platform support for the BCM2835 SD/MMC Controller"
depends on ARCH_BCM2835
@@ -59,6 +59,7 @@ obj-$(CONFIG_MMC_SDHCI_DOVE) += sdhci-dove.o
obj-$(CONFIG_MMC_SDHCI_TEGRA) += sdhci-tegra.o
obj-$(CONFIG_MMC_SDHCI_OF_ESDHC) += sdhci-of-esdhc.o
obj-$(CONFIG_MMC_SDHCI_OF_HLWD) += sdhci-of-hlwd.o
+obj-$(CONFIG_MMC_SDHCI_BCM_KONA) += sdhci-bcm-kona.o
obj-$(CONFIG_MMC_SDHCI_BCM2835) += sdhci-bcm2835.o
ifeq ($(CONFIG_CB710_DEBUG),y)
new file mode 100644
@@ -0,0 +1,485 @@
+/*
+ * Copyright (C) 2013 Broadcom Corporation
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation version 2.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
+ * kind, whether express or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/delay.h>
+#include <linux/highmem.h>
+#include <linux/platform_device.h>
+#include <linux/mmc/host.h>
+#include <linux/io.h>
+#include <linux/gpio.h>
+#include <linux/clk.h>
+#include <linux/regulator/consumer.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/of_gpio.h>
+#include <linux/version.h>
+
+#include "sdhci-pltfm.h"
+#include "sdhci.h"
+
+#define SDHCI_SOFT_RESET 0x01000000
+#define KONA_SDHOST_CORECTRL 0x8000
+#define KONA_SDHOST_CD_PINCTRL 0x00000008
+#define KONA_SDHOST_STOP_HCLK 0x00000004
+#define KONA_SDHOST_RESET 0x00000002
+#define KONA_SDHOST_EN 0x00000001
+
+#define KONA_SDHOST_CORESTAT 0x8004
+#define KONA_SDHOST_WP 0x00000002
+#define KONA_SDHOST_CD_SW 0x00000001
+
+#define KONA_SDHOST_COREIMR 0x8008
+#define KONA_SDHOST_IP 0x00000001
+
+#define KONA_SDHOST_COREISR 0x800C
+#define KONA_SDHOST_COREIMSR 0x8010
+#define KONA_SDHOST_COREDBG1 0x8014
+#define KONA_SDHOST_COREGPO_MASK 0x8018
+
+#define SD_DETECT_GPIO_DEBOUNCE_128MS 128
+
+#define KONA_MMC_AUTOSUSPEND_DELAY (50)
+
+struct sdhci_bcm_kona_cfg {
+ unsigned int max_freq;
+ int is_8bit;
+ int irq;
+ int cd_gpio;
+ int wp_gpio;
+ int non_removable;
+};
+
+struct sdhci_bcm_kona_dev {
+ struct sdhci_bcm_kona_cfg *cfg;
+ struct device *dev;
+ struct sdhci_host *host;
+ struct clk *peri_clk;
+ struct clk *sleep_clk;
+};
+
+
+static int sdhci_bcm_kona_sd_reset(struct sdhci_host *host)
+{
+ unsigned int val;
+ unsigned long timeout;
+
+ /* This timeout should be sufficent for core to reset */
+ timeout = jiffies + msecs_to_jiffies(100);
+
+ /* reset the host using the top level reset */
+ val = sdhci_readl(host, KONA_SDHOST_CORECTRL);
+ val |= KONA_SDHOST_RESET;
+ sdhci_writel(host, val, KONA_SDHOST_CORECTRL);
+
+ while (!(sdhci_readl(host, KONA_SDHOST_CORECTRL) & KONA_SDHOST_RESET)) {
+ if (time_is_before_jiffies(timeout)) {
+ pr_err("Error: sd host is stuck in reset!!!\n");
+ return -EFAULT;
+ }
+ }
+
+ /* bring the host out of reset */
+ val = sdhci_readl(host, KONA_SDHOST_CORECTRL);
+ val &= ~KONA_SDHOST_RESET;
+
+ /*
+ * Back-to-Back register write needs a delay of 1ms at bootup (min 10uS)
+ * Back-to-Back writes to same register needs delay when SD bus clock
+ * is very low w.r.t AHB clock, mainly during boot-time and during card
+ * insert-removal.
+ */
+ mdelay(1);
+ sdhci_writel(host, val, KONA_SDHOST_CORECTRL);
+
+ return 0;
+}
+
+static void sdhci_bcm_kona_sd_init(struct sdhci_host *host)
+{
+ unsigned int val;
+
+ /* enable the interrupt from the IP core */
+ val = sdhci_readl(host, KONA_SDHOST_COREIMR);
+ val |= KONA_SDHOST_IP;
+ sdhci_writel(host, val, KONA_SDHOST_COREIMR);
+
+ /* Enable the AHB clock gating module to the host */
+ val = sdhci_readl(host, KONA_SDHOST_CORECTRL);
+ val |= KONA_SDHOST_EN;
+
+ /*
+ * Back-to-Back register write needs a delay of 1ms at bootup (min 10uS)
+ * Back-to-Back writes to same register needs delay when SD bus clock
+ * is very low w.r.t AHB clock, mainly during boot-time and during card
+ * insert-removal.
+ */
+ mdelay(1);
+ sdhci_writel(host, val, KONA_SDHOST_CORECTRL);
+}
+
+/*
+ * Software emulation of the SD card insertion/removal. Set insert=1 for insert
+ * and insert=0 for removal. The card detection is done by GPIO. For Broadcom
+ * IP to function properly the bit 0 of CORESTAT register needs to be set/reset
+ * to generate the CD IRQ handled in sdhci.c which schedules card_tasklet.
+ */
+static int sdhci_bcm_kona_sd_card_emulate(struct sdhci_host *host, int insert)
+{
+ struct sdhci_pltfm_host *pltfm_priv = sdhci_priv(host);
+ struct sdhci_bcm_kona_dev *kona_dev = pltfm_priv->priv;
+ u32 val;
+ unsigned long flags;
+
+ /* this function can be called from various contexts including ISR */
+ spin_lock_irqsave(&host->lock, flags);
+ /* Ensure SD bus scanning to detect media change */
+ host->mmc->rescan_disable = 0;
+
+ /*
+ * Back-to-Back register write needs a delay of min 10uS.
+ * Back-to-Back writes to same register needs delay when SD bus clock
+ * is very low w.r.t AHB clock, mainly during boot-time and during card
+ * insert-removal.
+ * We keep 20uS
+ */
+ udelay(20);
+ val = sdhci_readl(host, KONA_SDHOST_CORESTAT);
+
+ if (insert) {
+ if (gpio_is_valid(kona_dev->cfg->wp_gpio)) {
+ int wp_status = gpio_get_value(kona_dev->cfg->wp_gpio);
+
+ if (wp_status)
+ val |= KONA_SDHOST_WP;
+ else
+ val &= ~KONA_SDHOST_WP;
+ }
+
+ val |= KONA_SDHOST_CD_SW;
+ sdhci_writel(host, val, KONA_SDHOST_CORESTAT);
+ } else {
+ val &= ~KONA_SDHOST_CD_SW;
+ sdhci_writel(host, val, KONA_SDHOST_CORESTAT);
+ }
+ spin_unlock_irqrestore(&host->lock, flags);
+
+ return 0;
+}
+
+/*
+ * SD card detection interrupt handler
+ */
+static irqreturn_t sdhci_bcm_kona_pltfm_cd_interrupt(int irq, void *host)
+{
+ struct sdhci_pltfm_host *pltfm_priv = sdhci_priv(host);
+ struct sdhci_bcm_kona_dev *kona_dev = pltfm_priv->priv;
+
+ if (gpio_get_value_cansleep(kona_dev->cfg->cd_gpio) == 0) {
+ dev_dbg(kona_dev->dev, "card inserted\n");
+ sdhci_bcm_kona_sd_card_emulate(host, 1);
+ } else {
+ dev_dbg(kona_dev->dev, "card removed\n");
+ sdhci_bcm_kona_sd_card_emulate(host, 0);
+ }
+
+ return IRQ_HANDLED;
+}
+
+/*
+ * Get the base clock. Use central clock source for now. Not sure if different
+ * clock speed to each dev is allowed
+ */
+static unsigned int sdhci_bcm_kona_get_max_clk(struct sdhci_host *host)
+{
+ struct sdhci_bcm_kona_dev *kona_dev;
+ struct sdhci_pltfm_host *pltfm_priv = sdhci_priv(host);
+ kona_dev = pltfm_priv->priv;
+
+ return kona_dev->cfg->max_freq;
+}
+
+static unsigned int sdhci_bcm_kona_get_timeout_clock(struct sdhci_host *host)
+{
+ return sdhci_bcm_kona_get_max_clk(host);
+}
+
+static void sdhci_bcm_kona_init_74_clocks(struct sdhci_host *host,
+ u8 power_mode)
+{
+ if (power_mode == MMC_POWER_OFF)
+ return;
+ else
+ mdelay(10);
+}
+
+static struct sdhci_ops sdhci_bcm_kona_ops = {
+ .get_max_clock = sdhci_bcm_kona_get_max_clk,
+ .get_timeout_clock = sdhci_bcm_kona_get_timeout_clock,
+ .platform_send_init_74_clocks = sdhci_bcm_kona_init_74_clocks,
+};
+
+static struct sdhci_pltfm_data sdhci_pltfm_data_kona = {
+ .ops = &sdhci_bcm_kona_ops,
+ .quirks = SDHCI_QUIRK_NO_CARD_NO_RESET |
+ SDHCI_QUIRK_BROKEN_TIMEOUT_VAL | SDHCI_QUIRK_32BIT_DMA_ADDR |
+ SDHCI_QUIRK_32BIT_DMA_SIZE | SDHCI_QUIRK_32BIT_ADMA_SIZE |
+ SDHCI_QUIRK_FORCE_BLK_SZ_2048 |
+ SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN,
+};
+
+static const struct of_device_id sdhci_bcm_kona_of_match[] __initdata = {
+ { .compatible = "bcm,kona-sdhci", .data = &sdhci_pltfm_data_kona },
+ {}
+};
+MODULE_DEVICE_TABLE(of, sdhci_bcm_kona_of_match);
+
+static struct sdhci_bcm_kona_cfg * __init sdhci_bcm_kona_parse_dt(
+ struct platform_device *pdev)
+{
+ struct sdhci_bcm_kona_cfg *cfg;
+ struct device_node *np = pdev->dev.of_node;
+ u32 temp;
+
+ if (!np)
+ return NULL;
+
+ cfg = devm_kzalloc(&pdev->dev, sizeof(*cfg), GFP_KERNEL);
+ if (!cfg) {
+ dev_err(&pdev->dev, "Can't allocate platform cfg\n");
+ return NULL;
+ }
+
+ cfg->cd_gpio = of_get_named_gpio(np, "cd-gpios", 0);
+ cfg->wp_gpio = of_get_named_gpio(np, "wp-gpios", 0);
+ if (of_property_read_bool(np, "non-removable"))
+ cfg->non_removable = 1;
+
+ if (of_property_read_u32(np, "bus-width", &temp) == 0 && temp == 8)
+ cfg->is_8bit = 1;
+
+ if (of_property_read_u32(np, "max-frequency", &cfg->max_freq)) {
+ dev_err(&pdev->dev, "Missing max-freq for SDHCI cfg\n");
+ return NULL;
+ }
+ return cfg;
+}
+
+static int __init sdhci_bcm_kona_probe(struct platform_device *pdev)
+{
+ const struct of_device_id *match;
+ struct sdhci_bcm_kona_cfg *kona_cfg = NULL;
+ const struct sdhci_pltfm_data *plat_data;
+ struct sdhci_bcm_kona_dev *kona_dev = NULL;
+ struct sdhci_pltfm_host *pltfm_priv;
+ struct device *dev = &pdev->dev;
+ struct sdhci_host *host;
+ int ret;
+ unsigned int irq;
+ ret = 0;
+
+ match = of_match_device(sdhci_bcm_kona_of_match, &pdev->dev);
+ if (!match)
+ plat_data = &sdhci_pltfm_data_kona;
+ else
+ plat_data = match->data;
+
+ host = sdhci_pltfm_init(pdev, (struct sdhci_pltfm_data *)plat_data);
+ if (IS_ERR(host))
+ return PTR_ERR(host);
+
+ kona_cfg = dev->platform_data;
+ if (!kona_cfg)
+ kona_cfg = sdhci_bcm_kona_parse_dt(pdev);
+
+ if (!kona_cfg) {
+ ret = -ENXIO;
+ goto err_pltfm_free;
+ }
+
+ dev_dbg(dev, "%s: inited. IOADDR=%p\n", __func__, host->ioaddr);
+
+ pltfm_priv = sdhci_priv(host);
+
+ kona_dev = devm_kzalloc(dev, sizeof(*kona_dev), GFP_KERNEL);
+ if (!kona_dev) {
+ dev_err(dev, "Can't allocate kona_dev\n");
+ ret = -ENOMEM;
+ goto err_pltfm_free;
+ }
+ kona_dev->cfg = kona_cfg;
+ kona_dev->dev = dev;
+ pltfm_priv->priv = kona_dev;
+
+ dev_dbg(dev, "non-removable=%c\n",
+ (kona_cfg->non_removable) ? 'Y' : 'N');
+ dev_dbg(dev, "cd_gpio %d, wp_gpio %d\n", kona_cfg->cd_gpio,
+ kona_cfg->wp_gpio);
+
+ if (kona_cfg->non_removable) {
+ host->mmc->caps |= MMC_CAP_NONREMOVABLE;
+ host->quirks |= SDHCI_QUIRK_BROKEN_CARD_DETECTION;
+ }
+
+ dev_dbg(dev, "is_8bit=%c\n", (kona_cfg->is_8bit) ? 'Y' : 'N');
+ if (kona_cfg->is_8bit)
+ host->mmc->caps |= MMC_CAP_8_BIT_DATA;
+
+ ret = sdhci_bcm_kona_sd_reset(host);
+ if (ret)
+ goto err_pltfm_free;
+
+ sdhci_bcm_kona_sd_init(host);
+
+ ret = sdhci_add_host(host);
+ if (ret) {
+ dev_err(dev, "Failed sdhci_add_host\n");
+ goto err_reset;
+ }
+
+ /* if device is eMMC, emulate card insert right here */
+ if (kona_cfg->non_removable) {
+ ret = sdhci_bcm_kona_sd_card_emulate(host, 1);
+ if (ret) {
+ dev_err(dev,
+ "unable to emulate card insertion\n");
+ goto err_remove_host;
+ }
+ } else if (gpio_is_valid(kona_dev->cfg->cd_gpio)) {
+ ret = devm_gpio_request(dev, kona_dev->cfg->cd_gpio, "sdio cd");
+ if (ret < 0) {
+ dev_err(kona_dev->dev,
+ "Unable to request GPIO pin %d\n",
+ kona_dev->cfg->cd_gpio);
+ goto err_remove_host;
+ }
+
+ gpio_direction_input(kona_dev->cfg->cd_gpio);
+
+ /* Set debounce for SD Card detect to maximum value (128ms)
+ *
+ * NOTE-1: If gpio_set_debounce() returns error we still
+ * continue with the default debounce value set. Another reason
+ * for doing this is that on rhea-ray boards the SD Detect GPIO
+ * is on GPIO Expander and gpio_set_debounce() will return error
+ * and if we return error from here, then probe() would fail and
+ * SD detection would always fail.
+ *
+ * NOTE-2: We also give a msleep() of the "debounce" time here
+ * so that we give enough time for the debounce to stabilize
+ * before we read the gpio value in gpio_get_value_cansleep().
+ */
+ ret = gpio_set_debounce(kona_dev->cfg->cd_gpio,
+ (SD_DETECT_GPIO_DEBOUNCE_128MS * 1000));
+ if (ret < 0) {
+ dev_err(kona_dev->dev,
+ "%s: gpio set debounce failed."
+ "default debounce value assumed\n", __func__);
+ }
+
+ /* Sleep for 128ms to allow debounce to stabilize */
+ msleep(SD_DETECT_GPIO_DEBOUNCE_128MS);
+ /* request irq for cd_gpio after the gpio debounce is
+ * stabilized, otherwise, some bogus gpio interrupts might be
+ * triggered.
+ */
+ irq = gpio_to_irq(kona_dev->cfg->cd_gpio);
+ ret = devm_request_threaded_irq(dev,
+ irq,
+ NULL,
+ sdhci_bcm_kona_pltfm_cd_interrupt,
+ IRQF_TRIGGER_FALLING|
+ IRQF_TRIGGER_RISING |
+ IRQF_ONESHOT |
+ IRQF_NO_SUSPEND, "sdio cd", host);
+ if (ret) {
+ dev_err(kona_dev->dev,
+ "Failed irq %d request for gpio=%d ret=%d\n",
+ gpio_to_irq(kona_dev->cfg->cd_gpio),
+ kona_dev->cfg->cd_gpio, ret);
+ goto err_remove_host;
+ }
+ if (gpio_is_valid(kona_dev->cfg->wp_gpio)) {
+ ret = devm_gpio_request(dev,
+ kona_dev->cfg->wp_gpio, "sdio wp");
+ if (ret < 0) {
+ dev_err(&pdev->dev,
+ "Unable to request WP pin %d\n",
+ kona_dev->cfg->wp_gpio);
+ kona_dev->cfg->wp_gpio = -1;
+ } else {
+ gpio_direction_input(kona_dev->cfg->wp_gpio);
+ }
+ }
+
+ /*
+ * Since the card detection GPIO interrupt is configured to be
+ * edge sensitive, check the initial GPIO value here, emulate
+ * only if the card is present
+ */
+ if (gpio_get_value_cansleep(kona_dev->cfg->cd_gpio) == 0)
+ sdhci_bcm_kona_sd_card_emulate(host, 1);
+ }
+
+ dev_dbg(dev, "initialized properly\n");
+ return 0;
+
+err_remove_host:
+ sdhci_remove_host(host, 0);
+
+err_reset:
+ sdhci_bcm_kona_sd_reset(host);
+
+err_pltfm_free:
+ sdhci_pltfm_free(pdev);
+
+ dev_err(dev, "Probing of sdhci-pltfm failed: %d\n", ret);
+ return ret;
+}
+
+static int __exit sdhci_bcm_kona_remove(struct platform_device *pdev)
+{
+ struct sdhci_host *host = platform_get_drvdata(pdev);
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_bcm_kona_dev *kona_dev = pltfm_host->priv;
+ int dead;
+ u32 scratch;
+
+ dead = 0;
+ scratch = readl(host->ioaddr + SDHCI_INT_STATUS);
+ if (scratch == (u32)-1)
+ dead = 1;
+ sdhci_remove_host(host, dead);
+
+ sdhci_free_host(host);
+
+ return 0;
+}
+
+static struct platform_driver sdhci_bcm_kona_driver = {
+ .driver = {
+ .name = "sdhci-kona",
+ .owner = THIS_MODULE,
+ .pm = SDHCI_PLTFM_PMOPS,
+ .of_match_table = of_match_ptr(sdhci_bcm_kona_of_match),
+ },
+ .probe = sdhci_bcm_kona_probe,
+ .remove = __exit_p(sdhci_bcm_kona_remove),
+};
+module_platform_driver(sdhci_bcm_kona_driver);
+
+MODULE_DESCRIPTION("SDHCI driver for Broadcom Kona platform");
+MODULE_AUTHOR("Broadcom");
+MODULE_LICENSE("GPL v2");
+
Add SDHCI driver for the Broadcom 281xx SoCs. Also add bindings for it into bcm281xx dts files. Still missing: - power managemement Changes from V1: - split DT into separate patch - use gpio_is_valid instead of direct test - switch pr_debug calls to dev_dbg - use of_property_read_bool Signed-off-by: Christian Daudt <csd@broadcom.com>