| Message ID | 1370013591-25957-1-git-send-email-dmurphy@ti.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
Hello Dan, On 05/31/2013 05:19 PM, Dan Murphy wrote: > The GPIO for LED D1 on the omap4-panda a1-a3 rev and the omap4-panda-es > are different. > > A1-A3 = gpio_wk7 > ES = gpio_110 > > There is no change to LED D2 > > Abstract away the pinmux and the LED definitions for the two boards into > the respective DTS files. > > Signed-off-by: Dan Murphy <dmurphy@ti.com> > --- > v9 - Removed comments for mux config - https://patchwork.kernel.org/patch/2644391/ > v8 - Rebase to latest and use pinctrl macros - https://patchwork.kernel.org/patch/2629351/ > v7 - Update headline to add spaces - https://patchwork.kernel.org/patch/2583661/ > v6 - Review comments updated - https://patchwork.kernel.org/patch/2582771/ > v5 - Provide pincrtl phandle to the gpio-led driver - https://patchwork.kernel.org/patch/2573981/ > arch/arm/boot/dts/omap4-panda-common.dtsi | 16 +++++++++++++++- > arch/arm/boot/dts/omap4-panda-es.dts | 28 ++++++++++++++++++++++++++++ > 2 files changed, 43 insertions(+), 1 deletions(-) > > diff --git a/arch/arm/boot/dts/omap4-panda-common.dtsi b/arch/arm/boot/dts/omap4-panda-common.dtsi > index d5d144a..800fa4e 100644 > --- a/arch/arm/boot/dts/omap4-panda-common.dtsi > +++ b/arch/arm/boot/dts/omap4-panda-common.dtsi > @@ -16,8 +16,13 @@ > reg = <0x80000000 0x40000000>; /* 1 GB */ > }; > > - leds { > + leds: leds { > compatible = "gpio-leds"; > + pinctrl-names = "default"; > + pinctrl-0 = < > + &led_wkgpio_pins > + >; > + > heartbeat { > label = "pandaboard::status1"; > gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>; > @@ -157,6 +162,15 @@ > }; > }; > > +&omap4_pmx_wkup { > + led_wkgpio_pins: pinmux_leds_wkpins { > + pinctrl-single,pins = < > + 0x1a (PIN_OUTPUT | MUX_MODE3) /* gpio_wk7 */ > + 0x1c (PIN_OUTPUT | MUX_MODE3) /* gpio_wk8 */ > + >; > + }; > +}; > + > &i2c1 { > pinctrl-names = "default"; > pinctrl-0 = <&i2c1_pins>; > diff --git a/arch/arm/boot/dts/omap4-panda-es.dts b/arch/arm/boot/dts/omap4-panda-es.dts > index 5cfdf19..0a7812f 100644 > --- a/arch/arm/boot/dts/omap4-panda-es.dts > +++ b/arch/arm/boot/dts/omap4-panda-es.dts > @@ -34,3 +34,31 @@ > 0x5e (PIN_INPUT | MUX_MODE0) /* hdmi_sda.hdmi_sda */ > >; > }; > + > +&omap4_pmx_core { > + led_gpio_pins: gpio_led_pmx { > + pinctrl-single,pins = < > + 0xb6 (PIN_OUTPUT | MUX_MODE3) /* gpio_110 */ > + >; > + }; > +}; > + > +&led_wkgpio_pins { > + pinctrl-single,pins = < > + 0x1c (PIN_OUTPUT | MUX_MODE3) /* gpio_wk8 */ > + >; > +}; > + > +&leds { > + pinctrl-0 = < > + &led_gpio_pins > + &led_wkgpio_pins > + >; > + > + heartbeat { > + gpios = <&gpio4 14 0>; And here you could use the GPIO defines: gpios = <&gpio4 14 GPIO_ACTIVE_HIGH>; > + }; > + mmc { > + gpios = <&gpio1 8 0>; Same here. > + }; > +}; > Regards, Florian
diff --git a/arch/arm/boot/dts/omap4-panda-common.dtsi b/arch/arm/boot/dts/omap4-panda-common.dtsi index d5d144a..800fa4e 100644 --- a/arch/arm/boot/dts/omap4-panda-common.dtsi +++ b/arch/arm/boot/dts/omap4-panda-common.dtsi @@ -16,8 +16,13 @@ reg = <0x80000000 0x40000000>; /* 1 GB */ }; - leds { + leds: leds { compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = < + &led_wkgpio_pins + >; + heartbeat { label = "pandaboard::status1"; gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>; @@ -157,6 +162,15 @@ }; }; +&omap4_pmx_wkup { + led_wkgpio_pins: pinmux_leds_wkpins { + pinctrl-single,pins = < + 0x1a (PIN_OUTPUT | MUX_MODE3) /* gpio_wk7 */ + 0x1c (PIN_OUTPUT | MUX_MODE3) /* gpio_wk8 */ + >; + }; +}; + &i2c1 { pinctrl-names = "default"; pinctrl-0 = <&i2c1_pins>; diff --git a/arch/arm/boot/dts/omap4-panda-es.dts b/arch/arm/boot/dts/omap4-panda-es.dts index 5cfdf19..0a7812f 100644 --- a/arch/arm/boot/dts/omap4-panda-es.dts +++ b/arch/arm/boot/dts/omap4-panda-es.dts @@ -34,3 +34,31 @@ 0x5e (PIN_INPUT | MUX_MODE0) /* hdmi_sda.hdmi_sda */ >; }; + +&omap4_pmx_core { + led_gpio_pins: gpio_led_pmx { + pinctrl-single,pins = < + 0xb6 (PIN_OUTPUT | MUX_MODE3) /* gpio_110 */ + >; + }; +}; + +&led_wkgpio_pins { + pinctrl-single,pins = < + 0x1c (PIN_OUTPUT | MUX_MODE3) /* gpio_wk8 */ + >; +}; + +&leds { + pinctrl-0 = < + &led_gpio_pins + &led_wkgpio_pins + >; + + heartbeat { + gpios = <&gpio4 14 0>; + }; + mmc { + gpios = <&gpio1 8 0>; + }; +};
The GPIO for LED D1 on the omap4-panda a1-a3 rev and the omap4-panda-es are different. A1-A3 = gpio_wk7 ES = gpio_110 There is no change to LED D2 Abstract away the pinmux and the LED definitions for the two boards into the respective DTS files. Signed-off-by: Dan Murphy <dmurphy@ti.com> --- v9 - Removed comments for mux config - https://patchwork.kernel.org/patch/2644391/ v8 - Rebase to latest and use pinctrl macros - https://patchwork.kernel.org/patch/2629351/ v7 - Update headline to add spaces - https://patchwork.kernel.org/patch/2583661/ v6 - Review comments updated - https://patchwork.kernel.org/patch/2582771/ v5 - Provide pincrtl phandle to the gpio-led driver - https://patchwork.kernel.org/patch/2573981/ arch/arm/boot/dts/omap4-panda-common.dtsi | 16 +++++++++++++++- arch/arm/boot/dts/omap4-panda-es.dts | 28 ++++++++++++++++++++++++++++ 2 files changed, 43 insertions(+), 1 deletions(-)