@@ -43,6 +43,10 @@ Required properties:
together. This would still allow different sample sizes,
but not different sample rates.
+Required are also ac97 link bindings if ac97 is used. See
+Documentation/devicetree/bindings/sound/soc-ac97link.txt for the necessary
+bindings.
+
Optional properties:
- codec-handle: Phandle to a 'codec' node that defines an audio
codec connected to this SSI. This node is typically
@@ -141,6 +141,7 @@ struct fsl_ssi_private {
bool new_binding;
bool ssi_on_imx;
+ bool imx_ac97;
bool use_dma;
struct clk *clk;
struct snd_dmaengine_dai_dma_data dma_params_tx;
@@ -320,6 +321,124 @@ static irqreturn_t fsl_ssi_isr(int irq, void *dev_id)
return ret;
}
+static int fsl_ssi_setup(struct fsl_ssi_private *ssi_private)
+{
+ struct ccsr_ssi __iomem *ssi = ssi_private->ssi;
+ u8 i2s_mode;
+ u8 wm;
+ int synchronous = ssi_private->cpu_dai_drv.symmetric_rates;
+
+ if (ssi_private->imx_ac97)
+ i2s_mode = CCSR_SSI_SCR_I2S_MODE_NORMAL | CCSR_SSI_SCR_NET;
+ else
+ i2s_mode = CCSR_SSI_SCR_I2S_MODE_SLAVE;
+
+ /*
+ * Section 16.5 of the MPC8610 reference manual says that the SSI needs
+ * to be disabled before updating the registers we set here.
+ */
+ write_ssi_mask(&ssi->scr, CCSR_SSI_SCR_SSIEN, 0);
+
+ /*
+ * Program the SSI into I2S Slave Non-Network Synchronous mode. Also
+ * enable the transmit and receive FIFO.
+ *
+ * FIXME: Little-endian samples require a different shift dir
+ */
+ write_ssi_mask(&ssi->scr,
+ CCSR_SSI_SCR_I2S_MODE_MASK | CCSR_SSI_SCR_SYN,
+ CCSR_SSI_SCR_TFR_CLK_DIS |
+ i2s_mode |
+ (synchronous ? CCSR_SSI_SCR_SYN : 0));
+
+ write_ssi(CCSR_SSI_STCR_TXBIT0 | CCSR_SSI_STCR_TFEN0 |
+ CCSR_SSI_STCR_TFSI | CCSR_SSI_STCR_TEFS |
+ CCSR_SSI_STCR_TSCKP, &ssi->stcr);
+
+ write_ssi(CCSR_SSI_SRCR_RXBIT0 | CCSR_SSI_SRCR_RFEN0 |
+ CCSR_SSI_SRCR_RFSI | CCSR_SSI_SRCR_REFS |
+ CCSR_SSI_SRCR_RSCKP, &ssi->srcr);
+ /*
+ * The DC and PM bits are only used if the SSI is the clock master.
+ */
+
+ /*
+ * Set the watermark for transmit FIFI 0 and receive FIFO 0. We don't
+ * use FIFO 1. We program the transmit water to signal a DMA transfer
+ * if there are only two (or fewer) elements left in the FIFO. Two
+ * elements equals one frame (left channel, right channel). This value,
+ * however, depends on the depth of the transmit buffer.
+ *
+ * We set the watermark on the same level as the DMA burstsize. For
+ * fiq it is probably better to use the biggest possible watermark
+ * size.
+ */
+ if (ssi_private->use_dma)
+ wm = ssi_private->fifo_depth - 2;
+ else
+ wm = ssi_private->fifo_depth;
+
+ write_ssi(CCSR_SSI_SFCSR_TFWM0(wm) | CCSR_SSI_SFCSR_RFWM0(wm) |
+ CCSR_SSI_SFCSR_TFWM1(wm) | CCSR_SSI_SFCSR_RFWM1(wm),
+ &ssi->sfcsr);
+
+ /*
+ * For non-ac97 setups, we keep the SSI disabled because if we enable
+ * it, then the DMA controller will start. It's not supposed to start
+ * until the SCR.TE (or SCR.RE) bit is set, but it does anyway. The DMA
+ * controller will transfer one "BWC" of data (i.e. the amount of data
+ * that the MR.BWC bits are set to). The reason this is bad is because
+ * at this point, the PCM driver has not finished initializing the DMA
+ * controller.
+ */
+
+
+ /*
+ * For ac97 interrupts are enabled with the startup of the substream
+ * because it is also running without an active substream. Normally SSI
+ * is only enabled when there is a substream.
+ */
+ if (!ssi_private->imx_ac97) {
+ /* Enable the interrupts and DMA requests */
+ if (ssi_private->use_dma)
+ write_ssi(SIER_FLAGS, &ssi->sier);
+ else
+ write_ssi(CCSR_SSI_SIER_TIE | CCSR_SSI_SIER_TFE0_EN |
+ CCSR_SSI_SIER_RIE |
+ CCSR_SSI_SIER_RFF0_EN, &ssi->sier);
+ } else {
+ /*
+ * Setup the clock control register
+ */
+ write_ssi(CCSR_SSI_SxCCR_WL(17) | CCSR_SSI_SxCCR_DC(13),
+ &ssi->stccr);
+ write_ssi(CCSR_SSI_SxCCR_WL(17) | CCSR_SSI_SxCCR_DC(13),
+ &ssi->srccr);
+
+ /*
+ * Enable AC97 mode and startup the SSI
+ */
+ write_ssi(CCSR_SSI_SACNT_AC97EN | CCSR_SSI_SACNT_FV,
+ &ssi->sacnt);
+ write_ssi(0xff, &ssi->saccdis);
+ write_ssi(0x300, &ssi->saccen);
+
+ /*
+ * Enable SSI
+ */
+ write_ssi_mask(&ssi->scr, 0, CCSR_SSI_SCR_SSIEN);
+ write_ssi(CCSR_SSI_SOR_WAIT(3), &ssi->sor);
+
+ /*
+ * Enable Transmit and Receive
+ */
+ write_ssi_mask(&ssi->scr, 0, CCSR_SSI_SCR_TE | CCSR_SSI_SCR_RE);
+ }
+
+ return 0;
+}
+
+
/**
* fsl_ssi_startup: create a new substream
*
@@ -341,75 +460,14 @@ static int fsl_ssi_startup(struct snd_pcm_substream *substream,
* and initialize the SSI registers.
*/
if (!ssi_private->first_stream) {
- struct ccsr_ssi __iomem *ssi = ssi_private->ssi;
-
ssi_private->first_stream = substream;
/*
- * Section 16.5 of the MPC8610 reference manual says that the
- * SSI needs to be disabled before updating the registers we set
- * here.
- */
- write_ssi_mask(&ssi->scr, CCSR_SSI_SCR_SSIEN, 0);
-
- /*
- * Program the SSI into I2S Slave Non-Network Synchronous mode.
- * Also enable the transmit and receive FIFO.
- *
- * FIXME: Little-endian samples require a different shift dir
- */
- write_ssi_mask(&ssi->scr,
- CCSR_SSI_SCR_I2S_MODE_MASK | CCSR_SSI_SCR_SYN,
- CCSR_SSI_SCR_TFR_CLK_DIS | CCSR_SSI_SCR_I2S_MODE_SLAVE
- | (synchronous ? CCSR_SSI_SCR_SYN : 0));
-
- write_ssi(CCSR_SSI_STCR_TXBIT0 | CCSR_SSI_STCR_TFEN0 |
- CCSR_SSI_STCR_TFSI | CCSR_SSI_STCR_TEFS |
- CCSR_SSI_STCR_TSCKP, &ssi->stcr);
-
- write_ssi(CCSR_SSI_SRCR_RXBIT0 | CCSR_SSI_SRCR_RFEN0 |
- CCSR_SSI_SRCR_RFSI | CCSR_SSI_SRCR_REFS |
- CCSR_SSI_SRCR_RSCKP, &ssi->srcr);
-
- /*
- * The DC and PM bits are only used if the SSI is the clock
- * master.
- */
-
- /* Enable the interrupts and DMA requests */
- if (ssi_private->use_dma)
- write_ssi(SIER_FLAGS, &ssi->sier);
- else
- write_ssi(CCSR_SSI_SIER_TIE | CCSR_SSI_SIER_TFE0_EN |
- CCSR_SSI_SIER_RIE |
- CCSR_SSI_SIER_RFF0_EN, &ssi->sier);
-
- /*
- * Set the watermark for transmit FIFI 0 and receive FIFO 0. We
- * don't use FIFO 1. We program the transmit water to signal a
- * DMA transfer if there are only two (or fewer) elements left
- * in the FIFO. Two elements equals one frame (left channel,
- * right channel). This value, however, depends on the depth of
- * the transmit buffer.
- *
- * We program the receive FIFO to notify us if at least two
- * elements (one frame) have been written to the FIFO. We could
- * make this value larger (and maybe we should), but this way
- * data will be written to memory as soon as it's available.
- */
- write_ssi(CCSR_SSI_SFCSR_TFWM0(ssi_private->fifo_depth - 2) |
- CCSR_SSI_SFCSR_RFWM0(ssi_private->fifo_depth - 2),
- &ssi->sfcsr);
-
- /*
- * We keep the SSI disabled because if we enable it, then the
- * DMA controller will start. It's not supposed to start until
- * the SCR.TE (or SCR.RE) bit is set, but it does anyway. The
- * DMA controller will transfer one "BWC" of data (i.e. the
- * amount of data that the MR.BWC bits are set to). The reason
- * this is bad is because at this point, the PCM driver has not
- * finished initializing the DMA controller.
+ * fsl_ssi_setup was already called by ac97_init earlier if
+ * the driver is in ac97 mode.
*/
+ if (!ssi_private->imx_ac97)
+ fsl_ssi_setup(ssi_private);
} else {
if (synchronous) {
struct snd_pcm_runtime *first_runtime =
@@ -538,7 +596,8 @@ static int fsl_ssi_trigger(struct snd_pcm_substream *substream, int cmd,
else
write_ssi_mask(&ssi->scr, CCSR_SSI_SCR_RE, 0);
- if ((read_ssi(&ssi->scr) & (CCSR_SSI_SCR_TE | CCSR_SSI_SCR_RE)) == 0)
+ if (!ssi_private->imx_ac97 && (read_ssi(&ssi->scr) &
+ (CCSR_SSI_SCR_TE | CCSR_SSI_SCR_RE)) == 0)
write_ssi_mask(&ssi->scr, CCSR_SSI_SCR_SSIEN, 0);
break;
@@ -608,6 +667,133 @@ static const struct snd_soc_component_driver fsl_ssi_component = {
.name = "fsl-ssi",
};
+/**
+ * fsl_ssi_ac97_trigger: start and stop the AC97 receive/transmit.
+ *
+ * This function is called by ALSA to start, stop, pause, and resume the
+ * transfer of data.
+ */
+static int fsl_ssi_ac97_trigger(struct snd_pcm_substream *substream, int cmd,
+ struct snd_soc_dai *dai)
+{
+ struct snd_soc_pcm_runtime *rtd = substream->private_data;
+ struct fsl_ssi_private *ssi_private = snd_soc_dai_get_drvdata(
+ rtd->cpu_dai);
+ struct ccsr_ssi __iomem *ssi = ssi_private->ssi;
+
+ switch (cmd) {
+ case SNDRV_PCM_TRIGGER_START:
+ case SNDRV_PCM_TRIGGER_PAUSE_RELEASE:
+ if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK)
+ write_ssi_mask(&ssi->sier, 0, CCSR_SSI_SIER_TIE |
+ CCSR_SSI_SIER_TFE0_EN);
+ else
+ write_ssi_mask(&ssi->sier, 0, CCSR_SSI_SIER_RIE |
+ CCSR_SSI_SIER_RFF0_EN);
+ break;
+
+ case SNDRV_PCM_TRIGGER_STOP:
+ case SNDRV_PCM_TRIGGER_PAUSE_PUSH:
+ if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK)
+ write_ssi_mask(&ssi->sier, CCSR_SSI_SIER_TIE |
+ CCSR_SSI_SIER_TFE0_EN, 0);
+ else
+ write_ssi_mask(&ssi->sier, CCSR_SSI_SIER_RIE |
+ CCSR_SSI_SIER_RFF0_EN, 0);
+ break;
+
+ default:
+ return -EINVAL;
+ }
+
+ if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK)
+ write_ssi(CCSR_SSI_SOR_TX_CLR, &ssi->sor);
+ else
+ write_ssi(CCSR_SSI_SOR_RX_CLR, &ssi->sor);
+
+ return 0;
+}
+
+static const struct snd_soc_dai_ops fsl_ssi_ac97_dai_ops = {
+ .startup = fsl_ssi_startup,
+ .shutdown = fsl_ssi_shutdown,
+ .trigger = fsl_ssi_ac97_trigger,
+};
+
+static struct snd_soc_dai_driver fsl_ssi_ac97_dai = {
+ .ac97_control = 1,
+ .playback = {
+ .stream_name = "AC97 Playback",
+ .channels_min = 2,
+ .channels_max = 2,
+ .rates = SNDRV_PCM_RATE_8000_48000,
+ .formats = SNDRV_PCM_FMTBIT_S16_LE,
+ },
+ .capture = {
+ .stream_name = "AC97 Capture",
+ .channels_min = 2,
+ .channels_max = 2,
+ .rates = SNDRV_PCM_RATE_48000,
+ .formats = SNDRV_PCM_FMTBIT_S16_LE,
+ },
+ .ops = &fsl_ssi_ac97_dai_ops,
+};
+
+
+static struct fsl_ssi_private *fsl_ac97_data;
+
+static void fsl_ssi_ac97_init(void)
+{
+ fsl_ssi_setup(fsl_ac97_data);
+}
+
+void fsl_ssi_ac97_write(struct snd_ac97 *ac97, unsigned short reg,
+ unsigned short val)
+{
+ struct ccsr_ssi *ssi = fsl_ac97_data->ssi;
+ unsigned int lreg;
+ unsigned int lval;
+
+ if (reg > 0x7f)
+ return;
+
+
+ lreg = reg << 12;
+ write_ssi(lreg, &ssi->sacadd);
+
+ lval = val << 4;
+ write_ssi(lval , &ssi->sacdat);
+
+ write_ssi_mask(&ssi->sacnt, CCSR_SSI_SACNT_RDWR_MASK,
+ CCSR_SSI_SACNT_WR);
+ udelay(100);
+}
+
+unsigned short fsl_ssi_ac97_read(struct snd_ac97 *ac97,
+ unsigned short reg)
+{
+ struct ccsr_ssi *ssi = fsl_ac97_data->ssi;
+
+ unsigned short val = -1;
+ unsigned int lreg;
+
+ lreg = (reg & 0x7f) << 12;
+ write_ssi(lreg, &ssi->sacadd);
+ write_ssi_mask(&ssi->sacnt, CCSR_SSI_SACNT_RDWR_MASK,
+ CCSR_SSI_SACNT_RD);
+
+ udelay(100);
+
+ val = (read_ssi(&ssi->sacdat) >> 4) & 0xffff;
+
+ return val;
+}
+
+static struct snd_ac97_bus_ops fsl_ssi_ac97_ops = {
+ .read = fsl_ssi_ac97_read,
+ .write = fsl_ssi_ac97_write,
+};
+
/* Show the statistics of a flag only if its interrupt is enabled. The
* compiler will optimze this code to a no-op if the interrupt is not
* enabled.
@@ -684,6 +870,7 @@ static int fsl_ssi_probe(struct platform_device *pdev)
struct resource res;
char name[64];
bool shared;
+ bool ac97 = false;
/* SSIs that are not connected on the board should have a
* status = "disabled"
@@ -694,7 +881,13 @@ static int fsl_ssi_probe(struct platform_device *pdev)
/* We only support the SSI in "I2S Slave" mode */
sprop = of_get_property(np, "fsl,mode", NULL);
- if (!sprop || strcmp(sprop, "i2s-slave")) {
+ if (!sprop) {
+ dev_err(&pdev->dev, "fsl,mode property is necessary\n");
+ return -EINVAL;
+ }
+ if (!strcmp(sprop, "ac97-slave")) {
+ ac97 = true;
+ } else if (strcmp(sprop, "i2s-slave")) {
dev_notice(&pdev->dev, "mode %s is unsupported\n", sprop);
return -ENODEV;
}
@@ -713,9 +906,19 @@ static int fsl_ssi_probe(struct platform_device *pdev)
ssi_private->use_dma = !of_property_read_bool(np,
"fsl,fiq-stream-filter");
- /* Initialize this copy of the CPU DAI driver structure */
- memcpy(&ssi_private->cpu_dai_drv, &fsl_ssi_dai_template,
- sizeof(fsl_ssi_dai_template));
+ if (ac97) {
+ memcpy(&ssi_private->cpu_dai_drv, &fsl_ssi_ac97_dai,
+ sizeof(fsl_ssi_ac97_dai));
+
+ fsl_ac97_data = ssi_private;
+ ssi_private->imx_ac97 = true;
+
+ snd_soc_set_ac97_ops_of_reset(&fsl_ssi_ac97_ops, pdev);
+ } else {
+ /* Initialize this copy of the CPU DAI driver structure */
+ memcpy(&ssi_private->cpu_dai_drv, &fsl_ssi_dai_template,
+ sizeof(fsl_ssi_dai_template));
+ }
ssi_private->cpu_dai_drv.name = ssi_private->name;
/* Get the addresses and IRQ */
@@ -901,6 +1104,9 @@ static int fsl_ssi_probe(struct platform_device *pdev)
}
done:
+ if (ssi_private->imx_ac97)
+ fsl_ssi_ac97_init();
+
return 0;
error_dai: