@@ -8,6 +8,7 @@ dtb-$(CONFIG_ARCH_AT91) += at91-carmeva.dtb
dtb-$(CONFIG_ARCH_AT91) += at91-ecbat91.dtb
dtb-$(CONFIG_ARCH_AT91) += at91-flexibity.dtb
dtb-$(CONFIG_ARCH_AT91) += at91-kafa.dtb
+dtb-$(CONFIG_ARCH_AT91) += at91-kb9202.dtb
dtb-$(CONFIG_ARCH_AT91) += at91-picotux-200.dtb
dtb-$(CONFIG_ARCH_AT91) += at91-rsi-ews.dtb
dtb-$(CONFIG_ARCH_AT91) += mpa1600.dtb
new file mode 100644
@@ -0,0 +1,135 @@
+/*
+ * at91-kb9202.dtb - Device Tree file for RSI EWS board
+ *
+ * Copyright (C) 2013 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+ *
+ * Licensed under GPLv2 only
+ */
+/dts-v1/;
+#include "at91rm9200_pqfp.dtsi"
+
+/ {
+ model = "KB920x";
+ compatible = "kwikbyte,kb920x", "atmel,at91rm9200-pqfp", "atmel,at91rm9200";
+
+ aliases {
+ serial0 = &dbgu;
+ serial1 = &usart0;
+ serial2 = &usart1;
+ serial3 = &usart3;
+ serial4 = &usart2;
+ };
+
+ clocks {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ main_clock: clock@0 {
+ compatible = "atmel,osc", "fixed-clock";
+ clock-frequency = <10000000>;
+ };
+ };
+
+ ahb {
+ apb {
+ dbgu: serial@fffff200 {
+ status = "okay";
+ };
+
+ usart0: serial@fffc0000 {
+ status = "okay";
+ };
+
+ usart1: serial@fffc4000 {
+ status = "okay";
+ };
+
+ usart3: serial@fffcc000 {
+ pinctrl-0 =
+ <&pinctrl_uart3
+ &pinctrl_uart3_cts
+ &pinctrl_uart3_rts>;
+ status = "okay";
+ };
+
+ macb0: ethernet@fffbc000 {
+ phy-mode = "mii";
+ status = "okay";
+ /* phy irq on PB29 */
+ pinctrl-0 = <&pinctrl_macb_rmii &pinctrl_macb_rmii_mii>;
+ };
+
+ mmc0: mmc@fffb4000 {
+ pinctrl-0 = <
+ &pinctrl_board_mmc0
+ &pinctrl_mmc0_clk
+ &pinctrl_mmc0_slot0_cmd_dat0
+ &pinctrl_mmc0_slot0_dat1_3>;
+ status = "okay";
+ slot@0 {
+ reg = <0>;
+ bus-width = <4>;
+ cd-gpios = <&pioB 2 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ pinctrl@fffff400 {
+ mmc0 {
+ pinctrl_board_mmc0: mmc0-board {
+ atmel,pins =
+ <AT91_PIOB 2 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;
+ };
+ };
+ };
+
+ spi0: spi@fffe0000 {
+ status = "okay";
+ };
+
+ usb1: gadget@fffb0000 {
+ status = "okay";
+ atmel,vbus-gpio = <&pioB 24 GPIO_ACTIVE_HIGH>;
+ atmel,pullup-gpio = <&pioB 22 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ usb0: ohci@00300000 {
+ num-ports = <1>;
+ status = "okay";
+ };
+
+ nand0: nand@40000000 {
+ status = "okay";
+ gpios = <&pioC 29 GPIO_ACTIVE_HIGH /* rdy */
+ &pioD 28 GPIO_ACTIVE_HIGH /* nce */
+ 0 /* cd */
+ >;
+
+ nand_fs@0 {
+ label = "nand_fs";
+ reg = <0x00000 0x10000000>;
+ };
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led0 {
+ label = "led0";
+ gpios = <&pioC 19 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "heartbeat";
+ };
+
+ led1 {
+ label = "led1";
+ gpios = <&pioC 18 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "timer";
+ };
+ };
+
+ i2c@0 {
+ status = "okay";
+ };
+};
@@ -21,7 +21,6 @@ CONFIG_MACH_AT91RM9200EK=y
CONFIG_MACH_CSB337=y
CONFIG_MACH_CSB637=y
CONFIG_MACH_ATEB9200=y
-CONFIG_MACH_KB9200=y
CONFIG_MACH_YL9200=y
CONFIG_MACH_CPUAT91=y
CONFIG_MACH_ECO920=y
@@ -81,12 +81,6 @@ config MACH_ATEB9200
Select this if you are using Embest's ATEB9200 board.
<http://www.embedinfo.com/english/product/ATEB9200.asp>
-config MACH_KB9200
- bool "KwikByte KB920x"
- help
- Select this if you are using KwikByte's KB920x board.
- <http://www.kwikbyte.com/KB9202.html>
-
config MACH_YL9200
bool "ucDragon YL-9200"
help
@@ -36,7 +36,6 @@ obj-$(CONFIG_ARCH_AT91X40) += at91x40.o at91x40_time.o
obj-$(CONFIG_MACH_AT91RM9200EK) += board-rm9200ek.o
obj-$(CONFIG_MACH_CSB337) += board-csb337.o
obj-$(CONFIG_MACH_CSB637) += board-csb637.o
-obj-$(CONFIG_MACH_KB9200) += board-kb9202.o
obj-$(CONFIG_MACH_ATEB9200) += board-eb9200.o
obj-$(CONFIG_MACH_YL9200) += board-yl-9200.o
obj-$(CONFIG_MACH_CPUAT91) += board-cpuat91.o
deleted file mode 100644
@@ -1,158 +0,0 @@
-/*
- * linux/arch/arm/mach-at91/board-kb9202.c
- *
- * Copyright (c) 2005 kb_admin
- * KwikByte, Inc.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- */
-
-#include <linux/types.h>
-#include <linux/gpio.h>
-#include <linux/init.h>
-#include <linux/mm.h>
-#include <linux/module.h>
-#include <linux/platform_device.h>
-
-#include <mach/hardware.h>
-#include <asm/setup.h>
-#include <asm/mach-types.h>
-#include <asm/irq.h>
-
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/irq.h>
-
-#include <mach/cpu.h>
-#include <mach/at91rm9200_mc.h>
-#include <mach/at91_ramc.h>
-
-#include "at91_aic.h"
-#include "board.h"
-#include "generic.h"
-
-
-static void __init kb9202_init_early(void)
-{
- /* Set cpu type: PQFP */
- at91rm9200_set_type(ARCH_REVISON_9200_PQFP);
-
- /* Initialize processor: 10 MHz crystal */
- at91_initialize(10000000);
-}
-
-static struct macb_platform_data __initdata kb9202_eth_data = {
- .phy_irq_pin = AT91_PIN_PB29,
- .is_rmii = 0,
-};
-
-static struct at91_usbh_data __initdata kb9202_usbh_data = {
- .ports = 1,
- .vbus_pin = {-EINVAL, -EINVAL},
- .overcurrent_pin= {-EINVAL, -EINVAL},
-};
-
-static struct at91_udc_data __initdata kb9202_udc_data = {
- .vbus_pin = AT91_PIN_PB24,
- .pullup_pin = AT91_PIN_PB22,
-};
-
-static struct mci_platform_data __initdata kb9202_mci0_data = {
- .slot[0] = {
- .bus_width = 4,
- .detect_pin = AT91_PIN_PB2,
- .wp_pin = -EINVAL,
- },
-};
-
-static struct mtd_partition __initdata kb9202_nand_partition[] = {
- {
- .name = "nand_fs",
- .offset = 0,
- .size = MTDPART_SIZ_FULL,
- },
-};
-
-static struct atmel_nand_data __initdata kb9202_nand_data = {
- .ale = 22,
- .cle = 21,
- .det_pin = -EINVAL,
- .rdy_pin = AT91_PIN_PC29,
- .enable_pin = AT91_PIN_PC28,
- .ecc_mode = NAND_ECC_SOFT,
- .parts = kb9202_nand_partition,
- .num_parts = ARRAY_SIZE(kb9202_nand_partition),
-};
-
-/*
- * LEDs
- */
-static struct gpio_led kb9202_leds[] = {
- { /* D1 */
- .name = "led1",
- .gpio = AT91_PIN_PC19,
- .active_low = 1,
- .default_trigger = "heartbeat",
- },
- { /* D2 */
- .name = "led2",
- .gpio = AT91_PIN_PC18,
- .active_low = 1,
- .default_trigger = "timer",
- }
-};
-
-static void __init kb9202_board_init(void)
-{
- /* Serial */
- /* DBGU on ttyS0. (Rx & Tx only) */
- at91_register_uart(0, 0, 0);
-
- /* USART0 on ttyS1 (Rx & Tx only) */
- at91_register_uart(AT91RM9200_ID_US0, 1, 0);
-
- /* USART1 on ttyS2 (Rx & Tx only) - IRDA (optional) */
- at91_register_uart(AT91RM9200_ID_US1, 2, 0);
-
- /* USART3 on ttyS3 (Rx, Tx, CTS, RTS) - RS485 (optional) */
- at91_register_uart(AT91RM9200_ID_US3, 3, ATMEL_UART_CTS | ATMEL_UART_RTS);
- at91_add_device_serial();
- /* Ethernet */
- at91_add_device_eth(&kb9202_eth_data);
- /* USB Host */
- at91_add_device_usbh(&kb9202_usbh_data);
- /* USB Device */
- at91_add_device_udc(&kb9202_udc_data);
- /* MMC */
- at91_add_device_mci(0, &kb9202_mci0_data);
- /* I2C */
- at91_add_device_i2c(NULL, 0);
- /* SPI */
- at91_add_device_spi(NULL, 0);
- /* NAND */
- at91_add_device_nand(&kb9202_nand_data);
- /* LEDs */
- at91_gpio_leds(kb9202_leds, ARRAY_SIZE(kb9202_leds));
-}
-
-MACHINE_START(KB9200, "KB920x")
- /* Maintainer: KwikByte, Inc. */
- .init_time = at91rm9200_timer_init,
- .map_io = at91_map_io,
- .handle_irq = at91_aic_handle_irq,
- .init_early = kb9202_init_early,
- .init_irq = at91_init_irq_default,
- .init_machine = kb9202_board_init,
-MACHINE_END
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Cc: Nicolas Ferre <nicolas.ferre@atmel.com> --- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/at91-kb9202.dts | 135 +++++++++++++++++++++++++++++ arch/arm/configs/at91rm9200_defconfig | 1 - arch/arm/mach-at91/Kconfig.non_dt | 6 -- arch/arm/mach-at91/Makefile | 1 - arch/arm/mach-at91/board-kb9202.c | 158 ---------------------------------- 6 files changed, 136 insertions(+), 166 deletions(-) create mode 100644 arch/arm/boot/dts/at91-kb9202.dts delete mode 100644 arch/arm/mach-at91/board-kb9202.c