@@ -178,6 +178,8 @@ dtb-$(CONFIG_ARCH_MXS) += imx23-evk.dtb \
imx28-cfa10057.dtb \
imx28-cfa10058.dtb \
imx28-duckbill.dtb \
+ imx28-eukrea-mbmx283lc.dtb \
+ imx28-eukrea-mbmx287lc.dtb \
imx28-evk.dtb \
imx28-m28cu3.dtb \
imx28-m28evk.dtb \
new file mode 100644
@@ -0,0 +1,71 @@
+/*
+ * Copyright 2013 Eukréa Electromatique <eric@eukrea.com>
+ * Copyright 2013 Eukréa Electromatique <denis@eukrea.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version 2
+ * of the License, or (at your option) any later version.
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+/*
+ * Module contains : i.MX282 + 64MB DDR2 + NAND + Ethernet PHY + RTC
+ */
+
+/dts-v1/;
+#include "imx28-eukrea-mbmx28lc.dtsi"
+
+/ {
+ model = "Eukrea Electromatique MBMX283LC";
+ compatible = "eukrea,mbmx283lc", "eukrea,mbmx28lc", "fsl,imx28";
+
+ memory {
+ reg = <0x40000000 0x04000000>;
+ };
+};
+
+&gpmi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpmi_pins_a>;
+ status = "okay";
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+
+ pcf8563: rtc@51 {
+ compatible = "nxp,pcf8563";
+ reg = <0x51>;
+ };
+};
+
+
+&mac0 {
+ phy-mode = "rmii";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mac0_pins_a>;
+ phy-reset-gpios = <&gpio4 13 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};
+
+&pinctrl{
+ pinctrl-names = "default";
+ pinctrl-0 = <&hog_pins_cpuimx283>;
+
+ hog_pins_cpuimx283: hog-cpuimx283@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_ENET0_RX_CLK__GPIO_4_13
+ MX28_PAD_ENET0_TX_CLK__GPIO_4_5
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_ENABLE>;
+ };
+};
new file mode 100644
@@ -0,0 +1,50 @@
+/*
+ * Copyright 2013 Eukréa Electromatique <eric@eukrea.com>
+ * Copyright 2013 Eukréa Electromatique <denis@eukrea.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version 2
+ * of the License, or (at your option) any later version.
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+/*
+ * Module contains : i.MX287 + 128MB DDR2 + NAND + 2 x Ethernet PHY + RTC
+ */
+
+#include "imx28-eukrea-mbmx283lc.dts"
+
+/ {
+ model = "Eukrea Electromatique MBMX287LC";
+ compatible = "eukrea,mbmx287lc", "eukrea,mbmx283lc", "eukrea,mbmx28lc", "fsl,imx28";
+
+ memory {
+ reg = <0x40000000 0x08000000>;
+ };
+};
+
+&mac1 {
+ phy-mode = "rmii";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mac1_pins_a>;
+ phy-reset-gpios = <&gpio3 27 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+};
+
+&pinctrl {
+ pinctrl-names = "default";
+ pinctrl-0 = <&hog_pins_cpuimx283 &hog_pins_cpuimx287>;
+ hog_pins_cpuimx287: hog-cpuimx287@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_SPDIF__GPIO_3_27
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_ENABLE>;
+ };
+};
new file mode 100644
@@ -0,0 +1,326 @@
+/*
+ * Copyright 2013 Eukréa Electromatique <eric@eukrea.com>
+ * Copyright 2013 Eukréa Electromatique <denis@eukrea.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version 2
+ * of the License, or (at your option) any later version.
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+#include "imx28.dtsi"
+
+/ {
+ model = "Eukrea Electromatique MBMX28LC";
+ compatible = "eukrea,mbmx28lc", "fsl,imx28";
+
+ backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm 4 1000000>;
+ brightness-levels = <0 25 50 75 100 125 150 175 200 225 255>;
+ default-brightness-level = <10>;
+ };
+
+ button-sw3 {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpio_button_sw3_pins_mbmx28lc>;
+
+ sw3 {
+ label = "SW3";
+ gpios = <&gpio1 21 GPIO_ACTIVE_LOW>;
+ linux,code = <BTN_MISC>;
+ gpio-key,wakeup;
+ };
+ };
+
+ button-sw4 {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpio_button_sw4_pins_mbmx28lc>;
+
+ sw4 {
+ label = "SW4";
+ gpios = <&gpio1 20 GPIO_ACTIVE_LOW>;
+ linux,code = <BTN_MISC>;
+ gpio-key,wakeup;
+ };
+ };
+
+ led-d6 {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_d6_pins_mbmx28lc>;
+
+ led1 {
+ label = "d6";
+ gpios = <&gpio1 23 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ led-d7 {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_d7_pins_mbmx28lc>;
+
+ led1 {
+ label = "d7";
+ gpios = <&gpio1 22 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "default-on";
+ };
+ };
+
+ regulators {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ reg_3p3v: regulator@0 {
+ compatible = "regulator-fixed";
+ regulator-name = "3P3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ reg_lcd_3v3: regulator@1 {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <®_lcd_3v3_pins_mbmx28lc>;
+ regulator-name = "lcd-3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio3 30 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_usb0_vbus: regulator@2 {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <®_usb0_vbus_pins_mbmx28lc>;
+ regulator-name = "usb0_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio1 18 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_usb1_vbus: regulator@3 {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <®_usb1_vbus_pins_mbmx28lc>;
+ regulator-name = "usb1_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio1 19 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+ };
+
+ sound {
+ compatible = "fsl,imx28-mbmx28lc-sgtl5000",
+ "fsl,mxs-audio-sgtl5000";
+ model = "imx28-mbmx28lc-sgtl5000";
+ saif-controllers = <&saif0 &saif1>;
+ audio-codec = <&sgtl5000>;
+ };
+};
+
+&duart {
+ pinctrl-names = "default";
+ pinctrl-0 = <&duart_4pins_a>;
+ status = "okay";
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+
+ sgtl5000: codec@0a {
+ compatible = "fsl,sgtl5000";
+ reg = <0x0a>;
+ VDDA-supply = <®_3p3v>;
+ VDDIO-supply = <®_3p3v>;
+ clocks = <&saif0>;
+ };
+};
+
+&lcdif {
+ pinctrl-names = "default";
+ pinctrl-0 = <&lcdif_18bit_pins_a &lcdif_pins_mbmx28lc>;
+ lcd-supply = <®_lcd_3v3>;
+ display = <&display0>;
+ status = "okay";
+
+ display0: display0 {
+ model = "43WVF1G-0";
+ bits-per-pixel = <16>;
+ bus-width = <18>;
+
+ display-timings {
+ native-mode = <&timing0>;
+ timing0: timing0 {
+ clock-frequency = <9072000>;
+ hactive = <480>;
+ vactive = <272>;
+ hback-porch = <10>;
+ hfront-porch = <5>;
+ vback-porch = <8>;
+ vfront-porch = <8>;
+ hsync-len = <40>;
+ vsync-len = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+ };
+ };
+};
+
+&lradc {
+ fsl,lradc-touchscreen-wires = <4>;
+ status = "okay";
+};
+
+&pinctrl {
+ gpio_button_sw3_pins_mbmx28lc: gpio-button-sw3-mbmx28lc@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_LCD_D21__GPIO_1_21
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ gpio_button_sw4_pins_mbmx28lc: gpio-button-sw4-mbmx28lc@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_LCD_D20__GPIO_1_20
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ lcdif_pins_mbmx28lc: lcdif-mbmx28lc@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_LCD_VSYNC__LCD_VSYNC
+ MX28_PAD_LCD_HSYNC__LCD_HSYNC
+ MX28_PAD_LCD_DOTCLK__LCD_DOTCLK
+ MX28_PAD_LCD_ENABLE__LCD_ENABLE
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ led_d6_pins_mbmx28lc: led-d6-mbmx28lc@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_LCD_D23__GPIO_1_23
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ led_d7_pins_mbmx28lc: led-d7-mbmx28lc@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_LCD_D22__GPIO_1_22
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ reg_lcd_3v3_pins_mbmx28lc: lcd-3v3-mbmx28lc@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_LCD_RESET__GPIO_3_30
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ reg_usb0_vbus_pins_mbmx28lc: reg-usb0-vbus-mbmx28lc@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_LCD_D18__GPIO_1_18
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ reg_usb1_vbus_pins_mbmx28lc: reg-usb1-vbus-mbmx28lc@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_LCD_D19__GPIO_1_19
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+};
+
+&pwm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm4_pins_a>;
+ status = "okay";
+};
+
+&saif0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&saif0_pins_a>;
+ status = "okay";
+};
+
+&saif1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&saif1_pins_a>;
+ fsl,saif-master = <&saif0>;
+ status = "okay";
+};
+
+&ssp0 {
+ compatible = "fsl,imx28-mmc";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_4bit_pins_a &mmc0_cd_cfg &mmc0_sck_cfg>;
+ bus-width = <4>;
+ cd-inverted;
+ status = "okay";
+};
+
+&usb0 {
+ disable-over-current;
+ vbus-supply = <®_usb0_vbus>;
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb0_id_pins_b>;
+};
+
+&usb1 {
+ vbus-supply = <®_usb1_vbus>;
+ status = "okay";
+};
+
+&usbphy0 {
+ status = "okay";
+};
+
+&usbphy1 {
+ status = "okay";
+};
@@ -448,6 +448,12 @@ static int __init mxs_restart_init(void)
return 0;
}
+static void __init eukrea_mbmx283lc_init(void)
+{
+ enable_clk_enet_out();
+ mxs_saif_clkmux_select(MXS_DIGCTL_SAIF_CLKMUX_EXTMSTR0);
+}
+
static void __init mxs_machine_init(void)
{
struct device_node *root;
@@ -486,6 +492,8 @@ static void __init mxs_machine_init(void)
apx4devkit_init();
else if (of_machine_is_compatible("crystalfontz,cfa10036"))
crystalfontz_init();
+ else if (of_machine_is_compatible("eukrea,mbmx283lc"))
+ eukrea_mbmx283lc_init();
else if (of_machine_is_compatible("i2se,duckbill"))
duckbill_init();
else if (of_machine_is_compatible("msr,m28cu3"))