@@ -50,6 +50,7 @@ obj-$(CONFIG_SAMSUNG_DMADEV) += dma-ops.o
obj-$(CONFIG_SAMSUNG_PM) += pm.o
obj-$(CONFIG_SAMSUNG_PM_GPIO) += pm-gpio.o
obj-$(CONFIG_SAMSUNG_PM_CHECK) += pm-check.o
+obj-$(CONFIG_SAMSUNG_PM_DEBUG) += pm-debug.o
obj-$(CONFIG_SAMSUNG_WAKEMASK) += wakeup-mask.o
obj-$(CONFIG_SAMSUNG_WDT_RESET) += watchdog-reset.o
new file mode 100644
@@ -0,0 +1,70 @@
+/*
+ * Copyright (C) 2013 Samsung Electronics Co., Ltd.
+ * Tomasz Figa <t.figa@samsung.com>
+ * Copyright (c) 2004 Simtec Electronics
+ * http://armlinux.simtec.co.uk/
+ * Written by Ben Dooks, <ben@simtec.co.uk>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#ifndef __PLAT_SAMSUNG_PM_COMMON_H
+#define __PLAT_SAMSUNG_PM_COMMON_H __FILE__
+
+/* PM debug functions */
+
+/**
+ * struct pm_uart_save - save block for core UART
+ * @ulcon: Save value for S3C2410_ULCON
+ * @ucon: Save value for S3C2410_UCON
+ * @ufcon: Save value for S3C2410_UFCON
+ * @umcon: Save value for S3C2410_UMCON
+ * @ubrdiv: Save value for S3C2410_UBRDIV
+ *
+ * Save block for UART registers to be held over sleep and restored if they
+ * are needed (say by debug).
+*/
+struct pm_uart_save {
+ u32 ulcon;
+ u32 ucon;
+ u32 ufcon;
+ u32 umcon;
+ u32 ubrdiv;
+ u32 udivslot;
+};
+
+#ifdef CONFIG_SAMSUNG_PM_DEBUG
+/**
+ * s3c_pm_dbg() - low level debug function for use in suspend/resume.
+ * @msg: The message to print.
+ *
+ * This function is used mainly to debug the resume process before the system
+ * can rely on printk/console output. It uses the low-level debugging output
+ * routine printascii() to do its work.
+ */
+extern void s3c_pm_dbg(const char *msg, ...);
+
+/**
+ * s3c_pm_debug_init() - suspend/resume low level debug initialization.
+ * @base: Virtual base of UART to use for suspend/resume debugging.
+ *
+ * This function needs to be called before S3C_PMDBG() can be used, to set up
+ * UART port base address and configuration.
+ */
+extern void s3c_pm_debug_init(void);
+
+#define S3C_PMDBG(fmt...) s3c_pm_dbg(fmt)
+
+extern void s3c_pm_save_uarts(void);
+extern void s3c_pm_restore_uarts(void);
+#else
+#define S3C_PMDBG(fmt...) printk(KERN_DEBUG fmt)
+#define s3c_pm_debug_init() do { } while(0)
+
+static inline void s3c_pm_save_uarts(void) { }
+static inline void s3c_pm_restore_uarts(void) { }
+#endif
+
+#endif
@@ -16,6 +16,7 @@
*/
#include <linux/irq.h>
+#include <plat/pm-common.h>
struct device;
@@ -76,26 +77,6 @@ struct sleep_save {
#define SAVE_ITEM(x) \
{ .reg = (x) }
-/**
- * struct pm_uart_save - save block for core UART
- * @ulcon: Save value for S3C2410_ULCON
- * @ucon: Save value for S3C2410_UCON
- * @ufcon: Save value for S3C2410_UFCON
- * @umcon: Save value for S3C2410_UMCON
- * @ubrdiv: Save value for S3C2410_UBRDIV
- *
- * Save block for UART registers to be held over sleep and restored if they
- * are needed (say by debug).
-*/
-struct pm_uart_save {
- u32 ulcon;
- u32 ucon;
- u32 ufcon;
- u32 umcon;
- u32 ubrdiv;
- u32 udivslot;
-};
-
/* helper functions to save/restore lists of registers. */
extern void s3c_pm_do_save(struct sleep_save *ptr, int count);
@@ -112,24 +93,6 @@ extern void s3c_cpu_resume(void);
#define s3c_cpu_resume NULL
#endif
-/* PM debug functions */
-
-#ifdef CONFIG_SAMSUNG_PM_DEBUG
-/**
- * s3c_pm_dbg() - low level debug function for use in suspend/resume.
- * @msg: The message to print.
- *
- * This function is used mainly to debug the resume process before the system
- * can rely on printk/console output. It uses the low-level debugging output
- * routine printascii() to do its work.
- */
-extern void s3c_pm_dbg(const char *msg, ...);
-
-#define S3C_PMDBG(fmt...) s3c_pm_dbg(fmt)
-#else
-#define S3C_PMDBG(fmt...) printk(KERN_DEBUG fmt)
-#endif
-
#ifdef CONFIG_S3C_PM_DEBUG_LED_SMDK
/**
* s3c_pm_debug_smdkled() - Debug PM suspend/resume via SMDK Board LEDs
new file mode 100644
@@ -0,0 +1,98 @@
+/*
+ * Copyright (C) 2013 Samsung Electronics Co., Ltd.
+ * Tomasz Figa <t.figa@samsung.com>
+ * Copyright (C) 2008 Openmoko, Inc.
+ * Copyright (C) 2004-2008 Simtec Electronics
+ * Ben Dooks <ben@simtec.co.uk>
+ * http://armlinux.simtec.co.uk/
+ *
+ * Samsung common power management (suspend to RAM) debug support
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/serial_core.h>
+#include <linux/io.h>
+
+#include <asm/mach/map.h>
+
+#include <plat/cpu.h>
+#include <plat/pm-common.h>
+#include <plat/regs-serial.h>
+
+#ifdef CONFIG_SAMSUNG_ATAGS
+#include <mach/pm-core.h>
+#else
+static inline void s3c_pm_debug_init_uart(void) {}
+static inline void s3c_pm_arch_update_uart(void __iomem *regs,
+ struct pm_uart_save *save) {}
+#endif
+
+static struct pm_uart_save uart_save;
+
+extern void printascii(const char *);
+
+void s3c_pm_dbg(const char *fmt, ...)
+{
+ va_list va;
+ char buff[256];
+
+ va_start(va, fmt);
+ vsnprintf(buff, sizeof(buff), fmt, va);
+ va_end(va);
+
+ printascii(buff);
+}
+
+void s3c_pm_debug_init(void)
+{
+ /* restart uart clocks so we can use them to output */
+ s3c_pm_debug_init_uart();
+}
+
+static inline void __iomem *s3c_pm_uart_base(void)
+{
+ unsigned long paddr;
+ unsigned long vaddr;
+
+ debug_ll_addr(&paddr, &vaddr);
+
+ return (void __iomem *)vaddr;
+}
+
+void s3c_pm_save_uarts(void)
+{
+ void __iomem *regs = s3c_pm_uart_base();
+ struct pm_uart_save *save = &uart_save;
+
+ save->ulcon = __raw_readl(regs + S3C2410_ULCON);
+ save->ucon = __raw_readl(regs + S3C2410_UCON);
+ save->ufcon = __raw_readl(regs + S3C2410_UFCON);
+ save->umcon = __raw_readl(regs + S3C2410_UMCON);
+ save->ubrdiv = __raw_readl(regs + S3C2410_UBRDIV);
+
+ if (!soc_is_s3c2410())
+ save->udivslot = __raw_readl(regs + S3C2443_DIVSLOT);
+
+ S3C_PMDBG("UART[%p]: ULCON=%04x, UCON=%04x, UFCON=%04x, UBRDIV=%04x\n",
+ regs, save->ulcon, save->ucon, save->ufcon, save->ubrdiv);
+}
+
+void s3c_pm_restore_uarts(void)
+{
+ void __iomem *regs = s3c_pm_uart_base();
+ struct pm_uart_save *save = &uart_save;
+
+ s3c_pm_arch_update_uart(regs, save);
+
+ __raw_writel(save->ulcon, regs + S3C2410_ULCON);
+ __raw_writel(save->ucon, regs + S3C2410_UCON);
+ __raw_writel(save->ufcon, regs + S3C2410_UFCON);
+ __raw_writel(save->umcon, regs + S3C2410_UMCON);
+ __raw_writel(save->ubrdiv, regs + S3C2410_UBRDIV);
+
+ if (!soc_is_s3c2410())
+ __raw_writel(save->udivslot, regs + S3C2443_DIVSLOT);
+}
@@ -17,16 +17,11 @@
#include <linux/errno.h>
#include <linux/delay.h>
#include <linux/of.h>
-#include <linux/serial_core.h>
#include <linux/io.h>
#include <asm/cacheflush.h>
-#include <asm/mach/map.h>
#include <asm/suspend.h>
-#include <plat/cpu.h>
-#include <plat/regs-serial.h>
-
#ifdef CONFIG_SAMSUNG_ATAGS
#include <mach/hardware.h>
#include <mach/map.h>
@@ -44,86 +39,6 @@
unsigned long s3c_pm_flags;
-/* Debug code:
- *
- * This code supports debug output to the low level UARTs for use on
- * resume before the console layer is available.
-*/
-
-#ifdef CONFIG_SAMSUNG_PM_DEBUG
-extern void printascii(const char *);
-
-void s3c_pm_dbg(const char *fmt, ...)
-{
- va_list va;
- char buff[256];
-
- va_start(va, fmt);
- vsnprintf(buff, sizeof(buff), fmt, va);
- va_end(va);
-
- printascii(buff);
-}
-
-static inline void s3c_pm_debug_init(void)
-{
- /* restart uart clocks so we can use them to output */
- s3c_pm_debug_init_uart();
-}
-
-static struct pm_uart_save uart_save;
-
-static inline void __iomem *s3c_pm_uart_base(void)
-{
- unsigned long paddr;
- unsigned long vaddr;
-
- debug_ll_addr(&paddr, &vaddr);
-
- return (void __iomem *)vaddr;
-}
-
-static void s3c_pm_save_uarts(void)
-{
- void __iomem *regs = s3c_pm_uart_base();
- struct pm_uart_save *save = &uart_save;
-
- save->ulcon = __raw_readl(regs + S3C2410_ULCON);
- save->ucon = __raw_readl(regs + S3C2410_UCON);
- save->ufcon = __raw_readl(regs + S3C2410_UFCON);
- save->umcon = __raw_readl(regs + S3C2410_UMCON);
- save->ubrdiv = __raw_readl(regs + S3C2410_UBRDIV);
-
- if (!soc_is_s3c2410())
- save->udivslot = __raw_readl(regs + S3C2443_DIVSLOT);
-
- S3C_PMDBG("UART[%p]: ULCON=%04x, UCON=%04x, UFCON=%04x, UBRDIV=%04x\n",
- regs, save->ulcon, save->ucon, save->ufcon, save->ubrdiv);
-}
-
-static void s3c_pm_restore_uarts(void)
-{
- void __iomem *regs = s3c_pm_uart_base();
- struct pm_uart_save *save = &uart_save;
-
- s3c_pm_arch_update_uart(regs, save);
-
- __raw_writel(save->ulcon, regs + S3C2410_ULCON);
- __raw_writel(save->ucon, regs + S3C2410_UCON);
- __raw_writel(save->ufcon, regs + S3C2410_UFCON);
- __raw_writel(save->umcon, regs + S3C2410_UMCON);
- __raw_writel(save->ubrdiv, regs + S3C2410_UBRDIV);
-
- if (!soc_is_s3c2410())
- __raw_writel(save->udivslot, regs + S3C2443_DIVSLOT);
-}
-#else
-#define s3c_pm_debug_init() do { } while(0)
-
-static void s3c_pm_save_uarts(void) { }
-static void s3c_pm_restore_uarts(void) { }
-#endif
-
/* The IRQ ext-int code goes here, it is too small to currently bother
* with its own file. */
Not all Samsung SoC platforms are going to use the legacy Samsung PM code enabled by CONFIG_SAMSUNG_PM_DEBUG. To allow using Samsung PM debug helpers on such platforms, related code is moved to separate file and a plat/pm-common.h header is added to separate legacy and generic code. Signed-off-by: Tomasz Figa <t.figa@samsung.com> --- arch/arm/plat-samsung/Makefile | 1 + arch/arm/plat-samsung/include/plat/pm-common.h | 70 ++++++++++++++++++ arch/arm/plat-samsung/include/plat/pm.h | 39 +--------- arch/arm/plat-samsung/pm-debug.c | 98 ++++++++++++++++++++++++++ arch/arm/plat-samsung/pm.c | 85 ---------------------- 5 files changed, 170 insertions(+), 123 deletions(-) create mode 100644 arch/arm/plat-samsung/include/plat/pm-common.h create mode 100644 arch/arm/plat-samsung/pm-debug.c