@@ -20,13 +20,9 @@ CONFIG_MACH_RD88F6281=y
CONFIG_MACH_T5325=y
CONFIG_MACH_TS219=y
CONFIG_MACH_TS41X=y
-CONFIG_ARCH_KIRKWOOD_DT=y
-CONFIG_MACH_MV88F6281GTW_GE_DT=y
# CONFIG_CPU_FEROCEON_OLD_ID is not set
-CONFIG_PCI_MVEBU=y
CONFIG_PREEMPT=y
CONFIG_AEABI=y
-# CONFIG_OABI_COMPAT is not set
CONFIG_HIGHMEM=y
CONFIG_ZBOOT_ROM_TEXT=0x0
CONFIG_ZBOOT_ROM_BSS=0x0
@@ -85,7 +81,6 @@ CONFIG_LEGACY_PTY_COUNT=16
CONFIG_SERIAL_8250=y
CONFIG_SERIAL_8250_CONSOLE=y
CONFIG_SERIAL_8250_RUNTIME_UARTS=2
-CONFIG_SERIAL_OF_PLATFORM=y
# CONFIG_HW_RANDOM is not set
CONFIG_I2C=y
# CONFIG_I2C_COMPAT is not set
@@ -176,5 +171,4 @@ CONFIG_CRYPTO_PCBC=m
# CONFIG_CRYPTO_ANSI_CPRNG is not set
CONFIG_CRYPTO_DEV_MV_CESA=y
CONFIG_CRC_CCITT=y
-CONFIG_CRC16=y
CONFIG_LIBCRC32C=y
@@ -88,24 +88,6 @@ config MACH_TS41X
QNAP TS-410, TS-410U, TS-419P, TS-419P+ and TS-419U Turbo
NAS devices.
-comment "Device tree entries"
-
-config ARCH_KIRKWOOD_DT
- bool "Marvell Kirkwood Flattened Device Tree"
- select KIRKWOOD_CLK
- select OF_IRQ
- select ORION_IRQCHIP
- select ORION_TIMER
- select POWER_SUPPLY
- select POWER_RESET
- select POWER_RESET_GPIO
- select REGULATOR
- select REGULATOR_FIXED_VOLTAGE
- select USE_OF
- help
- Say 'Y' here if you want your kernel to support the
- Marvell Kirkwood using flattened device tree.
-
endmenu
endif
@@ -10,5 +10,3 @@ obj-$(CONFIG_MACH_RD88F6281) += rd88f6281-setup.o
obj-$(CONFIG_MACH_T5325) += t5325-setup.o
obj-$(CONFIG_MACH_TS219) += ts219-setup.o tsx1x-common.o
obj-$(CONFIG_MACH_TS41X) += ts41x-setup.o tsx1x-common.o
-
-obj-$(CONFIG_ARCH_KIRKWOOD_DT) += board-dt.o
deleted file mode 100644
@@ -1,228 +0,0 @@
-/*
- * Copyright 2012 (C), Jason Cooper <jason@lakedaemon.net>
- *
- * arch/arm/mach-kirkwood/board-dt.c
- *
- * Flattened Device Tree board initialization
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <linux/clk.h>
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/of.h>
-#include <linux/of_address.h>
-#include <linux/of_net.h>
-#include <linux/of_platform.h>
-#include <linux/dma-mapping.h>
-#include <linux/irqchip.h>
-#include <linux/kexec.h>
-#include <asm/hardware/cache-feroceon-l2.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <mach/bridge-regs.h>
-#include <plat/common.h>
-#include <plat/pcie.h>
-#include "pm.h"
-
-static struct map_desc kirkwood_io_desc[] __initdata = {
- {
- .virtual = (unsigned long) KIRKWOOD_REGS_VIRT_BASE,
- .pfn = __phys_to_pfn(KIRKWOOD_REGS_PHYS_BASE),
- .length = KIRKWOOD_REGS_SIZE,
- .type = MT_DEVICE,
- },
-};
-
-static void __init kirkwood_map_io(void)
-{
- iotable_init(kirkwood_io_desc, ARRAY_SIZE(kirkwood_io_desc));
-}
-
-static struct resource kirkwood_cpufreq_resources[] = {
- [0] = {
- .start = CPU_CONTROL_PHYS,
- .end = CPU_CONTROL_PHYS + 3,
- .flags = IORESOURCE_MEM,
- },
-};
-
-static struct platform_device kirkwood_cpufreq_device = {
- .name = "kirkwood-cpufreq",
- .id = -1,
- .num_resources = ARRAY_SIZE(kirkwood_cpufreq_resources),
- .resource = kirkwood_cpufreq_resources,
-};
-
-static void __init kirkwood_cpufreq_init(void)
-{
- platform_device_register(&kirkwood_cpufreq_device);
-}
-
-static struct resource kirkwood_cpuidle_resource[] = {
- {
- .flags = IORESOURCE_MEM,
- .start = DDR_OPERATION_BASE,
- .end = DDR_OPERATION_BASE + 3,
- },
-};
-
-static struct platform_device kirkwood_cpuidle = {
- .name = "kirkwood_cpuidle",
- .id = -1,
- .resource = kirkwood_cpuidle_resource,
- .num_resources = 1,
-};
-
-static void __init kirkwood_cpuidle_init(void)
-{
- platform_device_register(&kirkwood_cpuidle);
-}
-
-/* Temporary here since mach-mvebu has a function we can use */
-static void kirkwood_restart(enum reboot_mode mode, const char *cmd)
-{
- /*
- * Enable soft reset to assert RSTOUTn.
- */
- writel(SOFT_RESET_OUT_EN, RSTOUTn_MASK);
-
- /*
- * Assert soft reset.
- */
- writel(SOFT_RESET, SYSTEM_SOFT_RESET);
-
- while (1)
- ;
-}
-
-#define MV643XX_ETH_MAC_ADDR_LOW 0x0414
-#define MV643XX_ETH_MAC_ADDR_HIGH 0x0418
-
-static void __init kirkwood_dt_eth_fixup(void)
-{
- struct device_node *np;
-
- /*
- * The ethernet interfaces forget the MAC address assigned by u-boot
- * if the clocks are turned off. Usually, u-boot on kirkwood boards
- * has no DT support to properly set local-mac-address property.
- * As a workaround, we get the MAC address from mv643xx_eth registers
- * and update the port device node if no valid MAC address is set.
- */
- for_each_compatible_node(np, NULL, "marvell,kirkwood-eth-port") {
- struct device_node *pnp = of_get_parent(np);
- struct clk *clk;
- struct property *pmac;
- void __iomem *io;
- u8 *macaddr;
- u32 reg;
-
- if (!pnp)
- continue;
-
- /* skip disabled nodes or nodes with valid MAC address*/
- if (!of_device_is_available(pnp) || of_get_mac_address(np))
- goto eth_fixup_skip;
-
- clk = of_clk_get(pnp, 0);
- if (IS_ERR(clk))
- goto eth_fixup_skip;
-
- io = of_iomap(pnp, 0);
- if (!io)
- goto eth_fixup_no_map;
-
- /* ensure port clock is not gated to not hang CPU */
- clk_prepare_enable(clk);
-
- /* store MAC address register contents in local-mac-address */
- pr_err(FW_INFO "%s: local-mac-address is not set\n",
- np->full_name);
-
- pmac = kzalloc(sizeof(*pmac) + 6, GFP_KERNEL);
- if (!pmac)
- goto eth_fixup_no_mem;
-
- pmac->value = pmac + 1;
- pmac->length = 6;
- pmac->name = kstrdup("local-mac-address", GFP_KERNEL);
- if (!pmac->name) {
- kfree(pmac);
- goto eth_fixup_no_mem;
- }
-
- macaddr = pmac->value;
- reg = readl(io + MV643XX_ETH_MAC_ADDR_HIGH);
- macaddr[0] = (reg >> 24) & 0xff;
- macaddr[1] = (reg >> 16) & 0xff;
- macaddr[2] = (reg >> 8) & 0xff;
- macaddr[3] = reg & 0xff;
-
- reg = readl(io + MV643XX_ETH_MAC_ADDR_LOW);
- macaddr[4] = (reg >> 8) & 0xff;
- macaddr[5] = reg & 0xff;
-
- of_update_property(np, pmac);
-
-eth_fixup_no_mem:
- iounmap(io);
- clk_disable_unprepare(clk);
-eth_fixup_no_map:
- clk_put(clk);
-eth_fixup_skip:
- of_node_put(pnp);
- }
-}
-
-/*
- * Disable propagation of mbus errors to the CPU local bus, as this
- * causes mbus errors (which can occur for example for PCI aborts) to
- * throw CPU aborts, which we're not set up to deal with.
- */
-static void __init kirkwood_disable_mbus_error_propagation(void)
-{
- void __iomem *cpu_config;
-
- cpu_config = ioremap(CPU_CONFIG_PHYS, 4);
- writel(readl(cpu_config) & ~CPU_CONFIG_ERROR_PROP, cpu_config);
- iounmap(cpu_config);
-}
-
-static void __init kirkwood_dt_init(void)
-{
- kirkwood_disable_mbus_error_propagation();
-
- BUG_ON(mvebu_mbus_dt_init());
-
-#ifdef CONFIG_CACHE_FEROCEON_L2
- feroceon_of_init();
-#endif
- kirkwood_cpufreq_init();
- kirkwood_cpuidle_init();
-
- kirkwood_pm_init();
- kirkwood_dt_eth_fixup();
-
-#ifdef CONFIG_KEXEC
- kexec_reinit = kirkwood_enable_pcie;
-#endif
-
- of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL);
-}
-
-static const char * const kirkwood_dt_board_compat[] = {
- "marvell,kirkwood",
- NULL
-};
-
-DT_MACHINE_START(KIRKWOOD_DT, "Marvell Kirkwood (Flattened Device Tree)")
- /* Maintainer: Jason Cooper <jason@lakedaemon.net> */
- .map_io = kirkwood_map_io,
- .init_machine = kirkwood_dt_init,
- .restart = kirkwood_restart,
- .dt_compat = kirkwood_dt_board_compat,
-MACHINE_END