@@ -97,6 +97,15 @@ config SATA_AHCI_PLATFORM
If unsure, say N.
+config AHCI_DA850
+ tristate "DaVinci DA850 AHCI SATA support"
+ depends on ARCH_DAVINCI_DA850
+ help
+ This option enables support for the DaVinci DA850 SoC's
+ onboard AHCI SATA.
+
+ If unsure, say N.
+
config AHCI_ST
tristate "ST AHCI SATA support"
depends on ARCH_STI
@@ -10,6 +10,7 @@ obj-$(CONFIG_SATA_INIC162X) += sata_inic162x.o
obj-$(CONFIG_SATA_SIL24) += sata_sil24.o
obj-$(CONFIG_SATA_DWC) += sata_dwc_460ex.o
obj-$(CONFIG_SATA_HIGHBANK) += sata_highbank.o libahci.o
+obj-$(CONFIG_AHCI_DA850) += ahci_da850.o libahci.o libahci_platform.o
obj-$(CONFIG_AHCI_IMX) += ahci_imx.o libahci.o libahci_platform.o
obj-$(CONFIG_AHCI_SUNXI) += ahci_sunxi.o libahci.o libahci_platform.o
obj-$(CONFIG_AHCI_ST) += ahci_st.o libahci.o libahci_platform.o
new file mode 100644
@@ -0,0 +1,114 @@
+/*
+ * DaVinci DA850 AHCI SATA platform driver
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2, or (at your option)
+ * any later version.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pm.h>
+#include <linux/device.h>
+#include <linux/platform_device.h>
+#include <linux/libata.h>
+#include <linux/ahci_platform.h>
+#include "ahci.h"
+
+/* SATA PHY Control Register offset from AHCI base */
+#define SATA_P0PHYCR_REG 0x178
+
+#define SATA_PHY_MPY(x) ((x) << 0)
+#define SATA_PHY_LOS(x) ((x) << 6)
+#define SATA_PHY_RXCDR(x) ((x) << 10)
+#define SATA_PHY_RXEQ(x) ((x) << 13)
+#define SATA_PHY_TXSWING(x) ((x) << 19)
+#define SATA_PHY_ENPLL(x) ((x) << 31)
+
+/*
+ * The multiplier needed for 1.5GHz PLL output.
+ *
+ * NOTE: This is currently hardcoded to be suitable for 100MHz crystal
+ * frequency (which is used by DA850 EVM board) and may need to be changed
+ * if you would like to use this driver on some other board.
+ */
+#define DA850_SATA_CLK_MULTIPLIER 7
+
+static void da850_sata_init(struct device *dev, void __iomem *pwrdn_reg,
+ void __iomem *ahci_base)
+{
+ unsigned int val;
+
+ /* Enable SATA clock receiver */
+ val = readl(pwrdn_reg);
+ val &= ~BIT(0);
+ writel(val, pwrdn_reg);
+
+ val = SATA_PHY_MPY(DA850_SATA_CLK_MULTIPLIER + 1) | SATA_PHY_LOS(1) |
+ SATA_PHY_RXCDR(4) | SATA_PHY_RXEQ(1) | SATA_PHY_TXSWING(3) |
+ SATA_PHY_ENPLL(1);
+
+ writel(val, ahci_base + SATA_P0PHYCR_REG);
+}
+
+static const struct ata_port_info ahci_da850_port_info = {
+ .flags = AHCI_FLAG_COMMON,
+ .pio_mask = ATA_PIO4,
+ .udma_mask = ATA_UDMA6,
+ .port_ops = &ahci_platform_ops,
+};
+
+static int ahci_da850_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct ahci_host_priv *hpriv;
+ struct resource *res;
+ void __iomem *pwrdn_reg;
+ int rc;
+
+ hpriv = ahci_platform_get_resources(pdev);
+ if (IS_ERR(hpriv))
+ return PTR_ERR(hpriv);
+
+ rc = ahci_platform_enable_resources(hpriv);
+ if (rc)
+ return rc;
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
+ if (!res)
+ goto disable_resources;
+
+ pwrdn_reg = devm_ioremap(dev, res->start, resource_size(res));
+ if (!pwrdn_reg)
+ goto disable_resources;
+
+ da850_sata_init(dev, pwrdn_reg, hpriv->mmio);
+
+ rc = ahci_platform_init_host(pdev, hpriv, &ahci_da850_port_info, 0, 0);
+ if (rc)
+ goto disable_resources;
+
+ return 0;
+disable_resources:
+ ahci_platform_disable_resources(hpriv);
+ return rc;
+}
+
+static SIMPLE_DEV_PM_OPS(ahci_da850_pm_ops, ahci_platform_suspend,
+ ahci_platform_resume);
+
+static struct platform_driver ahci_da850_driver = {
+ .probe = ahci_da850_probe,
+ .remove = ata_platform_remove_one,
+ .driver = {
+ .name = "ahci_da850",
+ .owner = THIS_MODULE,
+ .pm = &ahci_da850_pm_ops,
+ },
+};
+module_platform_driver(ahci_da850_driver);
+
+MODULE_DESCRIPTION("DaVinci DA850 AHCI SATA platform driver");
+MODULE_AUTHOR("Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>");
+MODULE_LICENSE("GPL");
Add the new ahci_da850 host driver. Platform changes needed to make DaVinci DA850 SATA AHCI support fully functional are in the separate "ARM: davinci: da850: update SATA AHCI support" commit. Please note that this driver doesn't have the superfluous clock control code as clock is already handled by the generic AHCI platform library code. Cc: Sekhar Nori <nsekhar@ti.com> Cc: Kevin Hilman <khilman@deeprootsystems.com> Cc: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> --- v4: - no changes v3: - merged changes from Sekhar - splitted out platform changes into separate patch v2: - dropped the experimental tag from the config option help - fixed SYSCFG1 memory resource handling - hardcoded the multiplier data and added a note about it - used readl()/writel() instead of __raw_readl()/__raw_writel() - dropped the superflous clock control - cleaned up da850_sata_init() - changed the platform device name and removed the platform ids table - removed the deprecated ahci_platform_data platform code - updated the patch description drivers/ata/Kconfig | 9 ++++ drivers/ata/Makefile | 1 + drivers/ata/ahci_da850.c | 114 +++++++++++++++++++++++++++++++++++++++++++++++ 3 files changed, 124 insertions(+) create mode 100644 drivers/ata/ahci_da850.c